Specifications

STANDARD INSTALLATION
ANTI-TIP BRACKET
ZISS360DKSSMONOGRAM 36" BUILT-IN SIDE-BY-SIDE REFRIGERATOR
FRONT VIEW SIDE VIEW
W
24" (61.0)
2"
(5.1)
4"
(10.2)
7/16" (1.1)
Trim overlap
3 1/2"
(8.9)
E
WATER
35 1/2" (90.2)
12" (30.5)
*83 1/2" min
*84 1/2" max
(212.1-214.6)
*Trim will overlap
additional 7/16"
3 1/2"
(8.9)
75"
(190.5 )
From floor
to bottom
of electrical
area
6"
(15.2)
5"
(12.7)
5"
(12.7)
5"
(12.7)
ZISS360DXSS
SIDE VIEW INSTALLED
WITH WOODEN WALL STUDS
AND NO SOFFIT
SIDE VIEW INSTALLED
UNDER SOFFIT
SOFFIT
*84"
(213.4)
*Or installation
height from floor
2" x 4"
Cut to 35" Length
Screws mounted
into vertical wall
studs
FRONT VIEW INSTALLED
WITH METAL WALL STUDS
AND NO SOFFIT
Top Case Trim
3/4"
Min.
Side View Top
Case Trim
Install Screws
Through Trim and Into
3/4" Min. Wood Brace
FRONT VIEW SIDE VIEW
W
24" (61.0)
2"
(5.1)
4"
(10.2)
7/16" (1.1)
Trim overlap
3 1/2"
(8.9)
E
WATER
35 1/2" (90.2)
12" (30.5)
*83 1/2" min
*84 1/2" max
(212.1-214.6)
*Trim will overlap
additional 7/16"
3 1/2"
(8.9)
75"
(190.5 )
From floor
to bottom
of electrical
area
6"
(15.2)
5"
(12.7)
5"
(12.7)
5"
(12.7)
ZISS360DXSS
SIDE VIEW INSTALLED
WITH WOODEN WALL STUDS
AND NO SOFFIT
SIDE VIEW INSTALLED
UNDER SOFFIT
SOFFIT
*84"
(213.4)
*Or installation
height from floor
2" x 4"
Cut to 35" Length
Screws mounted
into vertical wall
studs
FRONT VIEW INSTALLED
WITH METAL WALL STUDS
AND NO SOFFIT
Top Case Trim
3/4"
Min.
Side View Top
Case Trim
Install Screws
Through Trim and Into
3/4" Min. Wood Brace
A
B
D
C
E
The refrigerator will project forward, slightly beyond adjacent cabinetry.
A
Mounting the junction box
in this location will also
allow for front accessibility
through access panel.
B
Water supply area.
WARNING:
The refrigerator is top heavy
and must be secured to
prevent the possibility of
tipping forward. Failure to
do so may result in death or
serious injury.
The information below is for
cabinet design only. When
installing the anti-tip system
you must use the product
installation instructions.
Determine your installation
construction and required anti-
tip configuration:
C
Installed Under Sot
After installing unit into
installation opening, raise
grille panel and screw metal
case sides to adjacent cabinet.
When installed under a sot,
the sot cannot exceed 24"
deep. The top case trim
overlaps the bottom of the
sot.
D
Wooden Wall Studs and No
Sot
• Cut a 2" x 4" block and
secure to brackets provided.
• Secure brackets to back wall
of opening at 84" or your
installation height from the
floor.
E
Metal Wall Studs and No
Sot
This method requires securely
fastened cabinets on both
sides and a 3/4" minimum
wood brace above unit, with
it’s front surface 24" from back
wall.
• After installing unit into
opening, raise grille panel and
attach metal case top trim to
3/4" minimum wood brace.
• The brace spanning the
enclosure must be securely
fastened to cabinets on both
sides.
See Installation Instructions for
detailed instructions.
NOTES
Product Specification Revised 1/18