quick specs

Product Specication Revised 5/20
• A separate 115V, 60Hz, 15- or 20-amp power supply is
recommended for each product. Additional cutout width
may be required when side panels are used.
• In a side-by-side installation of a left-and-right-hand door
swing product, 1" clearance between the units is required.
Order ZGUSS2 European, ZGUPP2 Professional or ZGU2
custom panel unified grille kit for one continuous grille panel.
• In a side-by-side installation with same door swing, allow
2" minimum clearance between the products to prevent the
door swing interference. Allow 15" minimum to a wall to
achieve full drawer extension and pan removal. Additional
clearances are required when using custom panels and
handles. NOTE: ZGU2, ZGUSS2 or ZGUPP2 grille panel
kits will not fit this installation.
• In a side-by-side installation with right and left door
hinges together, allow 5" minimum clearance between the
two products to prevent one door from striking the other.
Additional clearance required wen using custom panels and
handles. NOTE: ZGU2, ZGUSS2 or ZGUPP2 grille panel
kits will not fit this installation.
PAGE 3 OF 8
For questions about your
appliance, please call 1-800-626-2000.
FRONT VIEW
SIDE VIEW
W
24" (61.0)
2"
(5.1)
4 3/4"
(12.1)
7/16" (1.1)
Trim overlap
3 1/2"
(8.9)
E
WATER
47 1/2" (120.7)
20" (50.8)
*83 1/2" min
*84 1/2" max
(212.1-214.6)
*Trim will overlap
additional 7/16"
3 1/2"
(8.9)
75"
(190.5)
From floor
to bottom
of electrical
area
6"
(15.2)
5"
(12.7)
5"
(12.7)
5"
(12.7)
ZISP480DXSS
SIDE VIEW INSTALLED
UNDER SOFFIT
SOFFIT
SIDE VIEW INSTALLED
WITH WOODEN WALL STUDS
AND NO SOFFIT
*84"
(213.4)
*Or installation
height from floor
2" x 4"
Cut to 35" Length
Screws mounted
into vertical wall
studs
Top Case Trim
3/4"
Min.
Side View Top
Case Trim
Install Screws
Through Trim and Into
3/4" Min. Wood Brace
FRONT VIEW INSTALLED
WITH METAL WALL STUDS
AND NO SOFFIT
SIDE VIEW
24"
(60.9)
COLUMNS RETROFIT
3 1/2"
(8.9)
Finished
Return
Back
3/4"
(1.91)
W
SIDE VIEW
24" (60.9)
COLUMNS RETROFIT
3 1/2"
(8.9)
Finished
Return
Back
3/4"
(1.91)
W
MONOGRAM 48" BUILT-IN
COLUMNS RETROFIT
HELPFUL TIPS
C
A minimum 3 1/2" (8.9) finished return matching cabinet
exterior recommended on interior on all sides and top at
front of opening
• In a side-by-side installation of a left-and-right-hand
door swing product, minimum 1/2" clearance between the
units is required. Also required is Side-by-Side Heater/
Dual Installation Kit, ZKUN, 48" trim kit ZKR48N and 48"
stainless toekick ZKR48N.
For retro fit installations, both units can be plugged into the
same electrical supply receptacle.
STANDARD INSTALLATION
WARNING:
When installing appliance, you must use and follow
the product installation instructions. ese can be found
with unit or on web at monogram.com.
is document is intended for cabinet and panel
construction only.
ATTENTION ELECTRICIAN:
A 115 volt 60Hz., 15 or 20 amp supply is recommended
for each product. An individual properly grounded branch
circuit or circuit breaker is recommended. Install a
properly grounded 3-prong electrical receptacle recessed
into the back wall. Electrical must be located on rear wall
as shown.
C
e refrigerator will project forward, slightly beyond adjacent cabinetry.