Ver 1.0 Robot Cleaner .& 4UZMF 6TFS .BOVBM ME770 4UZMF .3 7. Thank you for purchasing the ME770 4UZMF robot cleaner. Before using the product, please read this User Manual carefully, and keep it for future reference. Depending on your model, some contents of this User Manual may differ from the actual product. The contents of this User Manual are subject to change without notice. Downloaded from www.Manualslib.
Overview Robot Cleaner ǘTopǘ 3 1 2 4 5 ǘRearǘ 7 8 9 1 Control buttons and indicators 2 $BNFSB 3 %VTU #JO $PWFS 4 Bumper 6 5 10 11 Obstacle and signal detection sensors 6 Air outlet 7 Adaptor jack ǘBottomǘ 14 13 10 8 Power switch 12 13 9 Signal receiving sensor 10 10 Cliff detection sensors 11 Charging terminals 12 12 15 16 12 Wheels 13 Side brush installation pins 14 Dust inlet 15 Main brush 1 Mop plate installation holes 11 Downloaded from www.
Robot Cleaner Control Buttons and Indicators 1 Start/stop button 2 Power button 11 10 3 Cleaning mode selection button 9 8 7 4 7BDVVN $MFBOJOH NPEF JOEJDBUPS 12 13 14 15 5 $IBSHJOH NPEF indicator 6 5 4 1 2 6 4IBEPX $MFBOJOH NPEF indicator 7 *OUFOTJWF $MFBOJOH mode indicator 8 )ZCSJE $MFBOJOH NPEF indicator 3 9 .
Before Use Remote Control You can conveniently access the various functions of the robot cleaner with your remote control. Functions that can be controlled through the control panel on the robot cleaner: WBDVVN DMFBOJOH IZCSJE DMFBOJOH mop cleaning, TIBEPX DMFBOJOH JOUFOTF DMFBOJOH and charging.
Installing the Charger 1 Connect the power adaptor. Þ Set the robot cleaner detection distance (5 m or 8 m). Þ Place the power adaptor in the holder of the charger. Þ 2 Þ 3 Þ Check the power connection (blue lamp). Check the location of the charger.
*OTUBMMJOH Charging If you have prepared the charger, main body, and remote control, you must then charge the battery of the robot cleaner to use it. To charge the robot cleaner, follow these steps: 1 Þ 2 Þ Turn the power switch on. Hold the robot cleaner with both hands and put it on the charger. Match the terminals of the robot cleaner with the terminals of the charger.
Robot Cleaner Installing the Water Supply Big Mop Kit 1 � 3 2 Supply water into the mop plate and attach the mop to it. Þ � Attach the mop plate. Fit the joint parts well to the holes of the robot cleaner. Þ Ě If you apply excessive force to the mop plate when you install it on the robot cleaner, the joint parts of the mop plate may be damaged. 4 Turn the power switch off (on the lower rear side of the robot cleaner). Þ � Flip it over and turn the system power switch on.
Robot Cleaner Product Operation Big Mop Recommendation .& 4UZMF’s specially designed Big Mop can be rewashed and reused. Þ Dampen the Big Mop before attaching it to the XBUFS Tank. Þ Make sure the Big Mop is not excessively wet to avoid the wheels from slipping. Þ You may add cleaning solution to the Big Mop, but it may create wheel slippage. Þ The .& 4UZMF with Big Mop is designed to clean hard surface floors including wood, tile, vinyl, linoleum and laminate. The .
Product Operation Before You Start Check the following before you start the robot cleaner. 1 Be careful not to break the robot cleaner when you pull the robot cleaner out of the box. For information of installing the robot cleaner, see page 14. 2 Check the location (L/R) of the brushes and install them. For information on installing the brushes, see page 15. 3 Pull the robot cleaner out and manually charge it first.
Robot Cleaner Starting & Stopping Cleaning Starting Cleaning 1 Turn the power switch on. Þ 2 3 or 4 or If you are cleaning an area that is difficult to clean using auto cleaning mode, change to the proper cleaning mode. Þ Stopping Cleaning After cleaning, the robot cleaner returns to the charger or stops on the spot according to the cleaning mode. � If you press the Start/stop (ⶺ Ħ ) button when the robot cleaner is operating, the cleaning will be stopped. or 2 Downloaded from www.
Product Operation Changing the Cleaning Mode User can set the cleaning mode to match the cleaning environment.
Product Operation Hybrid Cleaning In Hybrid Cleaning, the robot cleaner performs the Vacuum Cleaning and Mop Cleaning at the same time. Hybrid Cleaning offers a comprehensive floor care solution because of the use of the twin side brushes, the main brush, the BLDC suction, and the reusable microfiber Big Mop with the Water Supply Tank all together. The Hybrid Cleaning is recommended for comprehensive cleaning on your hard floors.
Product Operation Robot Cleaner Vacuum Cleaning Vacuum cleaning is used where the needs are vacuum suction only without mop cleaning. It can be used on hard floor or carpet. 1 3 2 Turn the system power switch on. Þ Select the Vacuum Cleaning with the Mode button on the Control Panel and press the Start/Stop button or just press the Vacuum Cleaning button on the remote control. Þ � Turn the main power button on.
Product Operation Mop Cleaning Mop Cleaning mode is used for when you need mopping only without vacuuming. Ě If Mop Cleaning mode is used on carpet or rug, the carpet or rug can be damaged. Therefore, please use the Mop Cleaning mode only on hard floor. Ě For Big Mop with Water Supply Tank, we recommend moistening the Big Mop before attaching it for longer wet cleaning performance. 1 Follow the directions on page 1 to attach the Big Mop with the Water Supply Tank.
Product Operation Intensive Cleaning The robot cleaner intensively cleans the surrounding area relative to its current location. 1 2 Turn the power switch on. Þ or 3 � or 4 Ě In Auto Cleaning mode, the robot cleaner stops on the spot after it has finished the cleaning. Ě In the area in which there are many obstacles, the robot cleaner may not operate in normal cleaning modes. 2 Downloaded from www.Manualslib.
Product Operation Robot Cleaner Shadow Cleaning You can clean under your bed or furniture. Ě To use shadow cleaning mode, turn the room light on. In a dark room, the robot cleaner can’t detect the space under the bed or furniture. Ě The robot cleaner moves to a place under the bed or furniture to start shadow cleaning. To reduce the time spent moving through the room, put the robot cleaner in front of the bed or furniture under which you want to perform shadow cleaning.
Product Operation Manual Cleaning You can control the robot cleaner directly using the remote control. 1 Stop the robot cleaner that is operating by pressing the Start/stop (Ě Ħ) button. Þ or 2 Press the Manual button on the remote control. Þ Air suction will start in its current place. If you press the Manual button again, air suction will be stopped. 3 By pressing direction keys on the remote control, you can move the robot cleaner where you want it to go.
Robot Cleaner Scheduled Cleaning (Reservation Cleaning) For daily efficient hands free cleaning, the robot cleaner provides 2 Reservation Cleaning modes. One starts cleaning after 1 hour from the time you set it and the other starts at the same time everyday. Ě Reservation Cleaning only works from the charging station after you set the Reservation Cleaning. You must put the robot cleaner on the charging station to begin at the scheduled time.
Product Operation Turbo Option While you are using the Hybrid / Vacuum / Intensive / Shadow / Manual Cleaning, by pressing the Turbo button on the remote controller you can control suction power. Ě Turbo option is not available in Hybrid Cleaning mode and Mop Cleaning mode. or � Power off Power on Threshold Option For less than a 1cm threshold height of threshold or carpet, rug and etc, the user is able to choose threshold climbing over ON/OFF option by the remote control.
Robot Cleaner Double Deep Cleaning Option The Double Deep Cleaning Option performs 2 cleaning sessions of the vertical pattern overlapped by the horizontal pattern. Deep Cleaning Pattern Vertical pattern overlapped by the horizontal pattern Ě The 1 Double Deep Cleaning Option Performs 2 cleaning sessions of the vertical pattern overlapped by the horizontal pattern. factory default is set to Deep Cleaning Pattern in Hybrid / Vacuum / Mop / Shadow Cleaning modes. Turn the system power switch on.
Product Operation 3 Select any one of Hybrid / Vacuum / Mop / Shadow Cleaning. To learn how to select these options, you may refer to the relevant sections on the User Manual. Þ or 4 or Press the Double CL button on the remote control. The Double Deep Cleaning Option indicator is now turned on. Þ or 5 The robot cleaner will perform 2 cleaning sessions of the vertical pattern overlapped by the horizontal pattern.
Downloaded from www.Manualslib.
Product Operation .BJOUFOBODF Cleaning Sensors and Wheels Cleaning Sensors Clean (blow or wipe) the three sensors with the included cleaning brush or a cotton swab. Þ If sensors are severely contaminated, wipe with a moistened cotton swab. Do not wipe directly with water, and do not use benzene or alcohol to clean sensors. Cleaning Wheels Clean wheels using the brush. Þ To clean the front wheel, remove the screws and remove the wheel, and clean it with the brush.
Robot Cleaner Cleaning the Dust Inlet 2 1 � Remove the dust inlet cover. 3 Remove the main brush. 4 Clean the removed main brush with the cleaning brush. 5 � To reinstall the dust inlet cover, insert the 2 tips to the matching holes on the robot cleaner. Downloaded from www.Manualslib.com manuals search engine Check the groove’s shape and insert the main brush into the fixing hole, and then secure the wing of the fixing pin to the fixing pin.
.BJOUFOBODF Using and Managing the Battery The battery is a consumable item. The more you use the battery, the shorter the battery’s lifetime. Battery Lifetime We guarantee 6 months of use in a normal environment. Þ Always charge the battery for the best use experience. Þ The battery lifetime may vary depending on the use environment. Þ Charging Battery If you are using the robot cleaner for the first time, please fully charge the battery first.
Robot Cleaner Battery Replacement If you notice that the operating time has been significantly reduced, you may need to replace the battery. Þ You must use a battery that is manufactured by Moneual. Þ Remove the battery from the robot cleaner when the system power is off. Þ Dispose of your old batteries according to the local laws and regulations of your region. To purchase an extra battery, please contact our customer service.
.BJOUFOBODF Maintenance 4 Install the new battery and connect the battery cable connector. Replace the battery cover and tighten with four screws. � Battery Handling and Safety Information I f you leave the fully discharged battery for a long time, the battery may become damaged and you may not be able to use it. Þ I f you use a battery other than Moneual’s for use with the robot cleaner or the battery may be damaged. Þ R emove the battery before disposing of the robot cleaner.