Installation Instructions Automatic Ice maker ZDIC150 ZDIS15 Design Guide With Installation Instructions monogram.com www.goedekers.
Installation Instructions • BEFORE YOU BEGIN: CONTENTS Read these instructions completely and carefully. • Design Information Models Available .................................................................... 3 Optional Accessories ........................................................... 3 Tools and Materials Required ........................................ 3 Cutout & Product Dimensions ......................................... 4 IMPORTANT: Save these instructions for local inspector’s use.
Design Information MODELS AVAILABLE ZDIS150HSSLH, ZDIS150HSSRH, and ZDIC150HBB Available in black and stainless steel. The ice maker may be installed below a countertop or used free-standing. OPTIONAL ACCESSORIES =,3 %%³For the installation of a trimless 3/4” thick custom panel on black models (not for stainless steel models). This kit provides a handle that can be installed with the custom panel. A custom handle of your choice may be installed onto the 3/4” panel.
Installation Instructions ADVANCE PLANNING CUTOUT & PRODUCT DIMENSIONS (Cont.) CAUTION: Due to excessive weight, TWO Cutout dimensions shown allow for a full door swing. Flush Installation, Top View PEOPLE ARE REQUIRED TO MOVE AND INSTALL THIS Ice maker. Failure to do so can result in back or other injury. MISE EN GARDE : A cause de son poids élevé, IL FAUT DEUX PERSONNES POUR DÉPLACER ET INSTALLER CETTE MACHINE À GLAÇONS.
Installation Instructions ADVANCE PLANNING (cont.) ADVANCE PLANNING (cont.) LOCATION REQUIREMENTS: • Not designed for outdoor installation. • The ice maker must be installed in an area protected from elements such as wind, rain, water spray or drip. The area should be ventilated with temperatures above 55°F (13°C) and below 110°F (43°C). Best results are obtained between 70°F (21°C) and 90°F (32°C).
Installation Instructions REMOVE PACKAGING AND PARTS POWER SUPPLY WARNING : (Please read carefully). • Lay the carton on rear face and break open the bottom flap. • Set the carton upright with all four bottom flaps outward. • Lift carton up and off ice maker. • Remove all tape and packaging material from the outside and inside of the cabinet. FOR PERSONAL SAFETY, THIS APPLIANCE MUST BE PROPERLY GROUNDED. Failure to follow these instructions can result in death, fire or electrical shock.
Installation Instructions ADJUST HEIGHT AND LEVEL THE ICE MAKER WATER SUPPLY SET-UP • A cold water supply with water pressure between 30 and 120 p.s.i. is required for ice maker operation. • 7R DOORZ VXȻFLHQW ZDWHU ÀRZ WR the ice maker, a minimum 1/2” diameter home supply line is recommended. Height adjustments may be necessary to install the ice maker below a countertop, and may be accomplished by adjusting both the front and rear leveling legs. The ice maker must be level to operate properly.
Installation Instructions CONNECT WATER SUPPLY TO APPLIANCE CONNECT WATER LINE (cont.) For GE SmartConnect™ Tubing: • Insert the molded end of the tubing into the ice maker connection. Tighten the compression nut until it is just hand tight. • Tighten one additional turn with a wrench. Overtightening can cause leaks! • Make sure there are no sharp bends or kinks that could restrict water flow. • The water line should be flushed to clear any foreign material before connecting to the ice maker.
Installation Instructions CONNECT DRAIN This ice maker is equipped with a gravity drain to prevent water from flowing back into the storage bin and Drain Hose overflowing onto 1” Min. Gap the floor. The ideal installation has a 1-7/8” standpipe with a 2” to 1-1/2” PVC drain 22” reducer installed directly 22-3/4” with 3/4” Custom Panel below the drain tube: –A 1” min. physical gap between the bottom of the ice maker drain hose and the top of the house drain is required. See illustration.
Installation Instructions REVERSE THE DOOR SWING (cont.) REVERSE THE DOOR SWING (Black Door Models Only) IMPORTANT: Disconnect power to the ice maker. STEP 2 - DOOR STOP AND END-CAP REVERSAL 1. Remove the hinge pin from the top hinge. 2. Remove the door from the hinges and replace the top hinge pin.
Installation Instructions REVERSE THE DOOR SWING (cont.) REVERSE THE DOOR SWING (cont.) STEP 3 - REVERSE HINGES STEP 4 - REPLACE DOOR 1. Unscrew hinge screws and remove the top hinge. Replace screws in empty hinge holes. 2. Remove screws from opposite side of ice maker cabinet. Turn top hinge upside down so the hinge pin points up. Place hinge on the bottom opposite side of ice maker and tighten screws. Align handle with the holes in the door and replace screws. Tighten. STEP 5 - REVERSE DOOR CATCH 1.
Installation Instructions for ZPK2 • BEFORE YOU BEGIN: KIT CONTENTS: Read these instructions completely and carefully. • • Auxiliary drain pump IMPORTANT: • Drain tube, 5/8” ID x 5-1/8” (bin to pump reservoir inlet) IMPORTANT: • Drain tube, 1/2” ID x 10’ (pump check valve to house drain) Save these instructions for local inspector’s use. • Observe all governing codes and ordinances. • Note to Installer – Be sure to leave these instructions with the Consumer.
Installation Instructions STEP 1 - REMOVE ORIGINAL PARTS STEP 2 - CONNECT ELECTRICAL NOTE: If pump is being installed on a ice maker that has not been completely installed, please proceed to Drain Pump Install section. 1. Position pump at the right side, just outside of the opening. 1. Unplug power cord from rear cover. 2. Remove screws holding the rear cover. Retain screws. Carefully pull rear cover away from drain tube.
Installation Instructions STEP 4 -INSERT DRAIN PUMP STEP 6 - SECURE VENT TUBE 1. Carefully slide the auxiliary drain pump into the bottom of the ice machine. The tab on the back of the pump should slip into the rectangular slot on the ice machine floor. It may be necessary to tip the pump slightly to engage the tab. 1. Place rear cover against the back of the ice machine. Route the vent tube, power cord, drain tube, and water supply line through cut outs in the rear cover.
Installation Instructions for ZIP75BB Kit • NOTE: If installing a 3/4” trimless custom panel, a 1-1/2” wide filler strip may be required. The filler strip will act as a spacer between the ice maker case and the adjacent cabinet, and will prevent interference with the ice maker door swing when it is installed between frameless or framed cabinetry. The width of the cutout opening must include the width of the filler strip.
Installation Instructions for ZIP75BB Kit STEP 1 DISCONNECT POWER TO THE ICE MACHINE STEP 5 SECURE SIDE TRIM PIECES TO CUSTOM PANEL 1. Lay the custom panel appearance-side-down on a clean surface. 2. Align top and bottom side trim to the custom panel sides. STEP 2 REMOVE HANDLE AND NAMEPLATE 1. Remove the door handle by removing the two top mounting screws. Set screws aside. Discard handle. 2. The Monogram nameplate is held in place with adhesive. Remove the nameplate. 3.
Notes 17 www.goedekers.
NOTE: While performing installations described in this book, safety glasses or goggles should be worn. For Monogram® local service in your area, call 1.800.444.1845. NOTE: Product improvement is a continuing endeavor at General Electric. Therefore, materials, appearance and specifications are subject to change without notice. Pub. No. 31-49006-2 Part No. 245D1420P001 GE Appliances & Lighting Appliances General Electric Company Louisville, KY 40225 GEAppliances.
