Design Guide with Installation Instructions Fresh-Food Refrigerator ZIFI240 ZIFS240 Bar Refrigerator with Icemaker ZIBI240 ZIBS240 monogram.
Safety Information BEFORE YOU BEGIN If you received a damaged refrigerator, you should immediately contact your dealer or builder. Skill Level – Installation of this refrigerator requires basic mechanical, carpentry and plumbing skills. Proper installation is the responsibility of the installer. Product failure due to improper installation is not covered under the GE Appliance Warranty. See the Owner’s Manual for warranty information. Read these instructions completely and carefully.
Consignes de Sécurité Ce symbole représente une alerte de sécurité. Ce symbole vous avise de dangers possibles pouvant causer la mort, des blessures ou autres. Tous les messages de sécurité seront précédés du symbole d’alerte de sécurité ainsi que des mots « DANGER », « AVERTISSEMENT » ou « MISE EN GARDE ». Ces messages sont les suivants : DANGER Signale une situation qui présente un danger imminent et qui, si elle n’est pas évitée, entraînera des bles sures graves, voire la mort.
Installation Instructions CARING FOR YOUR STAINLESS STEEL CONTENTS Important Information ...................................................................................2, 3 Parts Required ............................................................................................................4 Caring for Your Stainless Steel ..........................................................................4 Tools, Hardware ....................................................................................
Design Guide For models ZIFS240 and ZIBS240 with Stainless Steel Doors and Handles THE INSTALLATION SPACE THE INSTALLATION SPACE (cont.) Flush Installation NOTE: Water line location for ZIBS240 model only CABINET 1/4” Filler panel or cleat to be set back even with front of case. CABINET Front edge of product case Front face 110° These products will fit flush to adjacent cabinets when installed with a 1/4” filler panel or cleat.
Design Guide For models ZIFS240 and ZIBS240 with Stainless Steel Doors and Handles SIDE-BY-SIDE INSTALLATIONS PRODUCT CLEARANCES For a complete refreshment center, install a FreshFood Refrigerator beside a Double-Drawer Refrigerator, Beverage Center or Wine Chiller/Wine Reserve. Or, install a Refrigerator with Icemaker beside a Wine Chiller/Wine Reserve.
Design Guide For models ZIFI240 and ZIBI240 with Custom Door Panels and Handles THE INSTALLATION SPACE SIDE-BY-SIDE INSTALLATIONS For a complete refreshment center, install a FreshFood Refrigerator beside a Double-Drawer Refrigerator, Beverage Center or Wine Chiller/Wine Reserve. Or, install a Refrigerator with Icemaker beside a Wine Chiller/Wine Reserve. • A side-by-side installation requires at least a 47-1/2”wide opening. No trim kits required.
Installation Instructions STEP 1 REMOVE PACKAGING AND INSTALLATION PARTS STEP 2 REVERSING THE DOOR • Remove corner blocks and foam drawer stops. • Remove all packing material, tape and protective plastic coverings. • Remove the toekick attached to the back of the unit. • Remove the custom panel attached to the front of the unit. • Remove the top hinge pin (do NOT discard). (ZIFI240 model only) • Flip the door 180 degrees.
Installation Instructions STEP 2 REVERSING THE DOOR STEP 2 REVERSING THE DOOR (ZIFI240 model only) (Cont.) (ZIFS240 model only) • Install the new left bottom hinge pin and new door stop that are enclosed in the hardware bag. • Remove top hinge and discard. Hold the door in place. • Remove the black screw-hole cover from top left of cabinet and insert in top right. • Install the bottom trim onto the new bottom side of the door. • Remove 2 screws tor remove the toekick (do not discard).
Installation Instructions STEP 2 REVERSING THE DOOR (ZIFS240 model only) (Cont.) STEP 2 REVERSING THE DOOR (ZIFS240 model only) (Cont.) • Remove top plug/bushing from the door using a flat head screwdriver. Discard the bushing. • Re-insert the black screw post in the new bottom of the door. • Rotate the door 180°. • Remove the screw from the plug/bushing on the bottom of the door. Discard the plug/bushing but keep the screw. • Insert the new bottom plug/bushing in the new bottom of the door.
Installation Instructions STEP 3 INSTALL CUSTOM 3/4” DOOR PANEL AND HANDLE STEP 3 INSTALL CUSTOM 3/4” DOOR PANEL AND HANDLE (ZIFI240 and ZIBI240 models only) (ZIFI240 and ZIBI240 models only) 3/4” Overlay Panel Dimensions Model ZIFI240 and ZIBI240 require a field-installed overlay door panel. Overlay • The overlay panel must be Panel secured to a 1/4” thick backer Door panel that slides into the trim. A .10” thick spacer panel must be placed between the overlay and backer panel.
Installation Instructions STEP 4 LEVEL STEP 3 INSTALL CUSTOM 3/4” DOOR PANEL AND HANDLE (CONT.) • Use an adjustable wrench to turn the leveling legs and raise or lower the product. For built-in installation, adjust the leveling legs slightly below the bottom of the countertop. INSTALLATION TIP: Measure floor to underside of countertop inside the opening.
Installation Instructions STEP 6 CONNECT POWER STEP 8 SET TEMPERATURE CONTROLS • Connect power cord plug to a properly grounded receptacle. • Check to make sure power is on by opening the door to see if interior light turns on. • Bar Refrigerator with Icemaker – The interior fan runs all the time except during defrost cycle when the door is open. • Fresh-Food Refrigerator – The interior fan runs all the time except when the door is open. See the Owner’s Manual for further explanation of the fan.
Notes 14
Notes 15
NOTE: While performing installations described in this book, safety glasses or goggles should be worn. For Monogram® local service in your area, call 1.800.444.1845. NOTE: Product improvement is a continuing endeavor at General Electric. Therefore, materials, appearance and specifications are subject to change without notice. Pub. No. 31-51544-8 Part No. 197D5893P002 01-15 GE Printed in Slovenia GE Appliances Appliance Park Louisville, KY 40225 GEAppliances.