INSTALLATION INSTRUCTIONS Advantium® Built-In Wall Oven 240V 30” ENGLISH/ESPAÑOL MONOGRAM.
Safety Information BEFORE YOU BEGIN Read these instructions completely and carefully. IMPORTANT — Save these instructions for local inspector’s use. IMPORTANT — Observe all governing codes and ordinances. • Note to Installer — Be sure to leave these instructions with the Consumer. • Note to Consumer — Keep these instructions with your Owner’s Manual for future reference. • Skill Level — Installation of this appliance requires basic mechanical and electrical skills. • Completion Time — 1 Hour.
Design Information PRODUCT DIMENSIONS AND CLEARANCES 21-1/2Ǝ 2-1/4Ǝ NOTE: Appearance will vary by model.
Installation Preparation ELECTRICAL REQUIREMENTS Single Advantium Installation Product rating is 120/208 or 120/240 volt, 60 Hz, 30 amps. This product must be connected to a supply circuit of the proper voltage and frequency and protected by a time delay fuse or circuit breaker. Power should be supplied from a separate, dedicated 30-ampere branch circuit. Wire size must conform to the requirements of the National Electrical Code or the prevailing local code.
Installation Preparation IMPORTANT: Always maintain 36-3/4” minimum height from the floor to the cutout in any single or combined installation. PREPARE THE OPENING PREPARE THE OPENING The Advantium 240V can be installed in combination with other Monogram Built-In appliances. Always follow each product’s Installation Instructions to complete the installation.
Installation Preparation IMPORTANT: Always maintain 36-3/4” minimum height from the floor to the cutout in any single or combined installation. PREPARE THE OPENING (CONT.) Installation over a Wall Oven: 30” 23-1/2” 25-1/4” 17-1/2” PREPARE THE OPENING (CONT.) Installation over a Wall Oven and Warming Drawer: Construct Solid Bottom Min. 3/8” Plywood Supported by 2x4 or 2x2 Runners all Four Sides 30” 23-1/2” 25-1/4” 2” Min. (3” recommended) 17-1/2” Per Oven Requirement 45-1/4” Min.
Flush Mount Installation Preparation PREPARE THE INTERIOR PREPARE THE OPENING Cut and install side cleats: • Cut side wood cleats to height of cabinet opening and approx. 2-1/2” in depth. Install, on each side, Dim. E (See table below) from the front face of the cabinet. Cut and install bottom cleat: • Cut bottom wood cleat to a height of 1-1/8”, a depth of the cabinet minus Dim. E (See table below) and a width of 25-1/4” to fit between side cleats.
Installation Preparation with Accessory Storage Drawer Preparation with an Accessory Storage Drawer As needed, see the Standard Mount Installation Preparation OR Flush Mount Installation Preparation for configuration details. Note the modified cutout height below. PREPARE THE OPENING (cont.) The Advantium Built-In Oven can be installed in combination with other Monogram appliances. Always follow each product’s Installation Instructions to complete the installation.
Installation Instructions 1 REMOVE THE PACKAGING AND PARTS • Remove all packing material and tape. • Locate parts package containing mounting screws. • Remove the oven from the carton. Do not lift unit by handle or conduit. Two people are required to lift this oven. • Open the door and remove any packaging in oven.
Installation Instructions 2 ROUTE CONDUIT THROUGH CUTOUT CAUTION Two people are required to lift the oven into the opening. Grasp the bottom at front and rear. Discard foam base. DO NOT USE HANDLE OR CONDUIT TO LIFT THE OVEN. DAMAGE WILL OCCUR. With oven in front of the cabinet opening: • Insert conduit into cabinet opening. Connect oven wiring and branch circuit. • Lift the oven into the opening while continuing to feed the conduit in the direction of the installed junction box.
Installation Instructions 3 INSTALL BOTTOM TRIM 4 INSTALL MOUNTING SCREWS NOTE: If installing the Advantium 240 Oven with an accessory storage drawer, the bottom trim is not required. Proceed to Step 4. • Align bottom trim tabs to slots in the bottom of the oven. • Secure the bottom trim to the bottom of the oven using 3 brass screws provided. • Slide the oven the remaining way into the opening so that the side flanges and control panel are against the cabinet frame.
Notes 12 31-7000080 Rev.
Notes 31-7000080 Rev.
31-7000080 Rev.0 08-19 GEA Printed in China 14 31-7000080 Rev.
INSTRUCCIONES DE INSTALACIÓN Horno Advantium® 240V 30” ESPAÑOL MONOGRAM.
Información sobre Seguridad ANTES DE COMENZAR Lea estas instrucciones en su totalidad y atentamente. IMPORTANTE — Conserve estas instrucciones para uso del inspector local. IMPORTANTE — Cumpla con todos los códigos y ordenanzas gubernamentales. • Nota para el Instalador — Asegúrese de que el Comprador conserve estas instrucciones. • Nota para el Consumidor — Guarde estas instrucciones con su Manual del Propietario para referencia futura.
Información de Diseños DIMENSIONES Y ESPACIOS DE DESPEJE DEL PRODUCTO NOTA: La apariencia variará según el modelo 21-1/2Ǝ 2-1/4Ǝ Profundidad de la puerta Vea la tabla de abajo 29-3/4” 20-1/4” 1Ǝ 13 1/4Ǝ HERRAMIENTAS Y PIEZAS REQUERIDAS (NO SUMINISTRADAS) • Modelo Door Depth ZSB9231NSS 1-3/8” ZSB9232NSS 1-7/16” Destornillador Phillips nº 2 • Perforadora manual PLANIFICACIÓN ANTICIPADA • 7DODGUR GH DOWD YHORFLGDG GLiPHWUR GH Ǝ • 'HVWRUQLOODGRU FRQ SXQWD 3KLOOLSV GH Ǝ • Nivel •
Preparación de la Instalación REQUISITOS ELÉCTRICOS Instalación única de advantium La calificación del producto es 120/208 o 120/240 voltios, 60 hz, 30 Amperios. Este producto debe estar conectado a un circuito de alimentación con el voltaje y la frecuencia adecuados y estar protegido por un fusible de retardo de tiempo o un disyuntor. La energía se debe suministrar desde un circuito derivado separado de 30 amperios.
Preparación de la Instalación IMPORTANTE: Mantenga siempre una altura mínima de 36-3 / 4 ”desde el piso hasta el recorte en cualquier instalación individual o combinada. PREPARACIÓN DE LA ABERTURA PREPARACIÓN DE LA ABERTURA (CONT.) El Advantium 240V se puede instalar en combinación con otros dispositivos integrados de Monogram. Siga siempre las instrucciones de instalación de cada producto para completar la instalación.
Installation Preparation IMPORTANTE: Mantenga siempre una altura mínima de 36-3 / 4 ”desde el piso hasta el recorte en cualquier instalación individual o combinada. PREPARACIÓN DE LA ABERTURA (CONT.) Instalación sobre un horno de pared: * Si reemplazará un horno eléctrico Construya un 30” 23-1/2” 25-1/4” 17-1/2” PREPARACIÓN DE LA ABERTURA (CONT.) Instalación sobre un horno de pared y un cajón calentador: fondo sólido, sostenido por un contrachapado de un mínimo de 3/8” sobre los cuatro lados.
Preparación de la Instalación para el Montaje al Ras (Monogram Únicamente) PREPARE EL INTERIOR Corte e instale los ristreles laterales: • Corte los ristreles de madera laterales a la altura de la abertura del gabinete y a aproximadamente 2 1/2” de profundidad. Instale, a cada lado, a Dim. E desde la cara frontal del gabinete. Corte e instale el ristrel inferior: • Corte el ristrel de madera a una altura de 1 1/8”, una profundidad del gabinete menos Dim.
Preparación de la Instalación Preparación con un cajón de almacenamiento de accesorios Según sea necesario, consulte la Preparación para la instalación del montaje estándar O la Preparación para la instalación del montaje empotrado para obtener detalles de configuración. Tenga en cuenta la altura de corte modificada a continuación PREPARACIÓN DE LA ABERTURA (cont.) El Advantium puede ser instalado junto con otros electrodomésticos.
Instrucciones de Instalación 1 RETIRE EL EMBALAJE Y LAS PIEZAS • Retire todo el material de embalaje y la cinta. • Ubique el paquete de piezas que contiene los tornillos de montaje. • Retire el horno del cartón. No levante la unidad de la manija ni del conducto. Es necesario que el horno sea levantado por dos personas. • Abra la puerta y retire cualquier embalaje que haya dentro del horno.
Instrucciones de Instalación 2 CONDUCTO DE LA RUTA A TRAVÉS DEL RECORTE PRECAUCIÓN Se requieren dos personas para 2 CONDUCTO DE LA RUTA A TRAVÉS DEL RECORTE (CONT.) levantar el horno en la abertura. Sujete la parte inferior en la parte delantera y trasera. Deseche la base de espuma. No use la manija ni el conducto para levantar el horno.
Instrucciones de Instalación 3 INSTALE LA MOLDURA INFERIOR 4 INSTALACIÓN DE LOS TORNILLOS DE MONTAJE NOTA: Si instala el horno Advantium 240 con un cajón de almacenamiento de accesorios, no se requiere el adorno inferior. Continúe con el paso 4. • Alinee las lengüetas del borde inferior con las ranuras en la parte inferior del horno.
Notas 12 31-7000080 Rev.
Notas 31-7000080 Rev.
31-7000080 Rev.0 08-19 GEA Printed in China 14 31-7000080 Rev.