Instruction manual

6
GB
Active Speaker System
Please read these operating instructions care-
fully prior to operation and keep them for later
reference.
1 Applications
This bass-reflex speaker system with integrated
power amplifier is suited for DJ applications and
other PA applications. It is equipped with:
— an MP3 player
— an FM radio
— a Bluetooth receiver to link mobile players
— an input for audio units
— a microphone input (PAK-8DMP and PAK-
10DMP only: this input can be switched to
line level for a second audio unit)
— an IR remote control
2 Safety Notes
The unit corresponds to all relevant directives of
the EU and is therefore marked with .
G
The unit is suitable for indoor use only. Protect
it against dripping water and splash water,
high air humidity and heat (admissible ambient
temperature range: 0 – 40 °C).
G
Do not place any vessel filled with liquid on the
unit, e. g. a drinking glass.
G
The heat produced inside the speaker system
must be dissipated by the cooling fins (models
PAK-10DMP, PAK-12DMP and PAK-15DMP);
therefore, never cover the cooling fins. Never
place the speaker system directly on a wall;
always keep a corresponding distance.
G
Immediately disconnect the mains plug from
the socket
1. if the unit or the mains cable is visibly dam-
aged,
2. if a defect might have occurred after the unit
was dropped or suffered a similar accident,
3. if malfunctions occur.
In any case the units must be repaired by
skilled personnel.
G
Never pull the mains cable to disconnect the
mains plug from the socket, always seize the
plug.
G
For cleaning only use a dry, soft cloth; never
use water or chemicals.
G
No guarantee claims for the unit and no liabil-
ity for any resulting personal damage or mate-
rial damage will be accepted if the unit is used
for other purposes than originally intended, if it
is not correctly connected or operated, or if it is
not repaired in an expert way.
3 Setting into Operation
3.1 Setting up the speaker system
Place the speaker system on a solid surface and
align it towards the audience. Place the tweeters
at ear level, if possible. Models PAK-12DMP and
PAK-15DMP are equipped with additional feet at
the lateral handles and can also be operated
horizontally as stage monitors; in this position,
sound will be radiated diagonally upwards.
Alternatively, place the speaker system via
the stand sleeve on its lower side on a standard
speaker stand with a tube diameter of 35 mm
(e. g. from the PAST series of “img Stage Line”).
For additional mounting options, e. g. suspen-
sion, the upper and lower sides of the cabinet
are provided with M8 threaded jacks. To use
these jacks, remove the cover caps.
For units with cooling fins on the rear: Set up
the speaker systems in such a way that air will
be able to flow freely through the cooling fins;
otherwise, there may be overheating and the
protective circuit will mute the sound.
3.2 Connecting the speaker system
Before making or changing any connections,
switch off the speaker system and the units to be
connected.
1) To connect a microphone, use the XLR jack
or 6.3 mm jack MIC (/ LINE) INPUT.
Models PAK-8DMP/-10DMP: Engage the
button LINE / MIC next to the 6.3 mm jack to
increase the input amplification for micro-
phone signals.
2) To connect an audio unit with line output
(e. g. mixer, CD player, microphone pream-
plifier, active speaker system), use one of the
jacks LINE INPUT:
3.5 mm jack
RCA jacks
XLR jack (only for PAK-12DMP/-15DMP)
3) Models PAK-8DMP/-10DMP: The 6.3 mm jack
or XLR jack MIC / LINE INPUT can be used to
connect a second audio unit instead of a
microphone. Disengage the button LINE/ MIC
next to the 6.3 mm jack to match the input
amplification for line signals.
4) If an additional active speaker system is
required for PA applications of larger zones,
connect the line input of this speaker system
to the XLR output MIX OUT. Alternatively,
connect a recorder to this jack.
5) For power supply, use the mains cable pro-
vided to connect the mains jack on the rear to
a mains socket (230 V~ / 50 Hz).
3.3 Infrared remote control
The remote control (fig. 5) for the MP3 player/
radio / Bluetooth module (fig. 1) is supplied with a
battery. Before the first operation, remove the
protective film from the battery holder. When you
press a button on the remote control, always
point the remote control at the front of the
speaker system. Make sure that there are no
obstacles between the speaker system and the
remote control.
If the remote control is not in use for a longer
period of time, always remove the battery to pre-
vent damage due to battery leakage.
If the unit is to be put out of operation
definitively, take it to a local recycling
plant for a disposal which is not harmful
to the environment.
WARNING The unit uses dangerous mains
voltage. Leave servicing to skilled
personnel only. Inexpert handling
may result in electric shock.
87 9
54 6
21 3
100+
0
200+
+
EQ
MUTE
MODESTOP
NEXT PLAY/PAUSE PREV
VOLÐ VOL+

MP3 player / radio / Bluetooth module

PAK-8DMP/ PAK-10DMP Connections, controls

PAK-12DMP Connections, controls

PAK-15DMP Connections, controls

Remote control