USER MANUAL Digital Hard Disk Recorder (4/8/16 Channel, MPEG-4) * Default system password: 111111 (for RAMS, Record stop, Menu setup, System off, Auto key lock) * Default ID: admin (for RAMS)
Table of contents 1. SYSTEM OVERVIEWS ..........................................................10 1.1 SAFETY ................................................................................................................................ 10 1.2 COMPONENTS & OPTION ...................................................................................................... 12 1.2.1 Components.................................................................................................................
2.7 PLAYBACK ........................................................................................................................... 28 2.7.1 Press the Play button ........................................................................................................... 28 2.7.2 Audio Play........................................................................................................................... 28 2.8 SEARCH .....................................................................
3.2.3 Channel number .................................................................................................................. 37 3.2.4 Quality................................................................................................................................. 37 3.2.5 Frame rate............................................................................................................................ 37 3.2.6 Record mode .......................................................
3.4.2 Starting Point....................................................................................................................... 50 3.4.3 Audio................................................................................................................................... 51 3.5 DISPLAY SETUP .................................................................................................................... 51 3.5.1 Menu Transparency ...................................................
3.7.6.1 The number of HDD ........................................................................................................................... 64 3.7.6.2 Write Mode ......................................................................................................................................... 64 3.7.6.3 Forced Deletion( Previous few days) .................................................................................................. 64 3.7.6.4 Hard Disk..........................
3.11.2.4 3.11.3 Sample of Search ................................................................................................................................ 73 Still Image Search ............................................................................................................... 73 3.11.3.1 Still Image Search ............................................................................................................................... 74 3.11.3.2 Still Image USB Back up ...........
4.3.10 DVR Setting ........................................................................................................................ 90 4.3.11 Still image Capture.............................................................................................................. 90 4.3.12 Watermark insertion ............................................................................................................ 91 4.3.13 Printing still image ....................................................
4.6.5 Connected screen................................................................................................................110 4.6.6 Search.................................................................................................................................110 4.6.7 Playback .............................................................................................................................111 5 APPENDIX .................................................................
1. SYSTEM OVERVIEWS 1.1 Safety Please follow this . WARNING Please follow instruction to prevent any kind of damage or loss If you do not follow this instruction, it might bring severe damage or loss. The symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the unit.
approved by the party responsible for compliance could void the user's authority to operate the equipment. Warranty will be made void if the product is disassembled or manipulated by the user. Safety Instructions 1) Read these instructions. 2) Keep these instructions. 3) Heed all warnings. 4) Follow all instructions. 5) Do not use this apparatus near water. 6) Clean only with dry cloth. 7) Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
1.2 Components & Option The following items are included with the 4, 8 & 16 Channel DVR. Please be certain that all items are included as soon as you open the box: 1.2.1 Components z DVR (CD-RW is installed as a basic equipment) z Power cable z DSUB-15 connector(2EA) for PTZ /AUX / ALARM (4ch DVR, 1EA) z Quick Manual z Software CD (RAMS, UniPlayer, Quick Installer and Operation Manual) 1.2.
1.
1.3.
1.4 Name, function & connections 1.4.1 Front view 1/9 2/10 3/11 4/12 POWER LOCK REC UP REC 5/13 6/14 7/15 8/16 MULTI SEQ ZOOM PTZ FRZ SEARCH MENU SH-HD REW FF R.PLAY ALARM HDD FULL LEFT OK STOP RIGHT PLAY PTZ DOWN PAUSE < 16ch DVR > 1 2 3 4 POWER LOCK REC UP REC 5 6 7 8 MULTI SEQ ZOOM PTZ FRZ SEARCH MENU SH-HD REW FF R.
Description: 1. CD-RW z Easy backup by CD-RW is available. The cover of CD-RW shows an excellent design. 2. LED Display z POWER : During Standby mode, red light on, during running unit, green light on z REC : During recording green light flashes z ALARM: Green light (Alarm triggered) z HDD FULL: Green light (No more disk space for recording) z PTZ: Pan, Tilt, Zoom, Focus status is indicated by Green 3.
This button also can be used for all motions area release purpose on motion detection set up menu. z SEQ(8ch DVR) : Sequential view under live mode. Viewing of all active video input channels sequentially. If you click “SEQ” button one time, each single channel can be viewed sequentially. If you double click “SEQ” , it views 4, 8, 9 screen divisions. This button also can be used for all motions area release purpose on motion detection set up menu. z SEQ(4ch DVR) : Sequential view under live mode.
z MENU: Press button to access Main Menu. Press again to return. 5. Direction/select button z UP: Used to move the cursor up; change possible values in the setup menu; under PTZ control sub menu, used to move camera; or used to adjust focus. z DOWN: Used to move the cursor up; change possible values in the setup menu; under PTZ control sub menu, used to move camera; or used to adjust focus. z LEFT: Used to change possible values in the setup menu.
1.4.2 Rear panel view CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN IN OUT < 16ch DVR > CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN IN OUT < 8ch DVR > CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN IN OUT < 4ch DVR > 4 & 8 & 16 Channel DVR Operation manual Revision 1.
Description: 1. USB z Connect USB flash drives for backing up stored video files (8/16ch DVR only) 2. ETHERNET z Network terminal for 10Base-T (RJ-45) 3. PTZ/AUX/ALARM z Terminal for PTZ, sensor, alarm, and AUX IN/OUT (DB-15 Male Connector) (4ch DVR has one only.) 4. VGA and SERIAL z VGA : Terminal for VGA video output (DB-15 Male Connector, 4ch DVR has an option on this) z Serial terminal for RS-232C (PC) for console or quick installation (DB-9 Male Connector) 5.
1.4.3 Remote controller function ① POWER : button for power on/off. (DVR should be standby or on working status) ② RECORD : button for forced recording (If it’s pressed again, recording stops) ③ INFO BUTTON GROUP : button group for HDD, NET, LOG, INFO. If each button is pressed, the relative information shows and press Menu button for exit ④ LOCK : Remote control lock button. Same function as Lock button in the front panel. To unlock, press any button and input password.
⑥ Up/down, Right/left & OK button Status OK Up/down Right/left Menu Selection, sub menu Menu move x Sub Menu Selection Move Menu Adjust value Play x Channel Coverting Low speed and playback speed ⑦ DVR : Reserved. ⑧ MENU : Button for menu. Various sub menu can be selected - To exit, press again the button ⑨ Functional Key Group : A group for “PTZ”, “FRZ”, “ZOOM” “OSD” from the left. Remote control, Rock button. Same function as Lock button in the front panel.
1.5 INSTALLATION 1.5.1 Installation and connection 1/9 2/10 POWER LOCK REC UP 3/11 4/12 5/13 6/14 7/15 8/16 MULTI SEQ REC ZOOM PTZ FRZ SEARCH MENU SH-HD REW FF R.PLAY ALARM HD D FULL LEFT STOP RIGHT PLAY PTZ 1/9 2/10 POWER DOWN PAUSE LOCK REC UP 3/11 4/12 5/13 6/14 7/15 8/16 MULTI SEQ REC ZOOM PTZ FRZ SEARCH MENU SH-HD REW FF R.
1.5.1.1 Camera 16 Channel(16ch DVR): The unit comes with 16 video IN for up to 16 cameras connection. In order to use Loop-Through, please enter into DVR setting menu and set up Termination (through Y-cable or T terminal). 8 Channel(8ch DVR) : 8 cameras can be connected. The below video connectors are for Loop through. 4Channel(4ch DVR) : 4cameras can be connected. The below video connectors are for Loop through 1.5.1.
1.5.1.3 Audio Use IN for a Line input and OUT for speaker output. IN OUT 1.5.1.4 RS-232 Use this connector to connect RS-232 cable to the serial port on your PC to control the DVR or to perform Quick Installation. 1.5.1.5 PTZ/AUX/ALARM 1.5.1.5.1 RS-485+, RS-485DVR uses RS-485 protocol to control PTZ Receiver, Speed Dome, and Auto-focus camera. Be sure to match the polarity. 1.5.1.5.
1.5.1.5.4 Sensor (16ch DVR :1~16, 8ch DVR:1~8, 4ch DVR:1~4) Users can connect up to four N.O./N.C. type sensors(4 for 4ch DVR, 8 for 8ch DVR, 16 for 16ch DVR) and configure them within Main Menu, Sensor Setting. 1.5.1.6 Network Support 10 base-T Ethernet, and connect Ethernet cable. 1.5.1.7 USB flash memory Perform backup of recorded video files from DVR system to USB flash memory manually. 4 & 8 & 16 Channel DVR Operation manual Revision 1.
2. Basic operation procedures 2.1 Power On/Off 2.1.1 Power ON Using either the keypad or the remote control, press the “POWER” button. (Note: In case of power outage or rare instance of system failure, the DVR will reboot automatically) The Power LED light will turn from red to green when it has turned on properly. In a standby mode, the LED is red. 2.1.2 Power OFF In order to shutdown the system, you must type in the password. The default password for shutdown is “111111”. 2.
2.5 Network setting There are three types of network setting for the DVR: STATIC, DHCP, or PPPoE. Please set the network type. (Network Setup in Main Menu) 2.6 Recording Select recording related parameters in the Record Setup in the main menu. 2.6.1 Recording types Enter in Recording setup of menu. For resolution, select either 720*240 (NTSC), 360*240 (NTSC) or 720*288 (PAL), 360*288 (PAL). Audio channel is synchronized with the selected video signal.
2.8.2 Search method z Calendar Search When you press Search, select from three options listed: Among these three options, select calendar mode.(Click “OK” button) Then “Year, Month, Date” will be shown on the screen , when you click each one, hour and minute column will be shown accordingly. Then you can view all selected recorded file at the same time. z Event Search When you press Search, select Event Search from three options listed.
2.10 Client Program 2.10.1 RAMS (Remote Access & Monitoring System) z Remotely access, monitor, and operate the DVR for real-time live viewing, playback, backup, on-the-fly recording, and control over the LAN/WAN z Upgrade the S/W(Kernel, Ramdisk) of DVR z Install the RAMS program as referred to in section 4.2 of Operation Manual. z Execute RAMS program and register selected DVR’s IP address & Port number from the DVR list by clicking following button z .
3 Main Menu screen Figure. 3-1 Main Setup screen 3.1 Camera Setup menu Figure. 3-2 Camera setup screen 4 & 8 & 16 Channel DVR Operation manual Revision 1.
3.1.1 Channel A user can select targeted camera. After setting this, live viewing picture will be changed to selected channel automatically. 3.1.2 Camera Name Figure. 3-3 Camera name edit screen User can edit camera name indicated button part of each channel. as explained paragraph 3.1.1. According to above picture 3-3, after keyboard type’s window which is enterable or editable as displayed, user can set channel name with entering new letters and it is available 12 letters at maximum.
Key Explanation Direction Key Move the button OK Click selected button 0~9 Figures Input Figures SEQ ‘.’ Input MULTI Capital letter & Small letter(CAPS) PLAY(▶) Input Space R.PLAY(◀) Input back space MENU Move to “OK” Button Meaning of Key 3.1.3 Camera hide User can make the live screen appear or not by channel with this function. If user sets up “ON” in this function, the live screen of the selected channel does not appear.
3.1.4.1 Contrast, Brightness, Hue, Contrast, Brightness, Hue will be managed & each parameter has 16 level steps adjustable. 3.1.4.2 Default Users can restore the factory default setting of Contrast, Brightness & Hue. Confirmation box on picture setting default will appear after entering default. User can restore the factory default setting after entering ‘YES’ key button. Figure. 3-5 Confirmation box on Picture Setting Default 3.1.5 PTZ setup Figure.
It sets PTZ protocol of targeted channel in the Camera Setup. (Please refer to paragraph 3.1.1 for channel selection) 3.1.5.1 Model No Select the PTZ model or choose “NONE”. 3.1.5.2 PTZ ID Set the PTZ ID: 0 ~ 255 The PTZ ID must match the ID number that has been set by the PTZ Controller. Please verify the ID on the Controller first before setting the PTZ ID. 3.1.5.
Figure. 3-7 Additional PTZ Menu - Go to Preset : To move the Pan/Tilt drive to the position preset in Set Preset mode. Preset numbers are selected by Left/Right buttons and the Pan/Tilt drive moves to the preset position after pressing OK button. - Set Preset : To preset the position of the Pan/Tilt drive. Users can preset 1-99 positions selected by Left/Right buttons and save the preset by pressing OK button. - Iris : To open/close the camera lris by Left/Right buttons.
3.1.8 Loop Through Setup Set up Loop Through function. Set up is available with 75 or high each channel. 3.2 Record Setup menu Figure. 3-8 Record setup screen 3.2.1 Resolution Resolution for NTSC is “360 x 240” or “720 x 240”. PAL is “360 x 288” or “720 x 288” selectable and selected resolution will be applicable to all channels simultaneously. 3.2.2 Audio Sync As audio input port is one channel available, user should synchronize audio signal with targeted video signal.
But, with 720 x 240 (NTSC), 720x288 (PAL) resolution, user should not set to exceed 60(NTSC), 50(PAL) frame per second with accumulated total channel recording. 3.2.6 Record mode User will choose recording mode channel by channel and selectable parameters and meaning are below. z Manual: Manual recording function that starts record and/or stop recording manually by pushing REC key on remote controller or on front key.
3.2.7 Record Schedule Setup Figure. 3-9 Recording schedule setting screen User can select to set recording schedule targeted date, time based week & 24Hours. Move the cursor to the desired position of time by pressing up/down key and set the recording mode at the desired position of time by pressing the OK button with referring to the Help Message per Record Mode on the right position. After the setup, store the set schedule and exit to the top menu by pressing the Menu button.
3.3 Event Setup Menu Figure. 3-10 Event Setup screen 3.3.1 Motion Detection Setting Figure. 3-11 Motion Detecting Setup screen Sets up the motion detecting area and sensitivity. 4 & 8 & 16 Channel DVR Operation manual Revision 1.
3.3.1.1 Channel Sets up the motion detecting area and sensitivity for each channel. 3.3.1.2 Sensitivity Sets up the motion detecting sensitivity. The lower the sensitivity gets the closer to the left the red bar gets. 3.3.1.3 Detection Zone Figure. 3-12 Motion Detecting Area Setup screen Selects the motion detecting area. The sky blue square implies the current cursor and the yellow square implies the area that was already selected as the motion detecting area.
3.3.2 Sensor Setting Figure. 3-13 Sensor Setting screen 3.3.2.1 Sensor Type N.O.: Normal Open. Operation mode for the installed sensor’s contact point is usually open in normal condition and changed from open to close at sensor’s detect event. N.C.: Normal Close. Operation mode for the installed sensor’s contact point is usually close in normal condition and changed from close to open at sensor’s detect event. 3.3.2.2 Channel Link Assign sensors to designated Camera Channels.
3.3.3 Alarm input/ Output Figure. 3-14 Alarm Output Setting 3.3.3.1 Sensor Configure the alarm out on/off activated by the sensor. 3.3.3.2 Motion Configure the alarm out on/off triggered by the motion detection. 3.3.3.3 Relay Time Configure the alarm duration time. It can be set up from 0 second to 60 seconds in the unit of 5 seconds. 3.3.4 Post Alarm Record Time Configure the recording continuation time after starting an event recording.
3.3.5 FTP Setting Figure. 3-15 FTP Setting Enables the unit to transmit an assigned FTP Length of Motion picture to an FTP Server over network when an event occurs. The event will be transmitted 15 seconds after the event occurs. 3.3.5.1 FTP Server IP address If you click ftp address , key board shaped will turn on the screen. Put the suitable server address (ref.3.6.4.6(STATIC) & 3.6.6.
3.3.5.2 ID Configure the FTP ID. The ID can contain maximum of 31 characters. Figure. 3-16 FTP ID 3.3.5.3 Password Configure the FTP password. The password can contain maximum of 12 characters. Figure. 3-17 FTP Password input 4 & 8 & 16 Channel DVR Operation manual Revision 1.
3.3.5.4 Target Path Configure the path to transmit to an FTP server. The path can contain maximum of 31 characters. Figure. 3-18 FTP Target Path 3.3.5.5 FTP Length of Image (second) Select FTP length of image by second (5 to 10 seconds are selectable) to transmit image files for selected seconds. 3.3.6 FTP Trigger Setting Selects on/off for transmitting the video file to FTP for each channel. 4 & 8 & 16 Channel DVR Operation manual Revision 1.
Figure. 3-19 FTP Trigger Setting 3.3.6.1 Sensor Configure sensor events. 3.3.6.2 Motion Configure motion events. 3.3.7 E-Mail Address Setting Transmits the content of an event log periodically through e-mail. Configure up to four e-mail address to transmit under event status simultaneously. You can set up to 4 person’s addresses and e-mails will be sent to all of these four at one time.
Figure. 3-20 E-Mail Address setting 3.3.8 E-Mail Setting Figure. 3-21 E-Mail Setting 3.3.8.1 Send (Period) Configure the e-mail transmitting cycle. It does not transmit when it is set to NO. The setting time can be set up at the units of within 2 minutes after event, 30minutes, 1, 2, 5, 12, 24 hours. 4 & 8 & 16 Channel DVR Operation manual Revision 1.
3.3.8.2 Prohibition setting Set up prohibition time to transmit the e-mail. Users can enter prohibition time from the starting time and the ending time of transmitting the e-mail 3.3.8.3 SMTP Server IP address If you click ftp address , key board shaped will turn on the screen. Put the suitable server address (ref.3.6.4.6(STATIC)& 3.6.6.4(PPPoE)) If you want Domain name instead of IP address under PPPoE, STATIC , a suitable DNS server address should be at the network setting menu.
Figure. 3-22 Event Log Display screen 3.4 Playback Setup Figure. 3-23 Playback setup screen 3.4.1 Channel Designate the channel to be viewed when the “PLAY” button is pressed. 3.4.2 Starting Point This starting point configures the starting position when the “PLAY” button is pressed. z FIRST: This can search for and replay the oldest recorded images from the selected channel. 4 & 8 & 16 Channel DVR Operation manual Revision 1.
z 30Min/1HOUR/6HOUR/12HOUR/24HOUR AGO: This can search for and replay the previous recorded images from the selected channel. 3.4.3 Audio If the recorded files contain audio, choose whether to turn the sound ON/OFF During playback. 3.5 Display Setup Figure. 3-24 Display setup screen Determine whether to have the following be shown on the monitor: Camera name, Time/Date, HDD status, Borders. Select either ON/OFF for each item. 3.5.1 Menu Transparency OSD MENU Transparency decision.
3.6 Network Setup Menu Figure. 3-25 Network Setup screen 3.6.1 DDNS setting Set up DDNS (Dynamic Domain Name System) server address & port number. Users can set up two DDNS server address and port, for the faster setting jog shuttle can be used, too. Figure. 3-26 DDNS setup screen 4 & 8 & 16 Channel DVR Operation manual Revision 1.
Under DHCP or PPPoE configuration using IP Router, the DVR will receive an IP address periodically, and each time, the IP address can be different. Therefore, in order for users to access the DVR over the network, it must update its IP address to the DDNS Server. Under IP router configuration, IP of DVR must be setup as static IP address and it must update its IP address to the DDNS server. Therefore DDNS Link on NETWORK SETUP menu should be on.
Figure. 3-27 Remote Connection Login Password screen 3.6.3 Network Type Choose one type from the following: STATIC, DHCP, & PPPoE. Static mode uses fixed assigned IP address in the network. DHCP (Dynamic Host Configuration Protocol) receives an IP address from the DHCP Server, and it may change according to the lease period. PPPoE (PPP over Ethernet) mode is used for network using PSTN such as ADSL. Please refer to paragraph 3.6.3.1, 3.6.3.2, 3.6.3.
3.6.4 STATIC Figure. 3-28 STATIC Network setting 3.6.4.1 DDNS Link On/off You can decide if you want to use Dynamic DNS or not under static network type with on/off button. 3.6.4.2 Port Configure the Port number to be used to connect to the DVR system using RAMS (Remote Access & Monitoring System). The default Port number is port 80. Change easily by using Jog/shuttle equipped in front panel. 3.6.4.3 IP Address Assign a fixed IP address to the DVR.
3.6.5 DHCP Figure. 3-29 DHCP setup screen 3.6.5.1 Port Please refer to paragraph 3.6.4.2 for Port setting of STATIC. 3.6.6 PPPoE Figure. 3-30 PPPoE setting 4 & 8 & 16 Channel DVR Operation manual Revision 1.
3.6.6.1 Port Please refer to the port setting in paragraph 3.6.4.2 3.6.6.2 ID Type in your user ID for the ADSL account (PPPoE). The password can contain maximum of 31 characters. Figure. 3-31 ID input screen 3.6.6.3 Password Type in your user Password for the ADSL account (PPPoE), The password can contain maximum of 12 characters. Figure. 3-32 Password input screen 4 & 8 & 16 Channel DVR Operation manual Revision 1.
3.6.6.4 DNS IP Setting DNS address of DVR currently used. You can use jog shuttle or number button at front panel. 3.6.7 Changing the Network configuration If users want to change network type of DVR, users must reboot the system. User can restart the new network mode setting after entering ”YES” key button. Figure. 3-33 Changing the Network setting screen 3.7 System Setup screen Figure. 3-34 System Setup screen 4 & 8 & 16 Channel DVR Operation manual Revision 1.
3.7.1 DVR Name Type in the name of the DVR you wish to assign. The name can contain maximum of 12 digits. Figure. 3-35 DVR name screen Using the arrow, type in the DVR name. Click “OK” when finished. 4 & 8 & 16 Channel DVR Operation manual Revision 1.
3.7.2 System Password Figure. 3-36 System password set up Set up part for system password, related function and application. This is a part of installation, actual system password, related function and password application. 3.7.2.1 Password Setting To change system password: First, type-in the current password, confirm. Then if it is correct, type-in the new password twice. If they match, the password has been changed. Users can use any numeric number from 1~8, combined 6 units.
Figure. 3-37 Password input screen 3.7.2.2 Password Apply Determine whether the system password has to be applied to power On/Off. The applicable features are recording close, enter menu, system off. Users can set up password ON/OFF for each feature. Setting to On, when each feature starts, users have to confirm password for each step. Setting to Off, users can use any confirmation of password. 3.7.2.3 Auto Key Lock Possible Setting time is every 30sec, 1 min, 3min, 5min, 10 minutes.
Figure. 3-38 Set up Time/Date 3.7.3.1 Set up Time / Date Set up date and time on the system 3.7.3.2 Time / Date Format Set up format for date and time. There are two types of time: 24hr circle/ 12hr circle. Date format can be set up as the following: YYYY/MM/DD, MM/DD/YYYY, DD/MM/YYYY. 3.7.3.3 Day Light Saving Time Set up Start Day and End Day in Day Light Saving Time mode For example, if users adopt day light saving time from May 01 to Oct.31, input the dates accordingly. 3.7.3.3.
3.7.4 Buzzer Users can turn the buzzer ON/OFF depending on the situations. Usable situation is Sensor, Motion, & Video Loss. When users activate the buzzer, buzzer will make a sound when there any event occurs. There would be no sound if the buzzer is turned Off. Figure. 3-39 Set up buzzer 3.7.5 Language Six Languages (English, Korean, Japanese, Spanish, French, Germany) are available. 3.7.6 HDD Setup Set up for Internal HDD and Removable HDD, See the information.
Figure. 3-40 HDD Setup image 3.7.6.1 The number of HDD Show the HDD quantity that is built –in. 3.7.6.2 Write Mode Set up writing type in recording. Types are ‘Once’ and ’Overwrite’. If set up by ‘Once’, HDD can record until the Full state. If set by ‘Overwrite’, HDD will record continuously by start overwrite oldest data. 3.7.6.3 Forced Deletion( Previous few days) The images recorded earlier than specific date can be erased by force. The number of dates for erasure can be selected from 1 ~ 100.
3.7.6.4 Hard Disk 3.7.6.4.1 Capacity Indicate the used part and total capacity of Internal HDD. Used part of HDD (GB) / Full capacity of HDD (GB) 3.7.6.4.2 Format This is function for internal HDD formatting and you must reboot the system after this instruction. Confirmation box on format will appear after entering format key. User can format and erase all information of HDD, after entering “YES” key button. Figure. 3-41 Confirmation box for HDD format Max 2 HDD can be installed.
3.7.7.1 Active Set up Active state. Low/High will be different depend on machine.. 3.7.7.2 Function The following list contains a brief description of each function. 3.7.7.2.1 Direction : IN z UNUSED: Do not use the AUX port. z ALARM RESET IN: Pause alarm or buzzer when event occurred z RECORD START IN: Record is on while external signal comes in. z RECORD ON/OFF: Recording start/stop during user push the button & same as pushing remote controller or DVR machine 3.7.7.2.
Figure. 3-43 Confirmation box for Factory Default 3.7.9 Software Upgrade Users can upgrade the software of Ramdisk and Kernel using the USB flash drive (thumb drive) by the following steps. - Get the latest version of software (Ramdisk/Kernel) from distributor - Copy the downloaded files from the PC to the USB memory. - Connect the USB memory to the USB port. - Go to 'System Setup' then 'S/W Upgrade' then select Ramdisk or Kernel to upgrade. Figure.
- After the unit recognizes the USB flash drive and upgrading end, the unit will reboot. Figure. 3-45 Ramdisk Upgrade 3.8 Backup Backup recording data to CD-RW or USB Flash Drives Figure. 3-46 Backup screen 3.8.1 Backup Device Set up the device for backup. USB / CD-RW are available 3.8.2 Start Time Input the start of backup date and time. 3.8.3 End Time Input the end of backup date and time. 3.8.4 Channel Choose the channel to backup. 4 & 8 & 16 Channel DVR Operation manual Revision 1.
3.8.5 Event Choose the event to backup. In case of none mode, selected files according to time will be backed-up. 3.8.6 Backup Start Based on the input date, time, channel and event & other condition search the images will be backed-up to the chosen device. Back up progress rate is marked on the bottom right side of the screen. 3.8.7 Format This menu is used only when backup device is CD-RW. In case that backup device is CDRW, format command has to be done by this menu, before starting backup.
3.10 System Information Figure. 3-48 System Information 3.10.1 Video type It shows that present Video type of System is NTSC or PAL. 3.10.2 H/W version It shows the H/W Version of system. 3.10.3 S/W version It shows the S/W Version of system. 3.10.4 KERNEL version It shows the S/W Version of KERNEL. 3.10.5 Mac Address It shows Mac Address of system. 3.10.6 Audio Shows audio part availability. 3.10.7 Language Shows supporting language. 4 & 8 & 16 Channel DVR Operation manual Revision 1.
3.11 Search Menu When you click ”SEARCH” button below screen will be shown on the screen. Figure. 3-49 Main Screen of Search 3.11.1 Search by Calendar Figure. 3-50 Search by Calendar 4 & 8 & 16 Channel DVR Operation manual Revision 1.
3.11.1.1 Calendar View When you click specific date and time , it will be showing recorded data as drawing. 3.11.1.2 Drawing Color Figure. 3-51 Calendar Search Screen z Red : Enforced Recording z Green: Motion Event Recording z Purple: Sensor Event Recording z White : No Recording 3.11.1.3 Hour( Time) It is composed of 24hours. Recording status can be distinguished by color.
3.11.1.4 Display by minutes If there are some recording on a specific time and channel , it shows suitable color on a specific minute time zone. 3.11.2 Search of Event It shows event occurring time. 3.11.2.1 Start time Key in the time you would search from 1970 to 2037(No more or less than that) 3.11.2.2 Ending Time Key in the time you would search from 1970 to no more 1970 to 2037. 3.11.2.3 Select the channel Select the channel you want to look at. 3.11.2.4 Sample of Search Figure.
3.11.3.1 Still Image Search 3-53 Still Image search Screen 3.11.3.2 Still Image USB Back up Click the specific file and push “PLAY” button , still image will be copied. 3.11.3.3 Converting Still image file into JPG format. - Execute simpleplay_m4.exe.file - Open the file to change into jpg - Click the second disc button of Toolbar menu #2 and save it as jpg or bmp type. 3.12 PLAYBACK 3.12.
3.12.1.2 Screen of played back. Figure. 3-51 Screen of playback 3.12.1.3 Control during play back 3.12.1.3.1 Stop of Play back If user needs to stop playback, user should press button “STOP” in the remote controller of in the system, and play back stops and live screen is coming back. In case of calendar search , “SEARCH“ button let it turn to previous search screen. 3.12.1.3.2 Temporary Stop during Playback In order to stop temporarily playback, press button “PAUSE”.
3.12.1.3.4 Change of Direction of Playback There’s forward and Backward directions. In order to change direction from Forward to Backward, user press the button “REVERSE PLAY” and backward playback starts with normal speed. On the contrary, to change direction from Backward to Forward, user press the button “PLAY” and Forward playback starts with normal speed. 3.12.1.3.5 Select of channel of Playback This function is to change the other channels during the same time .
3.12.2.2 Screen of playing back Figure. 3-52 Still Image of playing back 3.12.2.3 Control during Still Image Play back 3.12.2.3.1 Stop of play back To stop the playing back, User press button “STOP” or “ SEARCH”. Playback stops and screen of search list appears. 3.12.2.3.2 Next screen Press Button “RIGHT” and next screen is played back. 3.12.2.3.3 Previous screen Press Button “LEFT” and previous screen is played back. 4 & 8 & 16 Channel DVR Operation manual Revision 1.
3.13 Miscellaneous Menu Figure. 3-53 Miscellaneous Menu This menu is to use the five functions that are placed only on the remote control but on the keypad of the unit. 3.13.2 NET Displays the current network IP and the user connected to the network. (It substitutes the NET button on the remote control). 4 & 8 & 16 Channel DVR Operation manual Revision 1.
Figure. 3-547 Network Information 3.13.3 OSD Turns on/off the OSD (On Screen Display). It substitutes the OSD button on the remote control. 3.13.4 Audio Mute Turns on/off the audio. It substitutes button on the remote control. 3.13.5 HDD Displays the HDD information. It substitutes the HDD button on the remote control. 3.13.6 LOG Display the System Log. It substitutes the LOG button on the remote control. 4 & 8 & 16 Channel DVR Operation manual Revision 1.
4 Client program 4.1 Overview of DVR z RAMS_M4 (Remote Access & Monitoring System MPEG4) is used to remotely access, monitor, and operate the DVR for real-time live viewing, playback, backup, on-the-fly recording, and control over the LAN/WAN. z UniPlayer_M4 is a viewer with functions for recording, capturing, & backing up files. z QuickInstaller_M4 is a setup configuration template for quick & easy, multiple unit setup using RS-232 or network.
4.3 RAMS_M4 (Remote Access & Monitoring System Mpeg4) 4.3.1 Screen and button ① Screen capture button, Video record button ② Screen display ③ Channel display button, Sound control button ④ If logo is clicked, program version window appears.
4.3.2 Connecting to DVR Click icon to open the DVR list. ① This box allows the user to select the IP address assigned to the selected unit. This is required for making a network connection. ② To create a new IP address & DVR selection, enter the DVR name, DVR address, and port number. ③ To Click to add the newly entered DVR information into the DVR list ④ After selecting a DVR Name from the list and making changes, click Modify to update the changes made to the item.
4.3.3 UniPlayer_M4 link If you click this button on main menu, UniPlayer_M4 program will be executed. Regarding the UniPlayer_M4 program, please refer to the article 4.3 4.3.4 Full-screen display If you click button on the main menu, you can see full screen pictures. If users press the key of ESC, you will return to the selected screen. OSD in the screen is same as that of DVR (Channel name, recording on/off, Motion icon, Sensor icon) 4 & 8 & 16 Channel DVR Operation manual Revision 1.
4.3.5 Program setup If users click this button in the main window, window of program setup appears. ① Capture a still image and select a folder where the image is recorded ② Select the image of water mark to be input in the still image ③ Set up a program by user’s language ④ Set up whether alarm occurrence is on or off when motion detection or sensor icon activated. ⑤ Close the window without saving the setup ⑥ Close the window after saving the setup 4.3.
=> DVR (live viewing) => DVR (Recording mode) 4 & 8 & 16 Channel DVR Operation manual Revision 1.
4.3.7 DVR playback search This button is used for playback search, playback, and backup functions for DVR and after logging in by admin. ① Enter search time from start time to end time ② Check if user want to search event condition ③ Select targeted channel for search ④ Close DVR playback search ⑤ Start to search by selected searching condition ⑥ Previous research result will appears 4.3.8 DVR playback search Search data will appear list form if users push two buttons at DVR playback screen.
① DVR search files will appear recording start/end time, channel, and event information included ② Button for staring of backup. With pushing selected channel, start to playback. Start to playback after pushing selected channel,. If do double click selected files, it starts to playback. ③ Close DVR backup window After selecting a file at list, push play button or do double clicks in order to watch playback pictures. 4 & 8 & 16 Channel DVR Operation manual Revision 1.
① Change present mode to playback mode ② Display playback picture derived from DVR system ③ Button for reverse playback, pause, still, reverse phase, forward phase, slow, fast, previous search, next search ④ Comeback playback mode to Live viewing mode Reverse playback button Playback button Temporarily pause button Still image button When user use temporarily pause image file move to backward When user use temporarily pause image file move to forward Play stored files slowly.
Play stored files quickly. User can control by clicking this button 4.3.9 DVR backup ① DVR search files will appear recording start/end time, channel, and event information included ② Indicator backup progress at backup ③ Button for staring of backup.
4.3.10 DVR Setting This button is for linking into quick installation program, which is used to manage setting parameter of DVR easily. It can be activated after logging in by admin. The setting parameter of DVR are displayed. 4.3.11 Still image Capture Yon can save playing image such as live viewing image, DVR playback image, into still image by capture. Besides users can capture image by pushing capture button for each channel or push capture button at the foot of a screen.
① Select check box in order to insert watermark into still image capture ② Save still image as user defined default file name if chosen ③ Save still image as user selected new file name if chosen ④ Insert keyword to user easy searching ⑤ Close still image capture window ⑥ Print still image capture file ⑦ Save still image. The destination of recording is assigned at still image recording, folder through setup menu among RAMS_M4 program 4.3.
① Select the targeted channel changed recording time. ② Continuous recording until clients stop recording mode ③ Continuous recording until targeted minutes. Of course, it stopped manually by users ④ Continuous recording until targeted date & time.
4.3.16 HDD Information Orange: used parts of HDD, White: remaining par of HDD. Detailed HDD information will be activated on pushing this icon. ① Select hard disk ② It shows total capacity of HDD ③ It shows the used capacity of HDD used ④ It shows the capacity of HDD to be used ⑤ It shows the capacity of HDD used and to be used ⑥ Close the window 4.3.
③ Display S/W update window of DVR system 4.3.18 S/W upgrade of DVR S/W upgrade window is activated on pushing S/W upgrade button in the program version check screen ① : Select targeted files to upgrade ② : Select targeted files saved in local PC ③ : Enter targeted DVR information such as DVR address, Port, user, and password (admin only) ④ : Indicator of targeted file’s transmission status ⑤ : Close upgrade window ⑥ : Transmit targeted files.
4.3.19 Program minimizing Rams_M4 program is minimized 4.3.20 Close program Closed Rams_M4 program 4.4 UniPlayer_M4 4.4.
⑩ Button for user searching ⑪ Button for directory based searching ⑫ Retrieve button for watermark, printing, Capture ⑬ Button for sound On/Off, volume adjustment ⑭ Button for minimizing ⑮ Button for closing program 4.4.2 Search Users access to search files after push this icon. As files are default mode, without knowing of files, users can access it. 4.4.2.
=> If there is nothing to special condition for searching, all files saved in recording folder will be displayed on search window after searched. => Search window after selected channel number 1 as search option. 4 & 8 & 16 Channel DVR Operation manual Revision 1.
4.4.2.2 Search option for still image ① Enter targeted recording date for search ② Enter targeted DVR name for search ③ Enter targeted channel ④ Enter keyword to classification to list ⑤ Start to search accordingly ⑥ Close search option window => If there is nothing to special condition for searching, all still images saved in folder will be displayed on search window after searched. 4 & 8 & 16 Channel DVR Operation manual Revision 1.
=> Search window after selected channel number 1 & selected date (Jun. 28, 2006) as search option. 4.4.3 Searching by directory You can use it when you know the directory has AVI file or still image file. It will be set up default directory at first. After that users can choose their own directory than see all folder user want to save will be on the list. 4 & 8 & 16 Channel DVR Operation manual Revision 1.
=> AVI file Playing screen by searching scene 4.4.4 Still Image Capture Save replaying images into still image by capture. Besides users can capture image by push capture button for each channel or push capture button at the foot of a screen. 4 & 8 & 16 Channel DVR Operation manual Revision 1.
Still image will be saved in a path of which is established in RAMS_M4’s setup section screen ① Select check box in order to insert watermark into still image capture ② Save still image as user defined default file name if chosen ③ Save still image as user selected new file name if chosen ④ Insert keyword to user easy searching ⑤ Close still image capture window ⑥ Print still image capture file ⑦ Save still image.
Playing image file Temporarily pause image file Pause When user use temporarily pause image file, move to backward When user use temporarily pause image file, move to forward. Play file slowly. Users can control by click this button. Play file quickly. User can control by click this button. 4.4.8 Water mark drawing When still image is display, if push this button watermark will be drawn. If you find other color except black, white, blue color, image file must get damaged.
=> Still image Display screen. Push this button , water mark will be drawn. Ö Watermark viewing screen. If you find other color except black, white, blue color, image file must get damaged. 4 & 8 & 16 Channel DVR Operation manual Revision 1.
4.4.9 Panorama You can see the panorama screen when you push this button while file playing. (Button will change into like this button. . And & button can help user to view screen while control screen back and forth. And click the one screen which is one of the 16 channel, you can see 640x480 image. If you want to come out of the panorama mode, click button. Then program will go back to former state. => Screen in panorama mode. 4 & 8 & 16 Channel DVR Operation manual Revision 1.
=> Image when click one screen in panorama mode. 4.4.10 Check the program version. Click right part of logo to confirm version. 4.4.11 Program minimizing UniPlayer_M4 program is minimized 4.4.12 Close Program Close UniPlayer_M4 program 4 & 8 & 16 Channel DVR Operation manual Revision 1.
4.5 Quick Installer 4.5.1 Select model Clicks to select DVR model name and video type in order to set system parameters. 4.5.2 System parameter setting * Right parts on System parameter setting window is same form as Main menu used in DVR system. Users can change DVR system parameter by entering each menu. * Main menu description * File ->Open: Read to display saved parameter values from DVR system. 1. File ->Save: Click to save setting parameter values as file. 2.
parameter values 4. System parameter-> Write parameters to DVR: Transfer to save setting parameters of DVR. 5. System parameter->Default value setting: Initialize parameters values. 6. Communication->Network: Communicate data through network. 7. Communication->Serial: Communicate data through serial port (Setting preferable Com Port) 8. Language: Click to select preferable language 9. Information: Click to display program version information. 4.5.
communication between DVR using serial port. 4.6 Connection by Internet Explorer 4.6.1 Security setup In “Internet Option” Menu, Choose “Trusted sites” then click “Sites…” button, 4 & 8 & 16 Channel DVR Operation manual Revision 1.
Your DVR address Add your DVR Address.(it possible “IP” or “MAC”). 4.6.2 Download ActiveX control In order to download ActiveX control, press “confirmation” button, when the message Appears, and download in the PC. (If “cancel” button is clicked, program may not be worked) 4.6.3 Connection with DVR Fill the address of DVR Mac address or IP up in the address window of Internet Explorer. 4.6.4 Login Fill network password of DVR and press “OK” button, same as Rams_M4 program.
4.6.5 Connected screen 1. In the lower part of screen, there are buttons - button to select the screen division & button to search the moving picture.. 2. In the right part of screen, there is a button to control PTZ. - PTZ control is available when one screen is selected, - In order to select one screen, double click the required channel. 4.6.6 Search 4 & 8 & 16 Channel DVR Operation manual Revision 1.
Same function as search of DVR playback search Please refer to the article 4.3.7 4.6.7 Playback This is the screen when it’s playback.. Playback control button in the right parts has same function as DVR playback in RAMS_M4. Please refer to the article 4.3.8 (DVR manual) 4 & 8 & 16 Channel DVR Operation manual Revision 1.
5 Appendix 5.1 Installing HDD 5.1.1 HDD Install Methods 2 HDD can be installed for 8/16ch DVR. In case that 1 HDD is installed, HDD should be set to “MASTER” or “SINGLE” mode. In case that 2 HDD are installed, one HDD should be set to “MASTER” and the other to “SLAVE” mode. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN IN OUT z Unlock all those Volts of “ A” with drivers. 4 & 8 & 16 Channel DVR Operation manual Revision 1.
z When You lift up the back part of TOP COVER, DVR unit can be separated into TOP COVER z BOTTOM CASE. z When you look into the inside of case, you can find , assembled HDD BRACKET. z Unlock those volts of ‘B’ part . (BRACKET separation) 4 & 8 & 16 Channel DVR Operation manual Revision 1.
z Assemble HDD with referring to below drawing . This is a picture of ref drawing for assembling each one of two HDD . z Those Volts used here are M3.5 x 5L HDD assembly volts (All are included IN Package when you purchase units or HDD ) 4 & 8 & 16 Channel DVR Operation manual Revision 1.
z You should do HDD JUMPER setting before or after HDD & BRACKET. This setting methods are different according to HDD manufacturer. z Generally you can find some setting information on the top of HDD, you can follows those instructions. z In case of one HDD installation, set HDD to ‘MASTER’ or ‘SINGLE’ . z In case of two HDD, one HDD set to ‘MASTER’, the other HDD set to ‘SLAVE’. z If you finish the installation of HDD& BRACKET, Put those finished HDD into DVR.
z A drawing of installation of HDD set in DVR. Pay attention to direction. z It can be connected to connector & HDD set of circled DVR main board. z This is a drawing to show how to connect HDD set and DVR main board. z You can find a red line which is a basic line and it should be matched with triangle shape of DVR main board. 4 & 8 & 16 Channel DVR Operation manual Revision 1.
5.2 Terminal Information 5.2.1 DSUB-9P (RS-232) 1 5 6 9 No Name Description 2 RXD Receive Data 3 TXD Transmit Data 5 GND Signal Ground 5.2.
#2 No Name 1 Description No Name Sensor5 9 Sensor13 2 Sensor6 10 Sensor14 3 Sensor7 11 Sensor15 4 Sensor8 12 Sensor16 5 Sensor9 13 GND Signal Ground 6 Sensor10 14 GND Signal Ground 7 Sensor11 15 GND Signal Ground 8 Sensor12 NO/NC Description NO/NC 4ch DVR: 4 sensors( 15pin D-sub is only one of back part) 8ch DVR: 8sensors, 16ch DVR: 16sensors * Abbreviation RSI RI RONOFFI ARO Record Start In Alarm Reset In Record On Off In Alarm Record Out 4 & 8 & 16 Channel
5.3 Factory Default Value 5.3.1 Main Menu Main Menu Sub Menu1 Menu Sub Menu 2 Default Vale Sub Menu 3 Camera Channel Setup Camera Name Channel No CH-1~CH-16 Covert OFF Picture Setting PTZ setup Remarks CH-1~CH-16 Contrast 9 Level Brightness 9 Level Hue 9 Level Model No NONE Max.
Detection Zone Sensor Setting Alarm In/Output ALL Sensor No Sensor 1 Sensor Type N.O. N.O. / N.C. Channel Link NONE CH1~CH16 Sensor Sensor 1 Alarm Output Motion OFF CH 1 Alarm Output Relay time OFF 0 sec 0, 5, 10, 15, 20, 25, 30, 35, 40, 45, 50, 55, 60 Post-Alarm Record 10 sec 10, 20, 20, 40, 50, 60 sec FTP Setting FTP Server 0.0.0.
Network Type STATIC Setup System DVR name Setup System password OFF Port 80 IP Address 192.168.1.200 Subnet Mask 255.255.255.0 Gateway 192.168.1.1 DNS IP 0.0.0.0 DHCP Port 80 PPPoE Port 80 ID dvr Registered ID Password 111111 Registered PW DNS IP 0.0.0.
System Video type Current Type NTSC, PAL info H/W version 0.9.1 Can be changed to S/W version 1.1-2418 Improve Kernel version 2.4.17_2 function Mac Address 00:09:F8:XX:XX:XX Audio Support the Depends on software version Language English French Depends German Japanese software Korean version Spanish 5.3.
5.4 Protocol 5.4.
50 51 52 53 54 55 56 57 58 59 ks1 ks2 ks3 ks4 ks5 ks6 ks7 kjleft kjright kpower Shuttle left 1Step Shuttle left 2Step Shuttle left 3Step Shuttle left 4Step Shuttle left 5Step Shuttle left 6Step Shuttle left 7Step Jog left Jog right Power 5.4.2 Usage - System protocol to control DVR from remote client software installed in PC or remote controller. - It maps button function of remote controller with front key in the front panel of DVR.
5.5 TV System Recording mode, Quality, FPS, HDD time table Resolution Quality Super Fine N Fine T 360*240 S Enhanced C Normal Recording time by HDD ( 1ch basis) Frame Rate 200GB 300GB 500GB 30 FPS 296.60 444.90 741.49 15 FPS 576.09 864.14 1440.23 8 FPS 809.49 1214.23 2023.72 6 FPS 991.77 1487.65 2479.42 4 FPS 1334.20 2001.30 3335.50 2 FPS 2122.28 3183.42 5305.70 1 FPS 3592.98 5389.47 8982.46 30 FPS 588.14 877.71 1462.86 15 FPS 1058.40 1587.60 2645.
TV System Resolution Quality Super Fine N Fine T 720*240 S Enhanced C Normal Recording time by HDD ( 1ch basis) Frame Rate 200GB 300GB 500GB 30 FPS 250.37 375.55 625.92 15 FPS 470.80 706.21 1177.01 8 FPS 651.19 976.79 1627.98 4 FPS 1047.57 1571.36 2618.93 3 FPS 1374.50 2061.74 3436.24 2 FPS 1612.60 2418.90 4031.50 1 FPS 2608.92 3913.38 6522.29 30 FPS 311.72 467.58 779.30 15 FPS 580.99 871.49 1452.48 8 FPS 787.69 1181.54 1969.23 4 FPS 1272.05 1908.
TV System Resolution Quality Super Fine P A L Fine 360*288 Enhanced Normal Recording time by HDD ( 1ch basis) Frame Rate 200GB 300GB 500GB 25 FPS 307.28 460.92 768.19 12 FPS 552.02 828.03 1380.05 8 FPS 706.21 1059.31 1765.52 6 FPS 910.22 1365.33 2275.56 4 FPS 1194.17 1791.25 2985.42 2 FPS 1828.57 2742.86 4571.43 1 FPS 3034.07 4551.11 7585.19 25 FPS 587.66 881.49 1469.15 12 FPS 1029.15 1543.72 2572.86 8 FPS 1244.98 1867.48 3112.46 6 FPS 1593.
TV System Resolution Quality Super Fine P A L Fine 720*288 Enhanced Normal z Recording time by HDD ( 1ch basis) Frame Rate 200GB 300GB 500GB 25 FPS 264.94 397.41 662.35 12 FPS 465.98 698.98 1164.96 7 FPS 650.16 975.24 1625.40 4 FPS 957.01 1435.51 2392.52 3 FPS 1230.03 1845.05 3075.08 2 FPS 1407.56 2111.34 3518.90 1 FPS 2275.56 3413.33 5688.89 25 FPS 327.68 491.52 819.20 12 FPS 573.67 860.50 1434.17 7 FPS 7898.21 1183.82 1973.03 4 FPS 1157.