Appliances Installation Instructions If gou have questions, call 800.626.2000 or visit our website at: www.monogram.
Safetg Information BEFORE YOU BEGIN Read these instructions completelg and curefullg. IM PORTANT Observeallgoverningcodes and I L J I'_ t'_ I"1"1" A k I'It" I m i"%Ji_ I _1_1|The dishwasherMUST be installed toallowforfutureremovalfromtheenclosure if service is required. If gou received a damaged dishwasher, gou should immediatelg contact gour dealer or builder. ordinances. Note to Installer - Be sure to leave these instructions for the consumer's and local inspector's use.
installation Preparation PARTS SUPPLIED: [] Two #8 Phillips head wood screws, 5/8" long to secure dishwasher to underside of countertop (in literature package).
installation Preparation PREPARE DISHWASHER • The dishwasher must be installed so that drain hose is no ENCLOSURE more than 10' in length for proper drainage. I G To reduce the risk of electric shock, fire, or injury to persons, the installer must ensure that the dishwasher is completelg enclosed at the time of installation. 34-1/2"+ 1/2" Underside of Countertop to Floor CLEARANCES: When Square and Plumb 18" Max.
installation Preparation PREPARE ELECTRICAL WIRING FORPERSONALSAFETY: Remove house fuse or open circuit breaker before beginning installation. Do not use an extension cord or adapter plug with this appliance. Electrical Requirements • This appliance must be supplied with 120V, 60Hz., and connected to an individual properly grounded branch circuit protected by a 15 or 20 ampere circuit breaker or time delay fuse. • Wiring must be 2 wire with ground and rated for 75°C(176°F).
Installation Instructions PREPARE HOT WATER LINE BEFORE YOU BEGIN The line may enter from either side, rear or floor within the shaded area shown in Figure F. The line may pass through the same hole as the electrical cable and drain hose. Or,cut an additional 1-1/2" dia. hole to accommodate the water line. If power cord with plug is used, water line must not puss through power cord hole. STEP 1 CHECK DOOR BALANCE CAUTION: The hot water supply line pressure must be at least 20 psi.
Installation Instructions Lay the dishwasher on its back. Remove the four screws securing the toekick to the dishwasher, and remove the toekick. Remove the side panels and set the dishwasher upright. To adjust the door springs: Pull the spring adjustment pin out of the holes, insert in the next highest or lowest hole and test again. Increase Decrease Figure K Remove the single screw just above and to the side of each front leveling leg. Figure J Adjust both door springs to the same tension.
Installation Instructions STEP 2 ADJUST LEVELING LEGS Hove the dishwasher close to the installation location and lag it on its back. O Adjustto Installation STEP 4 INSTALL POWER CORD Skip this step if dishwesher will be direct wired. Use Power Cord Kit WX09X70910, available for purchase from an authorized GEAppliance Dealer. The power cord and connections must complg with the National Electrical Code, Section 422 and/or local codes and ordinances. Maximum power cord length is 6'.
Installation Instructions STEP 6 POSITION WATER LINE AND HOUSE WIRING STEP 8 SLIDE DISHWASHER PARTIALLY INTO CABINET , Position water supply line and house wiring on the floor of the opening to avoid interference with base of dishwasher and components under dishwasher. DO NOT PUSH AGAINST FRONT PANELWITH KNEES. DAMAGE WILL OCCUR. , Slide dishwasher into the opening a few inches at a time. _Sides Re osition Dishwasher Water Wiring Line Figure P Front Door Panel With Knee.
installation instructions STEP 9 POSITION DISHWASHER UNDER COU NTERTOP • Push the dishwasher into the cabinet. • Push the sides with your hands. Do not use your knee against the door since door damage will occur. • Check that the tub insulation blanket does not get "bunched-up" or interfere with the springs as you slide it into the cabinet. • Center the dishwasher in the opening. • Front of door panel should be flush with face of cabinet.
Installation Instructions STEP 10 LEVEL DISHWASHER IN PORTANT- Dishwasher must be level for proper dish rack operation and wash performance. • Make sure 1/2" minimum gap is maintained (see Figure T). Place level on door to check that the dishwasher is level sideto-side. Place level on rack track inside tub to check that the dishwasher is level front-to-back. STEP 11 SECURE DISHWASHER TO COUNTERTOP OR CABINET In this step gou will need the 2 Phillips special head screws set aside prior to Step 1.
Installation Instructions STEP 12 CONNECT WATER SUPPLY DRAIN LINE INSTALLATION Connect water supplg line to 90 ° elbow. • Slide compression nut, then ferrule over end of CompressionNut water line. Ferrule Insert water line into 90 ° elbow. Slide ferrule against Hot Water z elbow and secure with _o Elbow SupplyLine compression nut. f--
Installation Instructions STEP 14 CONNECT POWER SUPPLY STEP 15 PRETEST CHECK LIST Skip this step if equipped with power cord. Verifg that power is turned offat the source. Remove junction box cover "A". Review this list after installing your dishwasher to avoid charges for a service call that is not covered by your warranty. Locate the three dishwasher wires, (white, black and green) with stripped ends. Insert dishwasher wires through the small hole in the junction box "B".
Installation Instructions STEP 16 DISHWASHER WET TEST STEP 17 REPLACE TOEKICK [] Turn on power supply (or plug power cord into outlet, if equipped). [] St(]rt the unit to check for le(]ks. - Press ON/OFF button to turn unit on - Press CYCLESELECTbutton until light below RINSEcycle illumin(]tes [] Close door. [] Check to be sure th(]t w(]ter enters the dishw(]sher. If w(]ter does not enter the dishw(]sher, check to be sure th(]t w(]ter (]nd power (ire turned on. [] Check for le(]ks under the dishw(]sher.
