Installation Sheet

ManualsBrandsMonogram ManualsAppliances30 in. Radiant Electric Cooktop in Stainless Steel/Black with 5 Elements including SyncBurners

TOOLS YOU MAY NEED

CUTTING THE COUNTERTOP

If you are installing the cooktop in a solid surface

material such as granite, quartz or any other

natural or synthetic solid surface, we recommend

that the cutout be prepared by a professional

cabinet or countertop installer.

Cooktop cutouts in wood or wood-laminate

countertops may be able to be prepared using a

saber saw and electric drill.

MATERIALS YOU WILL NEEDBEFORE YOU BEGIN

Read these instructions completely and carefully.

•

IMPORTANT ³ Save these instructions

for local inspector’s use.

•

IMPORTANT ³Observe all governing

codes and ordinances.

•

Note to Installer – Be sure to leave these

instructions with the Consumer.

• Note to Consumer – Keep these instructions for

future reference.

• Product failure due to improper installation is not

covered under the Warranty.

WARNING ³ This appliance must be

properly grounded.

•

ATTENTION INSTALLER ³ALL

COOKTOPS MUST BE HARD WIRED (DIRECT

WIRED) INTO AN APPROVED JUNCTION BOX. A

“PLUG AND RECEPTACLE” IS NOT PERMITTED

ON THESE PRODUCTS.

• Proper installation is the responsibility of the

installer and product failure due to improper

installation is NOT covered under warranty.

Wire NutsJunction Box

Saber Saw

Pencil

Safety Glasses

1/8” Drill Bit & Electric or

Hand Drill

Ruler or Straightedge

Phillips Head

Screwdriver

If you have questions, call 800.GE.CARES or visit our website at: GEAppliances.com.

PARTS INCLUDED

2 Hold Down

Brackets

4 Screws

(WB01X1137)

Foam Tape

WB06K5042

90º or Straight

Squeeze Connector

for 1” Conduit

31-11025-1 07-16 GEA

Installation

Instructions

30 and 36"

Electric Cooktop - Radiant

Excludes Down-Draft Models

Summary of content (16 pages)

PAGE 1
Installation Instructions 30 and 36" Electric Cooktop - Radiant Excludes Down-Draft Models If you have questions, call 800.GE.CARES or visit our website at: GEAppliances.com. BEFORE YOU BEGIN MATERIALS YOU WILL NEED Read these instructions completely and carefully. • IMPORTANT ³ Save these instructions for local inspector’s use. • IMPORTANT ³ Observe all governing codes and ordinances. • Note to Installer – Be sure to leave these instructions with the Consumer.
PAGE 2
Installation Instructions IMPORTANT SAFETY INSTRUCTIONS FOR YOUR SAFETY ELECTRICAL REQUIREMENTS • For Personal Safety, remove house fuse or open circuit breaker before beginning installation. Failure to do so could result in serious injury or death. • Be sure your cooktop is installed properly by a qualified installer or service technician. • To eliminate the risk of burns or fire due to reaching over heated surface elements, cabinet storage located above the surface units should be avoided.
PAGE 3
Installation Instructions PRE-INSTALLATION CHECKLIST WARNING – The electrical power to the cooktop supply line must be shut off while connections are being made. Failure to do so could result in serious injury or death. A When preparing cooktop opening, make sure the inside of the cabinet and the cooktop do not interfere with each other. (See section on preparing the opening.) B Remove packaging materials and literature package from the cooktop before beginning installation.
PAGE 4
Installation Instructions PREPARING THE OPENING 1 APPROXIMATE COOKTOP DIMENSIONS 3 MINIMUM CLEARANCES TO ADJACENT WALLS & CABINETS Y X Z Cooktop 30” models: 28 1/16” 36” models: 33 3/4” 30” models: 19 1/4” 36” models: 18 7/8” Size 30” 36” Models JP3030T, D, JP3530T, D JP3030SJSS, JP3530SJSS JP5030D, PP7030D, PP7030E, CP9530S JP5030S, PP7030S, PP9030S ZEU30RS PP9036S, D ZEU36RSJSS JP5036S, D JP3536S, T, D X 29 3/4” Y 20 7/8” Z Front 3 1/4 ” Z Rear* 4” 29 7/8” 21” 3 1/4” 4” 29 3/4” 20 7/8”
PAGE 5
Installation Instructions PREPARING THE OPENING (Cont) 5 VERTICAL CLEARANCE Allow 5” minimum 8-1/4" vertical clearance from the cooktop bottom (or 8-1/4” minimum depth from the countertop) to any combustible surfaces, such as a cabinet drawer. 6 For Americans with Disabilities Act (ADA) Forward Approach Installation Only: 5" DRAWER 5" For models with no drop box, allow 5” minimum depth between the countertop and an enclosure.
PAGE 6
Installation Instructions INSTALLING THE COOKTOP 1 INSTALLING THE JUNCTION BOX Install an approved junction box where it will be easily reached through the front of the cabinet where the cooktop will be located. The cooktop conduit is 4 feet long. 3 ATTACH FOAM TAPE Apply the foam tape around the outer edge of the glass. Do not overlap the foam tape. Bottom of Cooktop Foam Tape 16” Min. Install junction box so that it can be reached through the front of the cabinet.
PAGE 7
Installation Instructions INSTALLING THE COOKTOP (CONT.) 4 MOUNTING PARTS (Cont.) Alternate Installation: You can order an alternate installation kit WB01X24570 with wing nuts and brackets by calling 800.GE.CARES. See diagram for instructions. Open the cabinet door. Install the second screw through the bracket and tighten. Then tighten the first screw. Install thumbscrew until it touches the bottom of the countertop.
PAGE 8
Installation Instructions ,167$//$7,21³(/(&75,&$/ &211(&7,216 GROUNDING INSTRUCTIONS: The ground wire in the conduit is connected to the cooktop frame. Effective January 1, 1996, the National Electrical Code will not permit grounding through neutral.
PAGE 9
Instrucciones Estufa eléctrica de y 30” Radiante de instalación 36” Excluye los Modelos de Flujo Descendente “Si tiene alguna pregunta, llame al 800.GE.CARES o visite nuestro sitio Web en: GEAppliances.com” ANTES DE COMENZAR Lea estas instrucciones por completo y con cuidado. • NECESITARÁ LOS SIGUIENTES MATERIALES IMPORTANTE ³ Conserve estas instrucciones para el uso del inspector local. • IMPORTANTE ³ Cumpla con todos los códigos y reglas aplicables.
PAGE 10
Instrucciones de instalación INSTRUCCIONES DE SEGURIDAD IMPORTANTES PARA SU SEGURIDAD REQUISITOS ELÉCTRICOS • Para su seguridad personal, retire los fusibles de su hogar o bien desconecte el cortacircuitos antes de comenzar con la instalación. El no hacerlo puede resultar en lesiones serias o incluso la muerte. • Asegúrese que su estufa sea instalada correctamente por un instalador o técnico de servicio calificado.
PAGE 11
Instrucciones de instalación LISTA DE VERIFICACIÓN PREVIA A LA INSTALACIÓN ADVERTENCIA – La corriente eléctrica a la linea de abastecimiento de la estufa debe cortarse durante la realización de conexiones. El no hacerlo puede resultar en una lesión seria o la muerte. A B Cuando se prepare para la abertura de la estufa, asegúrese que el interior del gabinete y la estufa no interfieran uno con el otro. (Consulte la sección de preparación de la abertura).
PAGE 12
Instrucciones de instalación PREPARACIÓN DE LA ABERTURA 1 DIMENSIONES GENERALES DE LA SUPERFICIE DE COCCIÓN Y X Z Estufa 30” modelos: 28 1/16” 36” modelos: 33 3/4” 30” modelos: 19 1/4” 36” modelos: 18 7/8” Tamaño Modelos X Y Z Frente Z Parte Trasera* 30” JP3030T, D, JP3530T, D 29 3/4” 20 7/8” 3 1/4 ” 4” JP3030SJSS, JP3530SJSS 29 7/8” 21” 3 1/4” 4” JP5030D, PP7030D, PP7030E, CP9530S 29 3/4” 20 7/8” 3 9/16” 5 9/16” JP5030S, PP7030S, PP9030S 29 7/8” 21” 3 9/16” 5 9/16” ZEU30RS
PAGE 13
Instrucciones de instalación PREPARACIÓN DE LA ABERTURA (Cont) 5 ESPACIOS LIBRES VERTICALES Deje un espacio vertical de por lo menos 5” desde la parte inferior de la placa de cocción (o una profundidad mínima de 8-1/4” desde la mesada) hasta cualquier superficie combustible, tal como el cajón de un gabinete.
PAGE 14
Instrucciones de instalación INSTALACIÓN DE LA ESTUFA 1 INSTALACIÓN DE LA CAJA DE CONEXIONES Instale una caja de conexiones aprobada en un lugar de fácil acceso a través del frente del gabinete en donde pueda colocarse la estufa. El conducto de la estufa tiene 4 pies de longitud. 3 APLIQUE LA CINTA DE ESPUMA Aplique la cinta de espuma alrededor del borde externo del vidrio. No superponga la cinta de espuma. Parte inferior de la estufa Cinta de espuma 16” Mín.
PAGE 15
Instrucciones de instalación INSTALACIÓN DE LA ESTUFA (CONT.) 4 LAS PARTES DE MONTAJE (Cont.) Instalación alternativa: Usted puede ordenar un kit de instalación alternativa WB01X24570 con tuercas mariposa y soportes llamando al 800.GE.CARES. Para acceder a instrucciones, consulte el diagrama. Abra la puerta del gabinete. Instale el segundo tornillo a través del soporte y ajuste. Luego ajuste el primer tornillo. Instale el tornillo de mariposa hasta que toque la parte inferior de la mesada.
PAGE 16
Instrucciones de instalación INSTALACIÓN³&21(;,21(6 (/e&75,&$6 INSTRUCCIONES PARA DESCARGA A TIERRA: El cable de descarga a tierra en el conducto se conecta al armazón de la estufa. A partir del 1 de enero de 1996, el Código Nacional sobre Electricidad no permitirá la descarga a tierra a través de cables neutrales.