Bedienungsanleitung DMR-140 Inhaltsverzeichnis Kapitel Thema Sicherheitshinweise 1. DVR Features 2. Bedienelemente und Anschlüsse 2.1 Frontplatte 2.2 Rückseite mit Anschlüsse 2.3 Ferbedienung 3. Installation 3.1 Festplatte einbauen 3.2 Anschluss von Kamera und Monitor 3.3 Anschluss eines Netzteils 4. System-Start 4.1 Erkennen der eingebauten Festplatte 4.2 Datenwiederherstellung nach Stromausfall 4.3 Aufnahmestart nach Stromausfall 4.4 Monitoranzeige 5. Einstellungen 5.1 Setup Menü 5.
Bedienungsanleitung DMR-140 Hinweise für den sicheren Gebrauch Die Geräte (Recorder und Netzgerät) entsprechen allen erforderlichen Richtlinien der EU und sind deshalb mit CE gekennzeichnet. WARNUNG Das Netzgerät wird mit lebensgefährlicher Netzspannung (230 V~) versorgt. Nehmen Sie deshalb niemals selbst Eingriffe am Netzgerät vor. Es besteht die Gefahr eines elektrischen Schlages.
Bedienungsanleitung DMR-140 Kapitel 1 : DVR Features • • • • • • • • 4 Kamera-Eingänge mit BNC Anschluss 1 Monitor-Ausgang mit BNC Anschluss Videoeingang wahlweise : NTSC / PAL Bewegungserkennung mit Empfindlichkeits- und Bereichseinstellung Aufnahme Wahlweise zeit- und bewegungsgesteuert Ein Anschluss für eine ATA-100 (IDE) Festplatte USB2.0-Anschluss für PC-Backup Incl. Fernbedienung und Festplattenrahmen (Festplatte optional erhältlich) Kapitel 2 : Bedienelemente und Anschlüsse 2.
Bedienungsanleitung DMR-140 2.2 Rückseite mit Anschlüssen 1 Monitorausgang 4 Kameraeingänge Lüfter Betriebsspannungsanschluss Der USB-Anschluss befindet sich an der Seite des Recorders. 2.
Bedienungsanleitung DMR-140 Kapitel 3 : Installation 3.1 Festplatte einbauen 1 Betriebsspannung entfernen. !! Festplatte nur ohne Betriebspannung wechseln !! 2 Schloss öffnen und Festplattenrahmen vorsichtig aus dem Gerät ziehen. 3 Spannungsversorgung und Datenkabel an die Festplatte anschließen. Festplatte muss dabei auf MASTER eingestellt sein. Hinweis des Herstellers beachten. Die vierpolige Verbindung ist das Powerkabel, das Flachbandkabel ist die Datenverbindung.
Bedienungsanleitung DMR-140 Kapitel 4 : System-Start 4.1 Erkennen der eingebauten Festplatte Nach dem Anlegen der Betriebsspannung startet der Recorder automatisch. Dabei wird getestet, ob eine Festplatte eingebaut ist. 4.2 Datenwiederherstellung nach Stromausfall Wird während des Betriebes die Betriebsspannung unterbrochen, können Daten verloren gehen. Nach einem Neustart kann gewählt werden, ob diese Daten wieder hergestellt werden sollen. 4.
Bedienungsanleitung DMR-140 4.4 Monitoranzeige Während das Gerät im normalen Betrieb ist zeigt der Monitor, die Kamerabildern und zusätzliche Informationen an. oben links benutzte Festplattenkapazität mitte Kamera-Nummern unten Rechts Datum und Uhrzeit unten Links System-Status Weitere Erklärungen siehe Kapitel 6.1 Kapitel 5: Einstellungen 5.1 Setup Menü Das Menü ist nur in englischer Sprache verfügbar. Die nachfolgenden Erklärungen sollen Ihnen helfen, sich schnell zurecht zu finden.
Bedienungsanleitung DMR-140 Menu : Menü aufrufen Up and Down : Cursor bewegen SEL: Einstellung wählen oder ändern Menu: Erneutes Drücken schließt das Menü 5.2 Kameraauswahl für Livebild (Camera Select) Der Recorder verfügt über eine Quad-Funktion. Damit lassen sich alle 4 Kamerasignale gleichzeitig auf dem Monitor darstellen. Über die Tasten [CH1], [CH2], [CH3], [CH4] lässt sich die Ansicht auf das Vollbild der ausgewählten Kamera umschalten.
Bedienungsanleitung DMR-140 5.4 Auflösung (Resolution) Der Recorder verfügt über zwei Aufnahmearten. Diese Aufnahmearten haben auch Einfluss auf die Livebild-Darstellung. EACH Modus In diesem Modus werden die Bilder jedes ausgewählten Eingangs einzeln verarbeitet. aufgezeichnet. Dadurch ist es möglich, bei der Wiedergabe im Vollbild-Modus jede Kamera, durch Drücken der Tasten [CH1], [CH2], [CH3], und [CH4], auch einzeln wiederzugeben.
Bedienungsanleitung DMR-140 5.6 Aufnahmequalität (Record Quality) Es stehen 3 Aufzeichnungsqualitäten zur Verfügung: High, Normal und Low Je höher die Auflösung und die Record Frame Rate eingestellt wird, desto mehr Speicherkapazität wird für die Aufzeichnung benötigt. Dies bestimmt zusammen mit der Festplattengröße die max. Aufnahmedauer. 5.7 Zeitsteuerung (Schedule Set) Zur Zeitsteuerung wird der Tag in 24 Abschnitte mit je 1 Stunde eingeteilt. Eine Wochenplanung ist nicht vorgesehen.
Bedienungsanleitung DMR-140 5.9 Passwort aktivieren (Miscellaneous Menu Passwort Enable) Wird diese Option auf “ON” gesetzt, wird für das Stoppen einer Aufnahme oder für den Zugang zur Konfiguration ein Passwort benötigt. Das voreingestellte Passwort ist 6 x die [CH1]-Taste. Bei der Einstellung “OFF” ist die Bedienung ohne Passwort möglich. 5.
Bedienungsanleitung DMR-140 5.12 Zeit- und Datumseinstellung (Miscellaneous Menu Time Set) [ Up] und [ Down] : Cursor bewegen [SEL] : Wert verändern [Menu] : Speichern und Verlassen 5.13 Festplatteneinstellung (Hard Disk Set) OVERWRITE ENABLED: YES : Endlosaufnahme (empfohlen) Die Festplatte wird immer wieder überschrieben. NO : Die Aufnahme stoppt, wenn die Festplatte voll beschreiben ist.
Bedienungsanleitung DMR-140 5.14 Bewegungserkennung (Motion Set) In diesem Punkt wird die Bewegungserkennung eingerichtet. MOTION RECORD TIME: Hier wird festgelegt, wie lange der Recorder nach erkennen einer Bewegung aufzeichnen soll. (5, 10, 15, 20, 25, 30 Sekunden) MOTION ALARM TIME: Hier wird festgelegt, wie lange der Summer nach Erkennen einer Bewegung aktiv sein soll. (OFF, 5, 10, 15, 20, 25, 30 Sekunden, CONT) CONT : Daueralarm, wird mit einem Druck auf eine beliebige Taste beendet.
Bedienungsanleitung DMR-140 5.15 Video Modus Auswahl von NTSC- oder PAL- Kamerasystemen. Da NTSC- Kameras im europäischen Raum ungebräuchlich sind, stellen Sie diese Funktion immer auf PAL ein. Dies gilt auch beim Betrieb mit S/W-Kameras. 5.16 Werkseinstellung (Factory Reset) Bitte beachten Sie, dass eine Ausführung dieses Befehl alle Ihre Einstellungen löscht. Wird dieser Punkt gewählt und dann die [SEL]-Taste betätigt, werden alle Einstellungen in den Auslieferungszustand versetzt.
Bedienungsanleitung DMR-140 Kapitel 6 Aufnahme 6.1 Aufnahme starten Um eine Aufnahme zu starten drücken Sie die [REC]-Taste. Gemäß Ihrer Zeiteinstellung (siehe. 5.7) geht das Gerät in den Aufnahmemodus. Neben den Kamerabilder werden zusätzliche Informationen in das Monitorbild eingeblendet. 1. Benutzter Speicherplatz auf der Festplatte 2. Aufnahmesymbol. 3. Kameranummer 4. Aufnahme-Modus (QUAD oder EACH) 5. Statusanzeige (REC, PLAY, FF1, FF2, FF3, REW, PAUSE) 6. HDD Info.
Bedienungsanleitung DMR-140 Kapitel 7 Wiedergabe Durch Drücken der [PLAY]-Taste wird die Wiedergabe der letzte Aufzeichnung gestartet. Wird während der Wiedergabe zusätzlich die [MENU]-Taste gedrückt, wird eine Liste mit allen bisher aufgezeichneten Sequenzen in das Bild eingeblendet. Mit den Tasten [ Up] und [ Down] kann man den Cursor (>) in der Liste bewegen. Ist der richtige Eintrag gefunden, kann die Wiedergabe mit der [PLAY]-Taste gestartet werden.
Bedienungsanleitung DMR-140 Kapitel 8 : Zugriff über die USB-Schnittstelle Über eine USB-Verbindung können Aufzeichnungen wiedergegeben und zur Datensicherung auf den PC überspielt werden. 8.1 PC Viewer installieren 1. Legen Sie die mitgelieferte CD in Ihren PC ein. 2. Öffnen Sie das Inhaltsverzeichnis der CD 3. Starten Sie die Installation durch Auswahl der “PCViewerInstall.exe”. 4. Starten Sie das PC Viewer Programm.
Bedienungsanleitung DMR-140 Bedienelement Bemerkung 1. DVR Ereignis Liste Öffnet die Liste der Aufnahmen vom DMR-140 Speichert das aktuelle Bild. Dazu muss die Wiedergabe am PC auf Pause stehen Speichert Videos im Format .mys oder .avi 2. Einzelbild speichern 3. Videos speichern 5. Gespeichertes Video laden 8. Kanalwahl Lädt ein auf dem PC gespeichertes Video Mit diesen beiden Schaltern kann zwischen der Widergabe vom PC und vom DVR umschaltet werden.
Bedienungsanleitung DMR-140 Kapitel 9 : Technische Daten Funktion Wert Bemerkung Video Format Betriebssystem Kameraeingänge NTSC / PAL embeded 4 x BNC 1 Vss Stand-alone Monitorausgang 1 x BNC 1Vss NTSC PAL NTSC PAL Anzeige Geschwindigkeit Aufnahme Geschwindigkeit Aufnahme Geschwindigkeit (EACH MODE) NTSC 120 Bilder/Sekunde 100 Bilder/Sekunde max. 30 fps (Quad) max.
Bedienungsanleitung DMR-140 Kapitel 10 Anhang 10.1 Anschlussdiagramm 10.2 Zubehör Netzkabel Netzteil Bedienungsanleitung englisch CD-ROM Fernbedienung USB Kabel Diese Bedienungsanleitung ist urheberrechtlich für MONACOR® INTERNATIONAL GmbH & Co. KG geschützt. Eine Reproduktion für eigene kommerzielle Zwecke – auch auszugsweise – ist untersagt.