Installation Instructions 30", 36" and 48" Professional Ranges Cuisinières professionnelles de 30’’ (76 cm) 36" (91 cm) et de 48" (121 cm) Instructions d’installation La section française commence à la page 24 Cocinas profesionales de 30", 36" y 48" Instrucciones de instalación La sección en español empieza en la página 46 31-10689 04-08 JR
Installation Instructions BEFORE YOU BEGIN Vent hood Combinations: Read these instructions completely and carefully. It is recommended that these ranges be installed in conjunction with a suitable overhead vent hood. • Install a hood with at least 1200 CFM above a 48" wide range. • Install a hood with at least 600 CFM above a 30” or 36” range. Due to the high heat capacity of this unit, particular attention should be paid to the hood and ductwork installation to assure it meets local building codes.
Design Information Installation Instructions Step 1, Remove Packaging ..............................................11 Step 2, Move Range Indoors ..........................................12 Step 3, Install Anti-Tip Device ........................................13 Step 4, Connect Range to Gas........................................14 Step 5, Connect Electrical ................................................14 Step 6, Roll Range into Position ....................................14 Step 7, Level the Range .
Design Information PRODUCT DIMENSIONS AND CLEARANCES 48" Range Models Universal Utility Locations 1” Countertop to Cooking Surface 47-7/8” Width 8” 35-1/4” to 36-3/4” Height 6-1/2” 14” 16” Gas/ Electric Electric 3-1/4” to 4-3/4” 2” 2” 48” Toekick/leg Height 28-1/4” Depth to Front of Door 12” Minimum to Adjacent Wall 48” Minimum to Combustibles WARNING: Installations without a hood require 48” minimum to combustibles.
Design Information PRODUCT DIMENSIONS AND CLEARANCES 36" Range Models Universal Utility Locations 1” 35-7/8” Width Countertop to Cooking Surface 4-5/8” 35-1/4” to 36-3/4” Height 6-1/2” 13-3/8” 11-3/8” Gas/ Electric Electric 3-1/4” to 4-3/4” 2” 2” 36” 28-1/4” Depth to Front of Door Toekick/leg Height 12” Minimum to Adjacent Wall 48” Minimum to Combustibles WARNING: Installations without a hood require 48” minimum to combustibles.
Design Information PRODUCT DIMENSIONS AND CLEARANCES 30" Wide Range Models Universal Utility Locations 1” 29-7/8” Width Countertop to Cooking Surface 4-5/8” 35-1/4” to 36-3/4” Height 11-3/8” 7-3/8” Gas/ Electric Electric 6-1/2” 3-1/4” to 4-3/4” 2” 2” 30” 28-1/4” Depth to Front of Door Toekick/leg Height 12” Minimum to Adjacent Wall 48” Minimum to Combustibles WARNING: Installations without a hood require 48” minimum to combustibles.
Design Information PRODUCT DIMENSIONS AND CLEARANCES 48", 36" and 30" Range Models 10-1/2” 28-7/8” To Front Edge 13/16” Optional Backsplash Accessories 30-36” 12” 3-3/16” Control Panel Depth 1” 35-1/4” to 36-3/4” 28-1/4” To Beveled Edge of Control Panel Bullnose 7” Control Panel Height 27-1/2” To Beveled Edge – Maximum Adjacent Cabinet Depth for Flush Installation 28-1/4” To Front of Door 12" Min.
Installation Information TOOLS REQUIRED WB28K10553 HIGH ALTITUDE KIT For operation above 3,000 feet, order WB28K10553 Conversion Kit. This kit includes orifices for both LP and Natural gas operation. Drill and Appropriate Bits Saber Saw WB28K10554 DE-RATE KIT (For a small kitchen environment.) De-rate conversion kit for use with model ZDP304N (natural gas only). This kit includes orifices to reduce surface burner output to 40,800 BTU’s.
Installation Preparation POWER SUPPLY LOCATIONS Gas Supply: Electric Supply: •The natural gas models are designed to operate at 5" water column pressure. For proper operation, the pressure of the natural gas supplied to the regulator must be between 7" and 13" water column. •The LP models are designed to operate at 10" water column pressure. For proper operation, the pressure of the LP gas supplied to the regulator must be between 11" and 13" water column.
Installation Preparation 4-WIRE POWER CORD INSTALLATION 3-WIRE POWER CORD INSTALLATION NOTE: A 4-wire cord is connected to the range at the factory. Use the following steps to change an existing installation from a 3-wire cord back to a 4-wire cord. NOTE: A 4-wire cord is connected to the range at the factory. Use the following steps to change the range to a 3-wire cord.
Installation STEP 1 REMOVE PACKAGING CAUTION • Open oven door(s) and remove packaging. Remove shelf holding broiler pan, tape, literature package, shelf lubricant and probe. Stand clear. The ends of the cut metal banding may snap toward you. •Cut the metal banding. Lift the carton straight up. •Locate the two runner strips from the top of the packaging. These strips will be used to protect the kitchen floor during installation. •Remove corner posts. Dispose of packaging materials.
Installation Preparation STEP 2 MOVE THE RANGE INDOORS 4 Slide the blade of the hand-truck beneath the front and back legs. 1 Tilt the range forward on the skid. Toekick 2 Lift the toekick out of the foam base. Insert Blade Under the Range Legs IMPORTANT: Place the hand-truck straps below the oven door handles. 5 Tilt the range to lower the hand-truck wheels off the skid. Toekick Hand-Truck Straps Below Oven Door Handles 3 Tilt the range to one side and remove the foam block.
Installation STEP 3 INSTALL ANTI-TIP DEVICE • All ranges can tip. • BURNS or other SERIOUS INJURIES can result. • INSTALL and CHECK the ANTI-TIP bracket following these instructions. • Attach the Anti-Tip Brace onto the bottom of the range in the recessed area. Install 2 hex screws (provided) through the brace and into the range. To reduce the risk of tipping the range, the range must be secured by a properly installed anti-tip bracket.
Installation STEP 4 CONNECT RANGE TO GAS STEP 6 ROLL RANGE INTO POSITION WARNING WARNING Do not use a flame to check for gas leaks. The Anti-Tip Bracket must be properly installed to prevent tipping of the range. Failure to do so can cause serious damage or injury. • Check to be sure the appliance runners are beneath the wheels. • The range is shipped with the wheels in the down position.
Installation STEP 7 LEVEL THE RANGE STEP 7 WARNING LEVEL THE RANGE (cont.) REAR LEG ADJUSTMENT •Remove two screws from rear vent trim. Slide vent trim forward, then lift up to remove. •Find the two rear leg extension rods. Use a 1/4" driver or wrench to adjust the left or right rear legs. The range must be level and be supported by the legs—not the wheels. The range could move if the wheels make contact with the floor. Be sure all legs make contact with the floor in any installation.
Installation STEP 9 FINALIZE INSTALLATION CHECK BURNERS Place the burner grates over the burners. The grates should be seated and should not rock. Check to be sure that burner heads and caps are securely seated. The griddle is secured with screws. It is designed to be stationary and should not be removed. The griddle has two leveling screws beneath the rear flue cover that can be used to adjust to the desired slope.
Installation ACCESSORIES—TOEKICK (provided) •Install the toekick after the range has been leveled. •Measure the distance between the floor and the bottom of range. •Loosen the two screws on each end. Adjust the toekick height by sliding the upper and lower pieces apart to 1/8" less than the measured height. •Secure the top and bottom sections by tightening the 2 screws on each end. •Push toekick against range leg until clip snaps to legs. NOTE: Be sure the toekick snaps securely to the leg.
ZX12B30PSS, ZX12B36PSS, ZX12B48PSS Accessory Installation OPTIONAL ACCESSORIES—12" HIGH BACKSPLASH INSTALL 12" BACKSPLASH WARNING: WARNING: To prevent ignition of combustible materials, the entire back wall above the range must be protected by a backsplash constructed of non-combustible material. This backsplash must be securely fastened to the wall. Failure to do so could result in damage or personal injury.
ZXADJB30PSS, ZXADJB36PSS, ZXADJB48PSS Accessory Installation ACCESSORIES—30" TO 36" ADJUSTABLE BACKSPLASH (not included) INSTALL THE WALL SUPPORT PANELS WARNING: WARNING: To prevent ignition of combustible materials, the entire back wall above the range must be protected by a backsplash constructed of non-combustible material. The wall support panels must be securely fastened to the wall. Failure to do so could result in damage or personal injury.
ZXADJB30PSS, ZXADJB36PSS, ZXADJB48PSS Accessory Installation INSTALL COVER PANELS INSTALL COVER PANELS (cont.) See alternate method if side access is blocked. ALTERNATE METHOD: When side access is blocked • Hold the bottom cover over the bottom support while driving one screw (provided) into each side. • Place the top cover with shelf over the top wall support. If you have access to the sides, secure the panel with two screws on each side.
Installation Instructions Convert Natural Gas to LP Gas Operation Convert LP Gas to Natural Gas Operation 2 CONVERT THE REGULATOR WARNING: This conversion must be performed by a qualified installer or gas supplier in accordance with the manufacturer’s instructions and all codes and requirements of the authority having jurisdiction. Failure to follow instructions could result in serious injury or property damage. The qualified agency performing this work assumes responsibility for the conversion.
Installation Instructions for Gas Conversion 3 CHANGE BURNER ORIFICES (cont.) 4 CHANGE GRILL ORIFICE (if present) IMPORTANT: Find your model number below. Read each orifice label to identify and install them in the exact locations shown. Locate the 1–1/2” long Grill orifice. Select for your gas type. LP—.047, NAT—.067 ZDP304 SIMMER ORIFICES A. Remove the grill cover, grates and grate frame. Lift the radiant baffle straight up and off. A 34SL or 51SN orifice will be used on all burners.
Installation Instructions for Gas Conversion 6 ADJUST BURNER FLAMES 5 CHANGE GRIDDLE ORIFICE (if present) Locate the 3/4” long Griddle orifice. Select for your gas type. LP—.047, NAT—.076 Normally, burners do not need further adjustment. Make adjustments only when necessary. A. Lift off the griddle flue cover. Remove Griddle Flue Cover the 2 inside A clamping screws. B. Use a pad or piece of carton to protect Leveling Screws the adjacent surface.
NOTE: While performing installations described in this book, safety glasses or goggles should be worn. For Monogram® local service in your area, call 1.800.444.1845. NOTE: Product improvement is a continuing endeavor at General Electric. Therefore, materials, appearance and specifications are subject to change without notice. REMARQUE: lorsque vous procédez aux installations abordées dans ce manuel, il est fortement recommandé de porter des lunettes de sécurité.