INSTALLATION INSTRUCTIONS with Design Guide Wine Chiller, Wine Reserve and Beverage Center MONOGRAM.
Safety Information BEFORE YOU BEGIN Read these instructions completely and carefully. • IMPORTANT – Save these instructions for local inspector’s use. Observe all governing codes and ordinances. • Note to Installer – Be sure to leave these instructions with the Consumer. • Note to Consumer – Keep these instructions with your Owner’s Manual for future reference. WARNING If you received a damaged refrigerator, you should immediately contact your dealer or builder.
Consignes de Sécurité AVERTISSEMENT Risque d’explosion. Conservez les matériaux et vapeurs inflammables de votre réfrigérateur. Le non-respect de cette instruction peut entraîner un risque d’incendie, d’explosion ou de décès. AVERTISSEMENT 3RXU UpGXLUH OH ULVTXH G¶pWRXႇHPHQW SHQGDQW O¶LQVWDOODWLRQ GH FH SURGXLW QH SDV ODLVVHU OHV petites pièces à la portée des enfants âgés de moins de 3 ans. BRANCHEMENTS ÉLECTRIQUES AVERTISSEMENT Risque d’électrocution.
Design Guide CONTENTS Safety Information ...................................................2, 3 STAINING WOOD DRAWER FRONTS Design Guide Tools Required ..............................................................4 Parts Supplied ...............................................................4 Refrigerator Location .....................................................4 Staining Wood Drawer Fronts ......................................4 Installing Custom Frame Panel ....................................
Design Guide THE INSTALLATION SPACE SINGLE PRODUCT INSTALLATION F P N,O A J Std. Cabinet Opening K Min. Cabinet Opening G,I SIDE BY SIDE PRODUCT INSTALLATION D E H B,C P N,O NOTE: Handle and handle VWDQGRႇ GHSWK LV (Actual handle may vary slightly.
Design Guide For models ZDWI240, ZDWR240, ZDBI240, ZDBR240 THE INSTALLATION SPACE SIDE-BY-SIDE INSTALLATIONS All models may be used freestanding. For a complete refreshment center, Install a fresh food refrigerator beside a Double-Drawer refrigerator, Beverage Center, or Wine Chiller/Wine Reserve. • A side by side installation requires minimum width openings depending on if the product will be flush or standard mounted and if there are stainless or custom panels. See chart below.
Design Guide For Models ZDWR240 and ZDBR240 with Stainless Steel Door Panels and Handles for Flush and Standard Installation THE INSTALLATION SPACE PRODUCT CLEARANCES For a flush installation Install a 1/4”-wide filler strip on the hinge side. The filler strip will act as a spacer between the door case and adjacent cabinets and will prevent interference with the cabinet door swing.
Design Guide For Models ZDWI240 and ZDBI240 with Custom Door Panels and Handles for Standard Installation only THE INSTALLATION SPACE PRODUCT CLEARANCES Flush Installation not allowed with custom Door Panels and Handles The stainless steel wine chiller, wine reserve and beverage center is factory set for a 110° door swing. Models that accept custom panels have a 95° door swing. When installed in a corner: • Allow 16” minimum clearance on the hinge side for a full 110° door swing.
Installation Instructions STEP 1 REMOVE PACKAGING • Remove corner blocks and foam drawer stops. • Remove all packing material, tape and protective plastic coverings. • Remove stainless steel toekick taped to the back of the unit. WARNING Small objects are a choke hazard for children. Remove and discard any parts not used. AVERTISSEMENT Les petits objets peuvent étrangler les enfants. Il faut jeter toutes les pièces qui ne sont pas utilisées.
Installation Instructions STEP 2 REVERSE DOOR SWING (Cont.) Install Toekick The toekick has a cutout on the left and right sides. Remove the plug on the left side and reinstall on the right side. If you choose to install the stainless steel toekick, reinstall the plug on the right side of that toekick. • Install original screws and spacers or screws and spacers supplied with the stainless steel toekick. Install screws through the spacer VWDQGRႇ WRHNLFN DQG LQWR the base as shown.
Installation Instructions CUSTOM FRAME PANEL MODELS Model ZDWI240WII and ZDBI240WII These models require a custom panel frame surrounding the glass. There are two options: the panel may be 29 Ǝ RU Ǝ KLJK $ Ǝ SDQHO UHTXLUHV D QRWFK FXW LQWR WKH bottom of the panel to avoid interference with the hinges. • Rout the back side of the panel to the dimensions shown. • A custom handle of your choice or ZTBSS1 Tubular Handle must be installed before the panel is mounted onto the door.
NOTE: While performing installations described in this book, safety glasses or goggles should be worn. NOTE: Product improvement is a continuing endeavor at Monogram. Therefore, materials, appearance and specifications are subject to change without notice. 31-1000646 02-22 GEA Monogram.
