Quick Specification
HELPFUL TIPS
Product Specication Revised 6/20
For questions about your
appliance, please call 1-800-626-2000.
PAGE 3 OF 5
STANDARD INSTALLATION
ANTI-TIP BRACKET
ZICS360NXLH
Use two
additional hole
locations at
end of
brackets
Wall
Studs
Bracket
mounted
into vertical
wall studs
C
Ensure holes
selected are
centered on
the studs
L
FRONT VIEW OF CUTOUT
WITH ANTI-TIP BRACKET
35 1/2" (90.2)
2 5/16"
(5.9)
*84
+
-
.500
(212.1-214.6)
*Trim will overlap
additional 7/16"
3 1/2"
(8.9)
75"
(190.5 )
From floor
to bottom
of electrical
area
SIDE VIEWFRONT VIEW
ELEC.
6"
(15.2)
10"
(25.4)
23 5/8" (60)
2 3/8"
(6)
4 7/16"
(11.3)
7/16
"
(1.1)
Trim overlap
SIDE VIEW INSTALLED
WITH ANTI-TIP BRACKET
WATER
5"
(12.7)
5"
(12.7)
3 1/2"
(9.0)
WATER
10" (25.4)
81 1/2"
(207.0)
ZICS360NXLH
Use two
additional hole
locations at
end of
brackets
Wall
Studs
Bracket
mounted
into vertical
wall studs
C
Ensure holes
selected are
centered on
the studs
L
FRONT VIEW OF CUTOUT
WITH ANTI-TIP BRACKET
35 1/2" (90.2)
2 5/16"
(5.9)
*84
+
-
.500
(212.1-214.6)
*Trim will overlap
additional 7/16"
3 1/2"
(8.9)
75"
(190.5 )
From floor
to bottom
of electrical
area
SIDE VIEWFRONT VIEW
ELEC.
6"
(15.2)
10"
(25.4)
23 5/8" (60)
2 3/8"
(6)
4 7/16"
(11.3)
7/16
"
(1.1)
Trim overlap
SIDE VIEW INSTALLED
WITH ANTI-TIP BRACKET
WATER
5"
(12.7)
5"
(12.7)
3 1/2"
(9.0)
WATER
10" (25.4)
81 1/2"
(207.0)
A
B
A
Mounting the junction box in this
location will also allow for front
accessibility through access panel.
B
Water supply area.
WARNING:
The refrigerator is top heavy and
must be secured to prevent the
possibility
of tipping forward. Failure to do so
may result in death or serious injury.
The information below is for
cabinet design only. When
installing the
anti-tip system you must use the
product installation instructions.
The information below applies to all
installation constructions:
• A wall bracket, bolts and toggles
will be supplied with the unit.
• The bolts will be used to attach
bracket to wall in 4 locations. Two
of the locations must penetrate the
center of the wall studs.
• The toggles are used for stability in
drywall and when metal studs are
encountered. Lag bolts are used in
wood studs.
• In installation opening, measure
81-1/2" from oor and draw a
horizontal line.
• Locate and mark the wall studs on
horizontal line. Verify at least two
studs have their centerlines within
the center 32-1/2" of installation
opening to ensure 2 wall studs are
penetrated.
• The bracket will be centered left
to right in opening with bottom of
bracket on the horizontal line.
• When unit is placed in opening,
the bracket tabs will align with
openings in back of the unit. The
unit will be secured to the bracket
using supplied “L” bolts.
See Installation Instructions for
detailed instructions.