Installation Instructions Automatic Icemaker ZDIC150 ZDIS150 Design Guide With Installation Instructions monogram.
Installation Instructions • BEFORE YOU BEGIN: CONTENTS Read these instructions completely and carefully. • Design Information Models Available ....................................................................3 Cutout & Product Dimensions..........................................3 Optional Accessories............................................................4 Tools and Materials Required ........................................ 4 IMPORTANT: Save these instructions for local inspector’s use.
Design Information MODELS AVAILABLE ZDIC150, ZDIS150 Available in black and stainless steel. The icemaker may be installed below a countertop or used free-standing. CUTOUT & PRODUCT DIMENSIONS Flush Installation, Top View 1/2”-wide filler panel or cleat set back even with front of case. CABINET CABINET 110° 120° Custom Panel Installation, Top View *For flush installation of ZDIS150 and ZDIC150 models: Install a 1/2"-wide filler strip on the hinge side.
Installation Instructions OPTIONAL ACCESSORIES ZPK1—Drain Pump Kit. For use when a floor drain is not available. The drain pump must be installed inside the unit and can operate at a maximum vertical height of 10 feet. 10 feet of tubing is supplied with the kit. ZIP75BB Black—For the installation of a trimless 3/4" thick custom panel on black models (not for stainless steel models). This kit provides a handle that can be installed with the custom panel.
Installation Instructions ADVANCE PLANNING ADVANCE PLANNING (cont.) CAUTION: Due to excessive weight, TWO PEOPLE ARE REQUIRED TO MOVE AND INSTALL THIS ICEMAKER. Failure to do so can result in back or other injury. Before you begin: 1. If a custom panel is to be installed, follow the instructions shown on pages 10 and 11. –Order ZIP75 (black) panel kit. –Order the custom panel from the cabinet manufacturer. –Secure the custom panel onto the icemaker. 2. Determine a method of drainage.
Installation Instructions REMOVE PACKAGING AND PARTS POWER SUPPLY WARNING: (Please read carefully). • Lay the carton on rear face and break open the bottom flap. • Set the carton upright with all four bottom flaps outward. • Lift carton up and off icemaker. • Remove all tape and packaging material from the outside and inside of the cabinet. FOR PERSONAL SAFETY, THIS APPLIANCE MUST BE PROPERLY GROUNDED. Failure to follow these instructions can result in death, fire or electrical shock.
Installation Instructions WATER SUPPLY WATER SUPPLY (cont.) • A cold water supply is required for icemaker operation. The water pressure must be between 30 and 120 p.s.i. • Route GE SmartConnect™ Kit or 1/4" O.D. copper tubing between house cold water line and the water connection location. • The water line should be long enough to extend to the back of the icemaker. Allow enough to accommodate moving unit forward for service.
Installation Instructions CONNECT WATER SUPPLY REVERSE THE DOOR SWING IMPORTANT: Disconnect power to the icemaker. • The water line should be flushed to clear any foreign material before connecting to the icemaker. • Connect the water line to the water supply tube outside of the rear access cover.
Installation Instructions REVERSE THE DOOR SWING (cont.) REVERSE THE DOOR SWING (cont.) Reverse the hinges (all models): • Remove the screws opposite the door hinges, top and bottom. Set aside. • Remove the two screws holding top hinge. • Turn the hinge upside down, with the hinge pin pointing up. Reinstall the hinge on the opposite side at the bottom of the door. • Remove the bottom hinge. Turn the hinge upside down and install on the opposite side at the top. • Remove the top hinge pin.
Installation Instructions for ZIP75BB Kit • BEFORE YOU BEGIN: NOTE: If installing a 3/4" trimless custom panel, a 1-1/2" wide filler strip may be required. The filler strip will act as a spacer between the icemaker case and the adjacent cabinet, and will prevent interference with the icemaker door swing when it is installed between frameless or framed cabinetry. The width of the cutout opening must include the width of the filler strip.
Installation Instructions for ZIP75BB Kit STEP 1 STEP 2 DISCONNECT POWER TO THE ICE MACHINE STEP 5 • Lay the custom panel appearance-side-down on a clean surface. • Align top and bottom side trim to the custom panel sides. REMOVE HANDLE AND NAMEPLATE • Remove the door handle by removing the two top mounting screws. Set screws aside. Discard handle. • The Monogram nameplate is held in place with adhesive. Remove the nameplate. STEP 3 • Tape the side trim pieces to the back of the custom panel.
NOTE: While performing installations described in this book, safety glasses or goggles should be worn. For Monogram® local service in your area, call 1.800.444.1845. NOTE: Product improvement is a continuing endeavor at General Electric. Therefore, materials, appearance and specifications are subject to change without notice. Pub. No. 31-46199-2 Part No.
