Retrofit Quick Specification

Product Specication Revised 6/20
• A separate 115V, 60Hz, 15- or 20-amp power supply is
recommended for each product. Additional cutout width
may be required when side panels are used.
• In a side-by-side installation of a left-and-right-hand door
swing product, 1" clearance between the units is required.
Order ZGUSS2 European, ZGUPP2 Professional or ZGU2
custom panel unied grille kit for one continuous grille
panel.
• In a side-by-side installation with same door swing,
allow 2" minimum clearance between the products
to prevent the door swing interference. Allow 15"
minimum to a wall to achieve full drawer extension
and pan removal. Additional clearances are required
when using custom panels and handles. NOTE: ZGU2,
ZGUSS2 or ZGUPP2 grille panel kits will not t this
installation.
• In a side-by-side installation with right and left door
hinges together, allow 5" minimum clearance between
the two products to prevent one door from striking
the other. Additional clearance required wen using
custom panels and handles. NOTE: ZGU2, ZGUSS2 or
ZGUPP2 grille panel kits will not t this installation.
PAGE 3 OF 8
For questions about your
appliance, please call 1-800-626-2000.
FRONT VIEW
SIDE VIEW
W
24" (61.0)
2"
(5.1)
4 3/4"
(12.1)
7/16" (1.1)
Trim overlap
3 1/2"
(8.9)
E
WATER
47 1/2" (120.7)
20" (50.8)
*83 1/2" min
*84 1/2" max
(212.1-214.6)
*Trim will overlap
additional 7/16"
3 1/2"
(8.9)
75"
(190.5)
From floor
to bottom
of electrical
area
6"
(15.2)
5"
(12.7)
5"
(12.7)
5"
(12.7)
ZISP480DXSS
SIDE VIEW INSTALLED
UNDER SOFFIT
SOFFIT
SIDE VIEW INSTALLED
WITH WOODEN WALL STUDS
AND NO SOFFIT
*84"
(213.4)
*Or installation
height from floor
2" x 4"
Cut to 35" Length
Screws mounted
into vertical wall
studs
Top Case Trim
3/4"
Min.
Side View Top
Case Trim
Install Screws
Through Trim and Into
3/4" Min. Wood Brace
FRONT VIEW INSTALLED
WITH METAL WALL STUDS
AND NO SOFFIT
SIDE VIEW
24"
(60.9)
COLUMNS RETROFIT
3 1/2"
(8.9)
Finished
Return
Back
3/4"
(1.91)
W
SIDE VIEW
24" (60.9)
COLUMNS RETROFIT
3 1/2"
(8.9)
Finished
Return
Back
3/4"
(1.91)
W
MONOGRAM 48" BUILT-IN
COLUMNS RETROFIT
HELPFUL TIPS
C
A minimum 3 1/2" (8.9) nished return matching
cabinet exterior recommended on interior on all sides
and top at front of opening
• In a side-by-side installation of a left-and-right-hand
door swing product, minimum 1/2" clearance between
the units is required. Also required is Side-by-Side
Heater/Dual Installation Kit, ZKUN, 48" trim kit
ZKR48N and 48" stainless toekick ZKR48N.
For retro fit installations, both units can be plugged into
the same electrical supply receptacle.
STANDARD INSTALLATION
WARNING:
When installing appliance, you must use and follow
the product installation instructions. These can be
found with unit or on web at monogram.com.
This document is intended for cabinet and panel
construction only.
ATTENTION ELECTRICIAN:
A 115 volt 60Hz., 15 or 20 amp supply is
recommended for each product. An individual
properly grounded branch circuit or circuit breaker is
recommended. Install a properly grounded 3-prong
electrical receptacle recessed into the back wall.
Electrical must be located on rear wall as shown.
C
The refrigerator will project forward, slightly beyond adjacent cabinetry.