Installation Guide

ManualsBrandsMonogram ManualsGas RangesMonogram 30" Liquid Propane Professional Range With 4 Burners

CHANGE BURNER ORIFICES

IMPORTANT: Find your model number below. Read

each orifice label to identify and install them in the

exact locations shown.

Replace the main burner orifice on all burners

as indicated.

Replace the burner heads, caps and top grates

Installation

Instructions

WB28K10553 High Altitude Kit

For Monogram Professional Range and Rangetop Installations

at Elevations of 6,000 Feet or More Above Sea Level

WARNING: This conversion must be

performed by a qualified installer or gas supplier in

accordance with the manufacturer’s instructions and

all codes and requirements of the authority having

jurisdiction. Failure to follow instructions could result

in serious injury or property damage. The qualified

agency performing this work assumes responsibility

for the conversion.

This kit is designed for both LP and Natural Gas range

and rangetop models. Use only the orifices specified.

Additional orifices may be present.

Keep all orifices and parts that are removed for

possible future use.

TOOLS YOU NEEDED FOR CONVERSION

Safety Glasses

Small Flat-Head Screwdriver

(2 to 2.4 mm or 3/32” tip size,

60 mm long)

1/4” and 7mm Nutdrivers

Small Pliers

1/2” Deepwell

Socket Wrench

Philips

Screwdriver

CHANGE BURNER ORIFICES

INSTALLATION TIP: The orifices for

ranges and rangetops operating on

either gas type—Natural or LP—are

included in this kit. Select and use only

the orifices specified for the type of

gas being used.

A. Remove the burner grates, burner

caps and burner heads.

B. Change only the main burner

orifices. The main orifice is located in

the center of the burner. The simmer

orifice is located higher beside the

center of the burner. Do not change

the simmer orifice.

NOTE: Models equipped with a grill do not require a grill

orifice change.

Burner Cap

Burner

Head

Spark

Igniter

Burner Base

Main

Orifice

Simmer

Orifice

31-10698-3 11-10 GE

30” LP Range Model ZDP304L and ZGP304L

Use 77HXL orifice

on three burners

for LP model

ZDP304L and

ZGP304L.

DO NOT

CHANGE THESE

NATURAL GAS

ORIFICES.

Use a 175HXN

orifice for the

right-front

burner.

30” Natural Gas Range Model ZDP304N and ZGP304N

ZDP364, ZDP366, ZDP484, ZDP486, ZGP364,

ZGP366, ZGP484, ZGP486, ZGU364, ZGU366,

ZGU484, ZGU486

MAIN

ORIFICES

Use 99HXL or

175HXN orifices

for all burners.

ALL 36” AND 48” RANGE OR RANGETOP MODELS:

Use a 99HXL

orifice for the

right-front

burner.

Summary of content (4 pages)

PAGE 1
Installation Instructions WB28K10553 High Altitude Kit For Monogram Professional Range and Rangetop Installations at Elevations of 6,000 Feet or More Above Sea Level WARNING: This conversion must be performed by a qualified installer or gas supplier in accordance with the manufacturer’s instructions and all codes and requirements of the authority having jurisdiction. Failure to follow instructions could result in serious injury or property damage.
PAGE 2
3 CHANGE GRIDDLE ORIFICE 4A CHANGE MAIN BAKE BURNER ORIFICE (if present) (if present) Locate the 3/4” long griddle orifice. Select the proper orifice size for your gas and burner from the conversion chart. A. Lift off the griddle flue cover. Remove the 2 inside clamping screws. Locate the 3/4” long bake burner orifice. Select the proper orifice size for your gas and burner from the conversion chart. A. Remove the oven door and set aside in a safe location. B.
PAGE 3
4B CHANGE COMPANION BAKE BURNER ORIFICE (if present) 5 ADJUST BURNER FLAMES Normally, burners do not need further adjustment. Make adjustments only when necessary. Locate the 3/4” long bake burner orifice. Select the proper orifice size for your gas and burner from the conversion chart. Hold-Down A. Remove the oven Screws door and set aside in a safe location. B. Remove the 2 oven bottom hold-down Oven screws from the Bottom rear of the cover. C. Slide the oven bottom forward and set asside. D.
PAGE 4
BURNER OUTPUT RATINGS: BTU/HR NG (Natural) Gas, 5” W.C.P. MODEL ZDP48, ZGP48, ZGU48 ZDP36, ZGP36, ZGU36 ZDP304 ZGP304 BURNER ALL SURF. Main BURNERS Simmer RF BURNER Main Simmer Main Simmer ORIFICE SIZE ID 16,800 0.075” (1.90mm) 175HXN 1,200 0.002” (0.51mm) 51SL 16,800 0.075” (1.90mm) 175HXN 1,200 0.002” (0.51mm) 51SN 8,800 0.050” (1.26mm) 126HXN 1,200 0.002” (0.51mm) 51SN ZDP304 ZGP304 RR, LR, LF ALL GRILL 15,000 0.0689” (1.