Quick Specifications
For questions about your
appliance, please call 1-800-626-2000.
Product Specication Created 10/19
HELPFUL TIPS
PAGE 3 OF 4
FRONT VIEW SIDE VIEW
W
24" (61.0)
2 1/4"
(5.7)
4 3/8"
(11.1)
7/16"
(1.1)
Trim overlap
3 1/2"
(8.9)
E
WATER
41 1/2" (105.4)
18" (45.7)
*83 1/2" min
*84 1/2" max
(212.1-214.6)
*Trim will overlap
additional 7/16"
3 1/2"
(8.9)
75"
(190.5 )
From floor
to bottom
of electrical
area
6"
(15.2)
5"
(12.7)
5"
(12.7)
5"
(12.7)
ZISS420NXSS
SIDE VIEW INSTALLED
WITH WOODEN WALL STUDS
AND NO SOFFIT
SIDE VIEW INSTALLED
UNDER SOFFIT
SOFFIT
*84"
(213.4)
*Or installation
height from floor
2" x 4"
Cut to 35" Length
Screws mounted
into vertical wall
studs
FRONT VIEW INSTALLED
WITH METAL WALL STUDS
AND NO SOFFIT
Top Case Trim
3/4"
Min.
Side View Top
Case Trim
Install Screws
Through Trim and Into
3/4" Min. Wood Brace
A
B
D
E
C
e refrigerator will project forward, slightly beyond adjacent cabinetry.
A
Mounting the junction box in this location
will also allow for front accessibility through
access panel.
B
Water supply area.
WARNING:
e refrigerator is top heavy and must be
secured to prevent the possibility of tipping
forward. Failure to do so may result in death
or serious injury.
e information below is for cabinet design
only. When installing the anti-tip system you
must use the product installation instructions.
Determine your installation construction and
required anti-tip configuration:
C
Installed Under Soffit
After installing unit into installation opening,
raise grille panel and screw metal case sides to
adjacent cabinet. When installed under a soffit,
the soffit cannot exceed 24" deep. e top case
trim overlaps the bottom of the soffit.
D
Wooden Wall Studs and No Soffit
• Cut a 2" x 4" block and secure to
brackets provided.
• Secure brackets to back wall of opening
at 84" or your installation height
from the floor.
E
Metal Wall Studs and No Soffit
is method requires securely fastened
cabinets on both sides and a 3/4" minimum
wood brace above unit, with it’s front surface
24" from back wall.
• After installing unit into opening, raise
grille panel and attach metal case top trim
to 3/4" minimum wood brace.
• e brace spanning the enclosure must
be securely fastened to cabinets on
both sides.
See Installation Instructions for detailed
instructions.
STANDARD INSTALLATION
ANTI-TIP BRACKET
FRONT VIEW SIDE VIEW
W
24" (61.0)
2 1/4"
(5.7)
4 3/8"
(11.1)
7/16" (1.1)
Trim overlap
3 1/2"
(8.9)
E
WATER
41 1/2" (105.4)
18" (45.7)
*83 1/2" min
*84 1/2" max
(212.1-214.6)
*Trim will overlap
additional 7/16"
3 1/2"
(8.9)
75"
(190.5 )
From floor
to bottom
of electrical
area
6"
(15.2)
5"
(12.7)
5"
(12.7)
5"
(12.7)
ZISS420NXSS
SIDE VIEW INSTALLED
WITH WOODEN WALL STUDS
AND NO SOFFIT
SIDE VIEW INSTALLED
UNDER SOFFIT
SOFFIT
*84"
(213.4)
*Or installation
height from floor
2" x 4"
Cut to 35" Length
Screws mounted
into vertical wall
studs
FRONT VIEW INSTALLED
WITH METAL WALL STUDS
AND NO SOFFIT
Top Case Trim
3/4"
Min.
Side View Top
Case Trim
Install Screws
Through Trim and Into
3/4" Min. Wood Brace