Spec Sheet

For questions about your
appliance, please call 1-800-626-2000.
Product Specication Created 10/19PAGE 8 OF 17
STANDARD INSTALLATION
HELPFUL TIPS
A
In a side-by-side installation of a
left-and-right-hand door swing
product, 1" clearance between the
units is required.
Order a ZKBFN720NII unification kit
for an integrated appearance on 2 custom
panel models installed side-by-side.
B
In a side-by-side installation with same
door swing, allow 2" minimum
clearance between the products to
prevent the door swing interference.
Allow 15" minimum to a wall to achieve
full drawer extension and pan removal.
Additional clearances are required
when using custom panels and handles.
NOTE: ZKBSN720NSS and
ZKBFN720NII unification kits will not
fit this installation.
C
In a side-by-side installation with
right and left door hinges together,
allow 5” minimum clearance between
the two products to prevent one
door from striking the other.
Additional clearances required when
using custom panels and handles.
NOTE: ZKBSN720NSS and
ZKBFN720NII unification kits will not
fit this installation.
DUAL PRODUCT CLEARANCES
71 1/2" (181.6)
Finished Width
24" (61.0)
Min. Cutout Depth
24 3/16" (61.4)
2 5/16"
(5.9)
5 1/2"
(13.9)
9"
(22.9)
83 1/2" min
84 1/2" max
(212.1-214.6)
Finished Opening
3 1/2"
(8.9)
ZIF360NXLH_ZIF360NXRH _ZIFP360NXLH_ZIFP360NXRH_ ZIFS360NXLH_ZIFS360NXRH
ZIR360NXLH_ZIR360NXRH_ZIRP360NXLH_ZIRP360NXRH_ZIRS360NXLH_ZIRS360NXRH
W
FRONT VIEW
ELEC.
5 1/2"
(13.9)
9"
(22.9)
3 1/2"
(8.9)
23 1/8" (58.7) min
To wall
23 1/8" (58.7) min
To wall
5" (12.7) min
23 1/8"
(58.7) min
To wall
1"
(2.5)
2" min
(5.1)
130˚
Door swing
130˚
Door swing
75 1/2"
(191.8 )
From floor
to bottom
of electrical
area
ELEC.
SIDE VIEW
5"
(12.7)
5"
(12.7)
5"
(12.7)
5"
(12.7)
WATER
3 1/2"
(9.0)
WATER
3 1/2"
(9.0)
A B
C
STANDARD 3/4" OVERLAY PANEL DIMENSIONS DUAL INSTALLATION
Grille Panel
Door
Panel
D
A
Door
Panel
B
C
D
3/4" Overlay Panels: For 3/4" thick
custom panels ordered from your
cabinet maker. e decorative panels
slide into the trim. e overlay panel
must be secured to a 1/4"-thick backer
panel which slides into the trim. A spacer
panel 0.10" thick must be placed between
the overlay and backer panels.
Center each panel over the other.
Assemble the panels with glue and
screws. Screws must be countersunk
into the backer panel.
NOTE: Left-to-right offset is not
always equal to top-to-bottom offset.
Maximum total panel weight:
• Door panel – 67 lbs.
• Grille panel – 25 lbs.
Order a ZKBFN720NII unification kit
for an integrated appearance on
2 custom panel models installed
side-by-side.
Door Handles:
Door handles are not provided. Custom
handles supplied by your cabinet maker
may be used. An optional visor handle
can be ordered as kit ZKLN.
PANEL ASSEMBLY
CROSS SECTION
Door
1/4" Backer Panel
.10" Spacer Panel
Optional ZKLN
kit handle
Trim
3/4" Overlay Panel
.25" + .10" + .75" = 1.10" Total Panel Thickness
PANEL DIMENSIONS
A B C D
1/4" Backer Panel 69 7/8" 8 7/8" 69 5/16" 33 7/8"
.10" Spacer Panel 68 1/2" 7 5/8" 67 15/16" 32 1/2"
3/4" Overlay Panel 70 1/8" 9" 69 9/16" 34 1/8"