Installation Sheet

ManualsBrandsMonogram Brass ManualsShop AllMonogram Brass Adjustable Shower Drain with Square Brass Strainer

Installation Instructions | SHOWER DRAINS

This carded product comes complete with trilingual installation, operating, care and maintenance instructions. Dimensions are subject to manufacturer’s tolerance and can change without notice.

Distributed by Ferguson and Wolseley Canada.

Installation:

Note: MONOGRAM BRASS shower drain instructions assume the shower framing has been constructed and the flooring is plywood .

Generally the same principle applies to concrete flooring where the sloped mortar bed is applied beneath the pan liner. Also the instructions

apply to either PVC pan liner or CPE pan liner which are installed the same with the exception of the bonding adhesive used for seaming

and dam corner applications.

Step 1: Staple building paper to the subfloor of the

shower base. Disassemble the shower drain, set the

screws, plate, ring and body aside. Also remove the

screws from the collar to separate the collar from flange.

Square Top Tile-In Shower Drain

Screw

Brass Grate

Brass Grate Plate

Adjustable Drain Barrel

Reversible

Clamping Collar

Screw

Drain Base

Step 2: Glue the bottom piece to the drain pipe with

appropriate cement. Partially screw the drain bolts into

the drain piece and place a rag in the drain pipe to

prevent mortar from falling into the drain.

Step 3: Staple galvanized lath over the building paper,

according to instruction of galvanized lath layer.

Step 4: Apply mortar layer, trowel mortar over the

galvanized lath from the outside of flange adapter up to

the marked height of perimeter of shower base. Verify

the slope of the mortar is even and fill in any low spots

with mortar. Allow the mortar to cure overnight,

according to instruction of mortar.

Step 5: Place the waterproof membrane or shower pan

liner on top of mortar. Prepare waterproof membrane or

shower pan liner according to instruction of shower pan

liner's application instructions. Cut away the shower pan

liner at the screw location on the flange adapter and

at the drain outlet.

Step 6: Assemble drain, to position the middle drain

collar piece over the bolt holes. Install the bolts,

tightening them evenly and firmly to create a watertight

seal. Insert an inset into the drain, and then fill the shower

base with water. Allow the water to sit overnight to check

for leaks.

Step 7: Assemble body and strainer of drain,

Set the ring on the strainer body. Set the plate inside the

ring, and then secure the plate with two screws (provided).

Step 8: Apply tile layer, then install the tile to finish.

CAP 05/17-C

Summary of content (3 pages)

PAGE 1
Installation Instructions | SHOWER DRAINS Note: MONOGRAM BRASS shower drain instructions assume the shower framing has been constructed and the flooring is plywood . Generally the same principle applies to concrete flooring where the sloped mortar bed is applied beneath the pan liner. Also the instructions apply to either PVC pan liner or CPE pan liner which are installed the same with the exception of the bonding adhesive used for seaming and dam corner applications.
PAGE 2
Instructions d'installation | DRAINS DE DOUCHE Remarque : Les instructions de drain de la douche MONOGRAM BRASS supposent que la structure de la douche a été construite et que le sol est en contreplaqué. En général, le même principe s'applique à un sol en béton avec une chape en ciment inclinée appliquée au-dessous d'une membrane d'étanchéité.
PAGE 3
Instrucciones de instalación | DESAGÜE PARA REGADERA Nota: En las instrucciones para el desagüe de regadera MONOGRAM BRASS se asume que ya se construyó la estructura y que el suelo es de madera laminada. Generalmente se aplica el mismo principio para el suelo de concreto, en el que se aplica una capa de mortero en declive entre el recubrimiento del casetón.