INSTALLATION INSTRUCTIONS 18”, 24”, 30” and 36” Built-In Column Freezers 24”, 30” and 36” Built-In Column Refrigerators Pour obtenir une version française de ce manuel, visitez notre site web sur monogram.com. Para consultar una version en español de este manual de instrucciones, visite nuestro sitio de internet monogram.com. MONOGRAM.
Safety Information BEFORE YOU BEGIN If you received a damaged unit, you should immediately contact your dealer or builder. Read these instructions completely and carefully. • IMPORTANT – Save these instructions for Skill Level – Installation of this unit requires basic local inspector’s use. Observe all governing codes and ordinances. • Note to Installer – Be sure to leave these instructions with the Consumer. • Note to Consumer – Keep these instructions with your Owner’s Manual for future reference.
Safety Information AVANT DE COMMENCER Veuillez lire toutes ces instructions attentivement. • Niveau de compétence – L’installation de cet appareil exige des compétences de base en mécanique, menuiserie et plomberie. La responsabilité d’une installation adéquate relève de l’installateur. La garantie Monogram ne couvre pas les défectuosités du produit causées par une installation inadéquate. Consultez le manuel d’utilisation pour des renseignements sur la garantie.
Safety Information ANTES DE COMENZAR Si la unidad que recibió está dañada, se deberá comunicar de inmediato con su vendedor o fabricante. Lea estas instrucciones en su totalidad y atentamente. • • • IMPORTANTE – Conserve estas instrucciones para uso del inspector local. Cumpla con todos los códigos y ordenanzas gubernamentales. Nota para el Instalador – Asegúrese de que el Comprador conserve estas instrucciones.
Contents Safety Design Guide Dimensions and Clearances Accessories/Kits 2 6 7 Reversing the Door Swing Step 1. Remove Upper Enclosure Step 2. Remove Door Step 3. Move Control Assembly Step 4. Move Light Switch Housing Step 5. Reinstall Hinge Brackets Step 6. Reinstall the Enclosure Step 7. Reinstall the Front Access Cover Step 8. Remove Hinges from Door Step 9. Panel Brackets and Hinges Step 10.
Design Guide DIMENSIONS AND CLEARANCES Dimensions in parentheses are in centimeters. Overall Dimensions C A D O S TOP VIEWS B 15"(38.1) Minimum to a wall (16-9/16"(42.1 cm) on 30" models) (19" (48.3 cm) on 36" models) 5-1/8" (13.0) Minimum to a Wall 83-3/8" 83-1/4" (211.77) (211.46) B F E DOOR OPEN 90Û DOOR OPEN 115Û DIMENSIONS BASED ON HANDLE HEIGHT OF 2-9/16” (6.5) 4" (10.
Design Guide 7KH 0RQRJUDP &ROXPQV UHIULJHUDWRUV DQG IUHH]HUV FDQ EH LQVWDOOHG LQ PDQ\ FRQ¿JXUDWLRQV ZLWK GLႇHUHQW LQVWDOODWLRQ situations. Three installation situations will be explained along with door reversal instructions and two options for door panel installation. Reversing the Door Swing (all installation types) Making a refrigerator LH swing and freezer RH swing. MUST be done BEFORE the unit is removed from the shipping skid.
Reversing the Door Swing This step can be done for all installation types. 8 31-1000600 Rev.
Installation Instructions - Reversing the Door Swing STEP 1 REMOVE UPPER ENCLOSURE Compartment Door WARNING Follow all steps when reversing the door swing. Failure to follow these instructions, leaving off parts, or overtightening screws, can lead to the door falling off and result in injury and property damage. Ŷ Open the front cover of the enclosure to 90°. Locate filter and filter removal tool. Filter should be as shown.
Installation Instructions - Reversing the Door Swing STEP 2 REMOVE DOOR Ŷ Open the door to the open position. Ŷ Remove the 2 T30 Torx screws securing the top hinge to the case. Ŷ Have a second person support the open door. Ŷ Place the door on a protected work surface (to prevent scratches), liner side down. Ŷ Remove 2 T30 Torx screws securing the bottom hinge to the case. NOTICE: Door hinges will remain in the open position during the door reversal procedure.
Installation Instructions - Reversing the Door Swing STEP 3 MOVE CONTROL ASSEMBLY STEP 3 MOVE CONTROL ASSEMBLY (Cont.) Ŷ Remove upper hinge brackets by removing the T-30 Torx screws. Ŷ Snap glass assembly back onto the control housing assembly, ensuring plastic pins snap into holes on the side of the housing. T-30 Torx screws Upper Hinge Bracket STEP 4 MOVE LIGHT SWITCH HOUSING Ŷ Remove front access cover from unit by removing two 1/4” hex head screws.
Installation Instructions - Reversing the Door Swing STEP 4 MOVE LIGHT SWITCH HOUSING (Cont.) STEP 5 REINSTALL HINGE BRACKETS Ŷ Move the mounting bracket to the other side of the unit by removing two Philips screws and using them to install the bracket in its new location. Ŷ Move top hinge bracket to bottom and bottom bracket to top. Ŷ Ensure the 2 rectangular slots of bracket are on outside, hinge side of case.
Installation Instructions - Reversing the Door Swing STEP 6 REINSTALL THE ENCLOSURE (Cont.) STEP 8 REMOVE HINGES Bottom Hinge Cover Ŷ ,QVHUW ¿OWHU LQWR SRVLWLRQ DQG URWDWH ó WXUQ FORFNZLVH XVH ¿OWHU UHPRYDO WRRO LI QHHGHG WARNING Door Hinge Pinch Point Hazard Door hinges are under tension and should be left in the open position throughout the reversal process. Closing the hinge can lead to a finger pinch point hazard.
Installation Instructions - Reversing the Door Swing STEP 9 REMOVE HINGES FROM DOOR STEP 11 REINSTALL THE DOOR WARNING Follow all steps when reversing Ŷ Move the hinge assembly to the opposite end of the door - top hinge to the bottom and bottom hinge to the top. Hinge, L-bracket already attached to hinge, and support bracket will all move together. the door swing.
Instructions for Dual Integrated Installation New construction installation with 25” deep openings 31-1000600 Rev.
Design Guide - Dual Integrated Installation DUAL INTEGRATED INSTALLATION SPACE Dimensions in parentheses are in centimeters. 25" (63.5) Enclosure Width (See Chart) 6" (15.2) Finished Return 84" (213.4) C A D B ELECTRIC WATER 2 1/2" (6.4) LH RH 18 36 8 30 18 24 24 36 24 24 30 30 36 30 24 36 30 36 ENCLOSURE WIDTH A B C 53 1/2 4 1/8 3 1/2 7 1/2 2 26 9 36 9 135.9 10.5 8.9 19.1 5.1 66.0 22.9 91.4 22.9 47 1/2 4 1/8 3 1/2 7 1/2 2 22 1/8 5 28 6 1/4 120.
Design Guide - Dual Integrated Installation DUAL INTEGRATED INSTALLATION SPACE Water And Electrical Locations Electrical and water supply must be located as shown. For a 90° door swing, allow 4” (10.2 cm) minimum clearance to a wall. Additional Specifications • A separate 115 volt 60Hz., 15 or 20 amp power supply is recommended for each product. An individual properly grounded branch circuit or circuit breaker is recommended.
Installation Instructions - Dual Integrated Installation KIT ZKUN PARTS SUPPLIED: FLOORING Adhesive Heater Transformer Front Mullion Trim Bracket Top Unification Bracket Bottom Front Unification Bracket 3 1/4” Hex Head 8-18 5/8” Long Screws 5 1/4” Hex Head 8-32 5/8” Long Screws 5 3/8” Hex Head 1/4-20 1/2” Long Screws 4 wire clips For proper installation, this product must be placed on a level surface of hard material that is at the same height as the rest of the flooring.
Installation Instructions - Dual Integrated Installation STEP 1 REMOVE PACKAGING STEP 2 INSTALL WATER LINE Ŷ Remove front access cover from unit by removing two 1/4” hex head screws. (Some models have access cover in a box on the left side of the cabinet.) Place the cover and screws to the side for future installation. Ŷ Remove three 3/8” drive screws and two 7/16” drive WARNING ELECTRIC SHOCK HAZARD Attach tubing clamp using existing hole only. DO NOT drill into the refrigerator.
Installation Instructions - Dual Integrated Installation STEP 3 PREPARING UNIT FOR INSTALLATION STEP 3 PREPARING UNIT FOR INSTALLATION Ŷ Unpack the heater Unification Kit (ZKUN) and make sure all of the components on the list are included. NOTE: Ensure the heater connector cord is toward the top of the unit when installed. Ŷ Place the right hand unit in front of the installation opening in a way that the unit is in front of the intended installed location.
Installation Instructions - Dual Integrated Installation STEP 4 INSTALL ANTI-TIP BRACKET WARNING STEP 4 INSTALL ANTI-TIP BRACKET (Cont.) Ŷ Measure and mark from the RH side of the opening per the table above depending on the size of the RH unit you are installing. Tip Over Hazard. These appliances are top heavy, especially with any doors open, and must be secured to prevent tipping forward which could result in death or serious injury.
Installation Instructions - Dual Integrated Installation STEP 5 JOINING DUAL INSTALLED UNITS BOTTOM BACK UNIFICATION TOP UNIFICATION Ŷ Loosen the two bottom screws of rear access covers of both units and remove the top screws. Ŷ Loosen the front two screws on top of the unit and remove the two middle screws. Ŷ Hang the unification bracket to the bottom screws and reassemble the screws at the top Ŷ Assemble the bracket to the front screws and reinstall the middle screws.
Installation Instructions - Dual Integrated Installation STEP 6 CONNECTING WATER SUPPLY STEP 6 CONNECTING WATER SUPPLY Ŷ Remove strain relief screw to allow for enough slack to make a proper water connection. (Screw must be replaced in the next step.) WARNING ELECTRIC SHOCK HAZARD Attach tubing clamp using existing hole only. DO NOT drill into the refrigerator. Strain Relief Screw RISQUE DE DÉCHARGE ÉLECTRIQUE Fixez le collier de serrage dans le trou présent seulement.
Installation Instructions - Dual Integrated Installation STEP 7 INSERTING/SECURING INTO CABINET SURROUND WARNING STEP 7 INSERTING/SECURING INTO CABINET SURROUND Electrical Shock Hazard. WARNING To reduce the risk of electrical shock, be careful during the remaining installation steps not to touch wiring or electrical components inside the compressor compartment while the appliance is plugged in and the front access cover is not in place. AVERTISSEMENT Tip Over Hazard.
Installation Instructions - Dual Integrated Installation STEP 7 INSERTING/SECURING INTO CABINET SURROUND (Cont.) STEP 8 LEVEL UNIT All models have 4-point leveling. The front is supported by leveling legs; the rear is supported by adjustable wheels. Both are accessible from the front of the unit. Ŷ To level the back of the unit, turn the 7/16” hex nut located above the front leveling legs. Turn clockwise to raise or counterclockwise to lower the unit.
Installation Instructions - Dual Integrated Installation STEP 9 FINAL EXTERNAL UNIT PREPARATION (Cont.) STEP 9 FINAL EXTERNAL UNIT PREPARATION FOR FLUSH INSTALLATION: Make sure front surface of the door is 7/8” behind front face of surrounding cabinets BEFORE securing brackets to the surrounding Compartment Door cabinetry. 1/4” Hex Screws Filter Ŷ Open the doors to the units. Locate Mounting Hook ¿OWHU DQG ¿OWHU removal tool. Filter should be as shown.
Installation Instructions - Dual Integrated Installation STEP 9 FINAL EXTERNAL UNIT PREPARATION (Cont.) STEP 11 INTERNAL UNIT PREPARATION Ŷ Install front mullion and access cover trims between the 2 units. Open the doors and the flexible dart in the area between units. Ŷ Remove all tape, cardboard, and foam from each unit (foam shipping supports may be located behind the left and right sides of each of the glass pan fronts on Refrigerator models). Ŷ Remove boxed door bins from shelves.
Installation Instructions - Dual Integrated Installation STEP 12 START ICEMAKER (freezer models) STEP 12 START ICEMAKER (freezer models) When the freezer has been connected to the water supply, set the power switch to ON. Throw away the first full bucket of ice to allow the water line to clear. Be sure nothing interferes with the sweep of the feeler arm.
Installation Instructions - Dual Integrated Installation STEP 13 INSTALL AUTOFILL PITCHER ASSEMBLY (Some Refrigerator Models) Ŷ Locate the AutoFill pitcher cover on the left side of the refrigerator’s interior. Remove T20 Torx screw holding the cover in place towards the rear of the cover. Retain this screw for attachment of AutoFill assembly.
Instructions for Retro-Fit Installation Existing construction installation with 24” deep openings that are 35-1/2”, 36”, 41-1/2”, 47-1/2” or 71-1/2” wide 30 31-1000600 Rev.
Design Guide - Dual Retro-Fit Installation DUAL RETRO-FIT INSTALLATION SPACE Dimensions in parentheses are in centimeters. 24" (61.0) Enclosure Width 6" (15.2) Electric Location 6" (15.2) Finished Return E 5" (12.7) *83 1/2" min. *84 1/2" max. 75" (190.5) )URP ÀRRU to bottom of electrical area (212.1 – 214.6) *Trim will overlap additional 5/8" 5" (12.7) 5" 3 1/2" (12.7) (8.9) WATER W Side View Front View Enclosure Width Electric Location 35 1/2" (90.2) 15" (38.1) 36" (91.4) 15" (38.
Installation Instructions - Dual Retro-Fit Installation REFRIGERATOR/FREEZER LOCATION GROUNDING THE UNIT Ŷ Do not install the refrigerator/freezer where the temperature will go below 55°F (13°C). It will not run often enough to maintain proper temperatures. Ŷ Do not install the refrigerator/freezer where temperatures will go above 100°F (37°C). It will not perform properly. Ŷ Do not install the refrigerator/freezer in a location exposed to water (rain, etc.) or direct sunlight.
Installation Instructions - Dual Retro-Fit Installation KIT ZKUN PARTS SUPPLIED: STEP 1 REMOVE PACKAGING Adhesive Heater Transformer Front Mullion Trim Bracket Top Unification Bracket Bottom Front Unification Bracket 3 1/4” Hex Head 8-18 5/8” Long Screws 5 1/4” Hex Head 8-32 5/8” Long Screws 5 3/8” Hex Head 1/4-20 1/2” Long Screws 4 wire clips Ŷ Remove hardware kit from top drawer.
Installation Instructions - Dual Retro-Fit Installation STEP 2 INSTALL WATER LINE (Cont.) STEP 2 INSTALL WATER LINE WARNING Connect to potable water supply NOTE: Saddle type shut-off valves are included in many water supply kits. Before purchasing, make sure a saddle type valve complies with your local plumbing codes. only. A cold water supply is required for automatic icemaker operation. The water pressure must be between 40 and 120 psi (275-827 kilopascals).
Installation Instructions - Dual Retro-Fit Installation STEP 3 PREPARING UNIT FOR INSTALLATION STEP 3 PREPARING UNIT FOR INSTALLATION Ŷ Unpack the heater Unification Kit (ZKUN) and make sure all of the components on the list are included. NOTE: Ensure the heater connector cord is toward the top of the unit when installed. Ŷ Place the right hand unit in front of the installation opening in a way that the unit is in front of the intended installed location.
Installation Instructions - Dual Retro-Fit Installation STEP 4 INSTALL ANTI-TIP BRACKET WARNING Ŷ Measure and mark from the RH side of the opening per the table above depending on the size of the RH unit you are installing. Tip Over Hazard. These appliances are top heavy, especially with any doors open, and must be secured to prevent tipping forward which could result in death or serious injury. Read and follow the entire installation instructions for securing the appliance with the anti-tip system.
Installation Instructions - Dual Retro-Fit Installation STEP 5 JOINING DUAL INSTALLED UNITS BOTTOM BACK UNIFICATION TOP UNIFICATION Ŷ Loosen the two bottom screws of rear access covers of both units and remove the top screws. Ŷ /RRVHQ WKH PLGGOH WZR VFUHZV UHPRYH WKH WZR UHDU screws. Ŷ Hang the unification bracket to the bottom screws and reassemble the screws at the top Ŷ $VVHPEOH WKH EUDFNHW WR WKH PLGGOH VFUHZV DQG reassemble the rear screws. Ŷ Tighten screws to tie units together.
Installation Instructions - Dual Retro-Fit Installation STEP 5 JOINING DUAL INSTALLED UNITS (Cont.) CHANGE POWER CORD Longer power cords are required for retro fit installation. Power cords are included in 42” ZKR42N and 48” ZKR48N. Replace power cords on both units. Both units can be plugged into the same electrical supply receptacle. Remove existing short power cord with string assembly: Ŷ Remove 1/4” hex screws attaching rear access cover. 1.
Installation Instructions - Dual Retro-Fit Installation STEP 5 JOINING DUAL INSTALLED UNITS (Cont.) STEP 6 CONNECTING WATER SUPPLY CASE TRIM INSTALLATION WARNING Connect to potable water supply Ŷ Fit the top trim and side trim rails together by sliding the exposed edges of the corner trim into the right and left trim kit side rails. Align and drive the two number 10-24 Phillips head screws into the screw bosses in the side rails to ensure the top trim is snugly fit to the side rails. only.
Installation Instructions - Dual Retro-Fit Installation STEP 6 CONNECTING WATER SUPPLY STEP 7 INSERTING/SECURING INTO CABINET SURROUND Ŷ Locate and bring the tubing to the front of the cabinet. Ŷ Turn the water on to flush debris from the line. Run about a quart of water through the tubing into a bucket, then shut off the water. Ŷ Remove strain relief screw to allow for enough slack to make a proper water connection. (Screw must be replaced in the next step.) Ŷ Plug both units to the outlet in the wall.
Installation Instructions - Dual Retro-Fit Installation STEP 7 INSERTING/SECURING INTO CABINET SURROUND STEP 7 INSERTING/SECURING INTO CABINET SURROUND Ŷ Slowly walk both units into opening making sure not to touch the cabinetry on the sides and top to prevent damage. The back side of the top and side retro trims should be touching the cabinet surround when the units are pushed back. Ŷ Replace the waterline strain relief screw.
Installation Instructions - Dual Retro-Fit Installation STEP 9 FINAL EXTERNAL UNIT PREPARATION (Cont.) STEP 8 LEVEL UNIT All models have 4-point leveling. The front is supported by leveling legs; the rear is supported by adjustable wheels. Both are accessible from the front of the unit. Ŷ To level the back of the unit, turn the 7/16” hex nut located above the front leveling legs. Turn clockwise to raise or counterclockwise to lower the unit.
Installation Instructions - Dual Retro-Fit Installation STEP 9 FINAL EXTERNAL UNIT PREPARATION (Cont.) Ŷ For proper case placement after leveling, the back side of the top and side retro trims should be flush with the cabinet surround on all sides. Refrigerator or Freezer Ŷ Put the access cover back onto the unit and secure with two 1/4” hex head screws.
Installation Instructions - Dual Retro-Fit Installation STEP 12 START ICEMAKER (freezer models) STEP 10 TOE KICK INSTALLATION Ŷ Insert Toe Kick into the slot in the Front Access Cover by rotating it toward you. Ŷ Push the bottom portion of the Toe Kick towards the product and slide into place. A newly-installed freezer may take 12–24 hours to begin making ice.
Installation Instructions - Dual Retro-Fit Installation STEP 13 INSTALL AUTOFILL PITCHER ASSEMBLY (Some Refrigerator Models) Ŷ Locate the AutoFill pitcher cover on the left side of the refrigerator’s interior. Remove T20 Torx screw holding the cover in place towards the rear of the cover. Retain this screw for attachment of AutoFill assembly.
Instructions for Single Integrated Installation New construction installation with 25” deep openings 46 31-1000600 Rev.
Design Guide - Single Integrated Installation SINGLE INTEGRATED INSTALLATION SPACE Dimensions in parentheses are in centimeters. 25" (63.5) Enclosure Width (See Chart) 6" (15.2) Finished Return 84" (213.4) C A D B ELECTRIC WATER 2 1/2" (6.4) PRODUCT ENCLOSURE WIDTH A B C D 17 13/16 4 1/8 3 1/2 7 1/2 2 45.2 10.5 8.9 19.1 5.1 23 13/16 4 3/8 5 9 1/2 4 60.5 11.1 12.7 24.1 10.2 29 13/16 4 3/8 5 9 1/2 4 75.7 11.1 12.7 24.1 10.2 35 13/16 8 9 18 9 91.0 20.3 22.
Installation Instructions - Single Integrated Installation REFRIGERATOR/FREEZER LOCATION GROUNDING THE UNIT Ŷ Do not install the refrigerator/freezer where the temperature will go below 55°F (13°C). It will not run often enough to maintain proper temperatures. Ŷ Do not install the refrigerator/freezer where temperatures will go above 100°F (37°C). It will not perform properly. Ŷ Do not install the refrigerator/freezer in a location exposed to water (rain, etc.) or direct sunlight.
Installation Instructions - Single Integrated Installation HARDWARE SUPPLIED (per unit) • • • • • • • • • • • • • • • • • • • STEP 1 REMOVE PACKAGING Water Filter Bypass Plug (if equipped) Air filter (if equipped) Anti-Tip bracket (qty 2 for 36”) 3 Lag screws (qty 6 for 36”) 3 Tapcon screws (qty 6 for 36”) 3 Toggles with bolts (qty 6 for 36”) Panel installation templates 2 Door trims 2 Door panel brackets Set screws #6 Phillips head wood screws Door Bracket Cover Top T30 screws 1 Hinge limiter pin Center
Installation Instructions - Single Integrated Installation STEP 1 REMOVE PACKAGING (Cont.) Ŷ Remove front access cover from unit by removing two 1/4” hex head screws (some models have access cover in a box on the left side of the cabinet). Place the cover and screws to the side for future installation. Ŷ Remove three 3/8” drive screws and two 7/16” drive screws from each side of the unit to release it from the shipping skid.
Installation Instructions - Single Integrated Installation STEP 3 PREPARING UNIT FOR INSTALLATION STEP 4 INSTALL ANTI-TIP BRACKET Ŷ Measure and mark from the right side of the opening per the table depending on the size of the unit you are installing. Ŷ Place the unit in front of the installation opening in a way that the unit is in front of the intended installed location. Ŷ Mount the anti-tip bracket centered about the mark and flush to the floor as shown.
Installation Instructions - Single Integrated Installation STEP 5 CONNECT WATER SUPPLY STEP 5 CONNECT WATER SUPPLY WARNING Connect to potable water supply only. A cold water supply is required for automatic icemaker operation. The water pressure must be between 40 and 120 psi (275-827 kilopascals). House Water Supply WARNING ELECTRIC SHOCK HAZARD Attach tubing clamp using existing hole only. DO NOT drill into the refrigerator.
Installation Instructions - Single Integrated Installation STEP 6 INSERTING/SECURING INTO CABINET SURROUND STEP 6 INSERTING/SECURING INTO CABINET SURROUND Ŷ Plug unit into the outlet in the wall. Ŷ Slowly walk the unit into opening making sure not to touch the cabinetry on the sides and top to prevent damage. Door face should be 7/8” behind the front face of surrounding cabinets on either a stainless or custom panel installation. WARNING Electrical Shock Hazard.
Installation Instructions - Single Integrated Installation STEP 7 LEVEL UNIT STEP 6 INSERTING/SECURING INTO CABINET SURROUND NOTICE: The rear leveling wheels and front leveling legs are limited to a maximum height adjustment of 1”. If the installation requires more than 84” height, the installer should elevate the unit on a sheet of plywood or runners. Cabinetry trim could also be added across the top of the opening to shorten the opening.
Installation Instructions - Single Integrated Installation STEP 8 FINAL EXTERNAL UNIT PREPARATION (Cont.) STEP 8 FINAL EXTERNAL UNIT PREPARATION (Cont.) Ŷ Make sure lights are on inside the unit. If they are not on, check to make sure the master switch is on by removing the front enclosure which is secured with six 1/4” Hex screws. Ŷ Put the access cover back onto the unit and secure with two 1/4” hex head screws. 1/4” Hex Screws Access Cover Ŷ Switch on the master switch if not on.
Installation Instructions - Single Integrated Installation STEP 11 START ICEMAKER (freezer models) CAUTION To minimize the risk of personal injury, avoid contact with the moving parts of the ejector mechanism, or with the heating element that releases the cubes. Do not place fingers or hands on the automatic ice making mechanism while the appliance is plugged in.
Installation Instructions - Single Integrated Installation STEP 12 INSTALL AUTOFILL PITCHER ASSEMBLY (Some Refrigerator Models) Ŷ Locate the AutoFill pitcher cover on the left side of the refrigerator’s interior. Remove the one T20 Torx screw holding the cover in place towards the rear of the cover. Retain this screw for attachment of AutoFill assembly.
Stainless Steel Door Panel Installation This step can be done for all installation types. 58 31-1000600 Rev.
Installation Instructions - Stainless Door Panel Stainless Steel Door Panel Kits are available with either Euro handles or Pro handles.
Installation Instructions - Stainless Door Panel STEP 2 ADJUST STAINLESS PANEL (Cont.) Ŷ Follow the next steps for set screw installation. Ŷ For flush mounting, inspect the gap between the panel and cabinetry at the handle side. ¿ If the vertical gap between the cabinetry is smaller at the top than the bottom, insert and drive the vertical screw on the top bracket near the hinge side until the gap is equal along the entire vertical section. (You may need to slide the panel to realign the side gap to 1/8”.
Installation Instructions - Stainless Door Panel STEP 3 IF DOORS WERE REVERSED COMPLETE THE FOLLOWING STEPS Ŷ Top cover assembly shipped in box on side of product. Remove screws and nuts to remove rectangular cover. Retain parts to build new top assembly. Ŷ Mount rectangular cover to bottom cover (removed during door reversal) utilizing the screws and nuts that were removed from top assembly. Be sure to align the edges during assembly.
Installation Instructions - Stainless Door Panel STEP 5 INSTALL DOOR TRIMS There are 2 door trims to install. One for the handle side and one for the hinge side. The long trim is for the handle side and the shorter trim is for the hinge side. Install the handle side trim first. Ŷ Without touching the exposed tape to the side of the door, align the top of the trim with the top of the door panel. (tape backer should be sticking out when aligning the trim).
Custom Overlay Door Panel Installation This step can be done for all installation types. 31-1000600 Rev.
Design Guide - Custom Overlay Door Panel CUSTOM HANDLE DESIGN GUIDE Custom handles must be used for flush installation. For custom handle installation, counter-bore holes in rear of decorative panels must ensure 1/2” (1.27cm) material thickness remains for handle support. NOTE: The counterbore must not exceed 1” (2.54cm) in diameter. 1/4" (0.64cm) Minimum distance from panel side edge to handle center should be 1-1/2” (3.81 cm) as shown. 1-1/2” 1/2" (1.27cm) 3/4" (1.
Installation Instructions - Custom Overlay Door Panel STEP 1 OVERLAY PANEL PREP Ŷ Verify overall panel dimensions match supplied recommendations based on model and inspect for any initial damage. Ŷ Lay the template on the BACK of the panel, making sure to align the top edge (black line) of the template to the top edge of the panel. The template side edges should be aligned with the handle side of the panel. Secure the template to the panel so it does not move when marking hole locations.
Installation Instructions - Custom Overlay Door Panel STEP 3 ADJUST OVERLAY PANEL (Cont.) STEP 2 INSTALL OVERLAY PANEL Ŷ Remove bottom hinge cover and retain the 4 T30 Torx screws for later installation. Ŷ Follow the next steps for set screw installation. Ŷ For flush mounting, inspect the gap between the panel and cabinetry at the handle side.
Installation Instructions - Custom Overlay Door Panel STEP 3 ADJUST OVERLAY PANEL (Cont.) After the panel has been adjusted to the desired position, secure the panel by first driving and tightening the vertical screws at the bottom of the door brackets and then drive and tighten the remaining horizontal screws. ALL 12 SET SCREWS should be driven and firmly tightened in order to properly secure the panel.
Installation Instructions - Custom Overlay Door Panel STEP 5 INSTALL HINGE COVERS STEP 6 INSTALL DOOR TRIMS Ŷ Replace the top and bottom hinge covers using 4-T30 screws per cover. There are 2 door trims to install. One for the handle side and one for the hinge side. The long trim is for the handle side and the shorter trim is for the hinge side. Install the handle side trim first.
Installation Instructions - Custom Overlay Door Panel STEP 6 INSTALL DOOR TRIMS (cont.) Ŷ Without touching the exposed tape to the side of the door, align the top of the trim with the top of the door panel. (tape backer should be sticking out when aligning the trim). Ŷ Once the trim is location (aligned to the top the door, hinge covers, tight to the door and door panel), then push on the exposed tape area to secure.
Notes 70 31-1000600 Rev.
Notes 31-1000600 Rev.
NOTE: While performing installations described in this book, safety glasses or goggles should be worn. NOTE: Product improvement is a continuing endeavor at Monogram. Therefore, materials, appearance and specifications are subject to change without notice. 31-100600 Rev.
