User Manual CONTENTS SAFETY INSTRUCTIONS.................................................................................................................................................... 1 CHAPTER 1: DVR FEATURES........................................................................................................................................... 2 CHAPTER 2:LAYOUT ..........................................................................................................................................
User Manual 5.7 STOP RECORDING ........................................................................................................................................................... 21 CHAPTER 6: NET-VIEWER PROGRAM......................................................................................................................... 22 6.1 PLUG-INS DOWNLOAD AND INSTALLATION ..................................................................................................................... 22 6.
User Manual Safety Instructions 1. Use proper power source. Do not use this product with a power source that applies more than specified voltage (100-240V AC). 2. Never insert anything metallic into the DVR case. Putting something into the DVR case can be a source of dangerous electric shock. 3. Do not operate in wet & dusty area or use near water. Avoid places like a damp basement or dusty hallway. 4. Do not expose this product to rain or use near water.
User Manual Chapter 1: DVR Features Real time monitoring Supports real time surveillance via Monitor Saves Recordings DVR saves real-time recording image to HDD Backup Recordings Supports DVR backup via USB flash drive and hard drive.
User Manual Chapter 2:Layout 2.1 Panel Buttons (Please refer to actual product for detail) Item Buttons/ Indicators 1 ON/OFF 2 MENU 3 Up 4 Down Marks Functions Turns the screen on or off. ON/OFF Opens the Main Menu screen.
User Manual 2.
User Manual 2.
User Manual 2.
User Manual Chapter 3: DVR Installation 3.1 Hard Drive Installation Caution： Please do not Install or take out hard drive when DVR is running! (1) Remove screws and open DVR upper cover carefully; (2) Insert Power Cord and data cable into Pin of hard drive securely; (3) Put the upper cover back carefully, re-attach screws. 3.2 Camera and Monitor Connection Connect camera cable to video input of DVR, and from video output of DVR to Monitor via BNC connector (Refer to section2.
User Manual Chapter 4: DVR Boot up 4.1. System Initialization After connecting the power adapter the system will boot-up and start initializing. 4.2. Main Interface After initialization, the system will display main interface. When there are video inputs, live images from the cameras will be displayed on screen. You can use mouse to double-click the live image of any channel for full screen display; by double-clicking again, the display will return to display all cameras.
User Manual Chapter 5. DVR Menu 5.1. Main Menu Preview Color set Camera Dwell time display Recording Network Search Playback File List Rec.
User Manual 5.2 Main Menu After clicking right button of mouse, pop-up menu will be displayed on the screen. You can click [main menu] button on pop-up menu to enter into Main menu interface (Shown as Picture 5-2). You can also use the Menu button on the front panel to bring up the window, when using the front panel buttons use the FWD and REW button to move in the menu, and the SEL button to select the icon. You use the ESC button to return to previous window.
User Manual 5.2.2 Record setup Click [Main Menu] [Record] to enter into [Record Setup] menu (Shown as Picture 5-5) Functions： 1、The [Rec Mode] button allows you to setup recording 24 hours, on motion, or on a set schedule. 2、[PACK time] indicates maximum continuous time length of recorded files (15, 30, 45, 60 min). Picture 5-5 The [Record Setup] menu allows you set up recording status (on/off) of each channel, it also allows you setup recording image resolution and quality, and turn audio on/off.
User Manual When selecting DHCP, DHCP server will allocate DVR IP address automatically. When selecting PPPoE, you need to input user and password provided by ISP supplier and set up web port (details please refer to the below picture 5-8). Picture 5-8 When selecting static allocation, you need to setup IP address, net-mask, gateway and web port (shown as picture 5-9).
User Manual 5.2.4 Recording Search Click [Main menu search] to enter into [Video Search] menu (shown as the below picture 5-20). Searched playback: If you input specific date and click [Search], you will find all the recordings for that day. When you select [Date] item, you will playback the recordings in 4 channel mode; or, click [File list] button to display File list interface, where you can playback or backup the file you selected. See File List heading below.
User Manual 5.2.5 Multi player 1、Copy backup file to your PC. 2、Open multimedia player and click [File button Local (F)] to find/select the backup file, and then click [open] Note: the file type you have selected should be *.264 format.
User Manual Recording date and time processing for the current recording file 1 Play 10 All the windows 2 Previous recording file 11 Add window 3 Pause 12 Start 4 Stop 13 Cut 5 Previous frame / Next frame 14 Delete 6 Slow play, Normal play, Fast Play 15 Convert AVI 7 Next Hour 16 OSD 8 Capture picture 17 Mute switch 9 Reduce window 18 Volume adjust 4、Please refer to the below [Video on] setting procedure (System default - video for every channel is on) Setting Video play setting Normal Bar Select the channe
User Manual 5.2.6.1 HDD Management Click [Main Menu Device HDD] to enter [HDD Management] menu (shown as Picture 5-30) Picture 5-30 When you install a HDD, the system will automatically detect if HDD is formatted or not; If HDD needs to be formatted, HDD status will be shown as “Not format”, otherwise, the HDD status will be shown as “Normal” (refer to Picture 5-31) TOTAL SPACE: Indicates total space available on Hard Drive. FREE SPACE: Indicates unused space available on the Hard Drive.
User Manual Email Alarm Notification (to send notice to email account when motion alarm is triggered) Click the [Email setup] menu to enter into its sub menu (shown as Picture 5-33). Picture 5-33 On the [Email setup] mode, refer to its parameter setup shown as picture 5-34 when setting email alarm to “on”. SSL: is a security link transport protocol.
User Manual picture 5-35A. Picture 5-35A 5.2.6.3 PTZ Setup Enter into [Main menu Device PTZ Setup] to select the channel you want to control and set PTZ protocol (Pelco-D or Pelco-P), Baud Rate (1200, 2400, 4800, 9600), Stop bit (1, 2), Parity Check (None, Odd, Even Mark Space), Address Code and Cruise status respectively. Please note the above mentioned channel settings must match the settings of the PTZ camera. Picture 5-36 5.2.6.4 Mobile Click [Main menu Device Mobile] to enter into [Mobile] menu.
User Manual MD AREA: This option allows you select the area you want to be sensitive to motion. The channel is separated into a 13*10 area. When any object moves into the motion detection area, and the area where the object is located is displayed in red recording will be triggered. In the semi-transparent area the motion detection is off. Picture 5-39 5.2.
User Manual 5.2.7.3 Video Setup Click [Main Menu System VIDEO] to setup Video, here you can set Camera system（PAL, NTSC）In the USA we use NTSC. You can also set the resolution for the VGA video out port. Your options are 600x480, 800x600, or 1024x768, or 1280x1024. Picture 5-44 5.2.7.4 Language Enter into [System Language] menu to select the language you want to use on the DVR (shown as Picture 5-45) and click [APPLY] button. The selection will be available after system Auto restarts. Picture 5-45 5.2.
User Manual 5.4 Video Search Click pop-up menu video search to enter into [Video Search] menu you search files and playback recordings. For more information on this operation refer to the previous section 5.24. 5.5 PTZ Control We introduced setting PTZ parameters previously in chapter 5.2.5.3. Here we will discuss how to operate PTZ controls. Click pop-up menu to show PTZ option and enter into PTZ control interface (shown as Picture 5-49).
User Manual Chapter 6: Net-Viewer Program 6.1 Plug-ins download and installation Open IE browser and input IP address and web port of DVR, such as http://172.18.6.202:80/ and confirm to download and install webcam. If your computer is connected to internet, computer will auto download and install the webcam. Reminder: If the webcam is not downloaded successfully, please check if your browser’s safety level or firewall setting is too advanced. Also refer to section 5.2.
User Manual 6.3 Main Interface of Net-viewer Picture 6.3 Log in Net-viewer and show the interface as follows 6.3.1 Menu column (Section 1 on Picture 6-3) 6.3.2 PTZ Control (Numbers 2, 3, 4 on Picture 6-3) 6.3.3 Live Play Control (Numbers 6 through 10 on Picture 6-3) 6.3.1 Menu column (Section 1 on Picture 6-3) Menu column include [Live] menu, [Replay] menu and [Setup] menu and [Logout] menu. 6.3.1.1 Live After Logging-in to system, system will enter into Live display (shown as Picture 6-3). 6.3.1.
User Manual F.F. button: fast forward playback recording Slow button: slow playback recording. Next Frame: play frame by frame. 264 TO AVI button: convert file from H.264 format to AVI format The native format of the backup files is H.264, you can convert H.264 format into more familiar AVI format by clicking the key of 264 to AVI. 6.3.1.3.
User Manual System allows you setup motion detection settings for each channel of DVR remotely (shown as Picture 6-8) Picture 6-8 ③ PTZ Control Click [PTZ control] to setup PTZ cameras. Remote setup methods are the same as local DVR setup. Please refer to Section 5.2.5.3 (shown as Picture 6-9). Picture 6-9 ④ Network Click [Network] to enter into [Network] menu. Remote setup methods are the same as local DVR setup. Please refer to Section 5.2.3. – Network Set.
User Manual 6.3.1.4 Log out Log out of the system. 6.3.2 PTZ Control (Numbers 2, 3, 4 on Picture 6-3) Note: below-mentioned series no will be consistent with the remark no shown as Picture 6-2. ○ 2 .PTZ direction control: Control PTZ moving direction ○ 3 .Zoom, Focus and Iris Control: control direction, zoom, focus and iris of PTZ. ○ 4 .
User Manual Chapter 7: Specifications Model 4CH Video System Compression Format Video Output 8CH NTSC / PAL(Optional) Video：H.
User Manual Chapter 8: Windows Vista User 1、Open IE browse firstly, then enter into Tool bar- 3. and select to appear the below picture: 4. 2、Second, select icon and tick the settings of “ActiveX controls and plug-ins”to Enable, details as follows: Lastly after tick all the “Enable”, please click to exit. At this moment, you could input IP address to run your programme.
Open IE browser and input IP address and web port of DVR…computer will auto downloadand install the widget. We suggest Visita user set user access authority in order to make your PC safer. Setting processing as follows: Click [Start Set Control panel User account] to set user access authority shown as below picture. Remind: If the widgets are not downloaded successfully, please check if your browser’s safety level or firewall setting is too advanced.
Chapter 9: Appendix 9.1 Recording Alarm setting Please refer the below matrix: “⊥” stand for “only alarm but no recording”; “AMR” stand for “alarm recording”; “NLR” stand for “normal recording”; and “NOR” stand for “ no recording”. Once alarm is triggered, alarm icon will occur, and when many alarms are triggered, alarm remarks will occur on the screen.
put into the DVR. Make sure the data cables are attached firmly to the RS485 port on the DVR. 11. Q: Why does the Buzzer keep sounding? A: Please check to see if motion detection is on and the system has detected motion, make sure the hard drive is being detected and has sufficient space available, and that none of your cameras have lost video. You can turn off the buzzer in the Alarm setup option. 9.3 Email server check list（The below info only for your ref.） （Web site） Email address @163.com @vip.163.
9.5 System connection Configuration 4-CH.
The material in this document is the intellectual property of our department . No part of this manual may be reproduced, copied, translated, ٛ transmitted, or published in any form or by any means without our department prior written permission. ٛ Our products are under continual improvement and we reserve the right to make changes without noti ce. But no guarantee is given as to the correctness of its contents. ٛ We do not undertake any responsibility for the harms cause by using our product.
