Installation Instructions If you have questions, call 800.626.2000 or visit our website at: www.monogram.
Safety Information Skill Level – Installation of this refrigerator requires basic mechanical, carpentry and plumbing skills. Proper installation is the responsibility of the installer. Product failure due to improper installation is not covered under the GE Appliance Warranty. See the Owner’s Manual for warranty information. BEFORE YOU BEGIN Read these instructions completely and carefully. • IMPORTANT – Save these instructions for local inspector’s use. Observe all governing codes and ordinances.
Design Guide THE INSTALLATION SPACE DIMENSIONS AND CLEARANCES 36" Models 12" 42" Models 18" 48" Models 20" 35", 41", or 47" Case Width *Finished Width 84 1/2" max 83 1/2" min Finished Opening 6" Electrical Area 5" 5" *83-1/2" at Rear 75" From Floor to Bottom of Electrical Area 24" Water Supply 5" 25-3/8" Framed Models 25-3/4" Stainless Steel Models Case Depth * Shipping height. The refrigerator can be adjusted to fit into a cutout that is 83-1/2" min. to 84-1/2" max. *84" From height.
Design Guide Refrigerator Frameless Cabinets: The case trim overlaps cabinets at the top and sides. Therefore, frameless cabinets may require filler strips to prevent interfeence with cabinet door swing. The opening must allow for filler strips.
Design Guide Frameless Cabinets: The case trim overlaps cabinets at the top and sides. Therefore, frameless cabinets may require filler strips to prevent interference with cabinet door swing. The opening must allow for filler strips.
Design Guide CUSTOMIZATION BASICS: Framed Or Overlay Panels, Custom Handles and Accessory Kits Stainless Steel Wrapped Models 36" wide models - ZISS360N, ZISS360D 42" wide models - ZISS420N, ZISS420D 48" wide models - ZISS480N, ZISS480D Trimmed Models 36" wide models - ZIS360N, ZISB360D, ZISW360D 42" wide models - ZIS420N, ZISB420D, ZISW420D 48" wide models - ZIS480N, ZISB480D, ZISW480D Overlay panels You may also choose to install custom overlay panels from your cabinet manufacturer.
Design Guide 1/4" FRAMED PANEL DIMENSIONS 5/16" Trim Reveal Door If you choose to install framed panels, they must be cut to the dimensions shown. The panels will slide into the frame on the door and grille. 1/4" Panel Non-Dispenser Models If the custom panel is less than 1/4" thick and it fits loosely in the door frame it can be backed up with a piece of filler material or foam tape to improve the fit. IMPORTANT NOTE: Maximum total panel weight: • Fresh food door panel – 75 lbs.
Design Guide 3/4" OVERLAY PANEL DIMENSIONS Overlay Panel Door For a more custom appearance, overlay panels may be installed on trimmed models. The overlay panel must be secured to a 1/4" thick backer panel which slides into the trim. A spacer panel 0.10" thick must be placed between the overlay and backer panel. Assemble the panels with glue and screws. • Center the spacer panel on the backer panel, left to right and top to bottom. Secure the panels with glue.
Design Guide DISPENSER MODELS: RAISED OVERLAY PANEL DESIGN 1/4" Backer Panel .10" Spacer 3/4" Overlay Panel When a raised panel design is to be used, a custom wide middle rail is required to accept the dispenser trim. • The middle rail must be wide enough to allow for the dispenser trim to overlap the opening. • The middle rail must be 1.100" total thickness to accept the dispenser trim.
Design Guide 24" SIDE PANELS Side panels must be used whenever the sides of the refrigerator will be exposed. The 1/4" side panels will slip into the side case trim. Secure the panels to the refrigerator *84" with stick-on hook and loop fastener strips. Order the side panels from the cabinet manufacturer. • Cut a notch in the top front corner as shown to allow clearance for corner keys in the front side trim.
Installation Instructions • Remove the four 7/16" bolts securing the straps to the skid. STEP 1 REMOVE PACKAGING CAUTION: Refrigerator is much heavier at the CAUTION: DO NOT ATTEMPT TO ROLL UNIT OFF SKID. top than at the bottom – be careful when moving. When using a hand truck, handle from side only. Toekick PRUDENCE: Le réfrigérateur est beaucoup plus lourd en haut qu'en bas. Il faut être prudent lors des déplacements. Si un diable est utilisé, il faut soulever le réfrigérateur sur le côté seulement.
Installation Instructions STEP 2A INSTALLATION WITH HOUSEHOLD WATER FILTRATION SYSTEM STEP 4 INSTALL ANTI-TIP BRACKETS WARNING: ANTI-TIP PRECAUTIONS The refrigerator is top-heavy and must be secured to prevent the possibility of tipping forward. Skip this step if you do not have a household water filtration system If the water supply to the refrigerator is from any household water filtration system, the filter cartridge should be removed.
Installation Instructions STEP 6 ALTERNATE ANTI-TIP PROCEDURE STEP 5 LEVEL REFRIGERATOR All models have 4-point leveling. The front is supported by leveling legs, the rear is supported by adjustable wheels. Both are accessible from the front of the refrigerator. • To level the back of the refrigerator, turn the 7/16" hex nut located above the front wheels. Turn clockwise to raise or counterclockwise to lower the refrigerator. • For front leveling, use a 1-1/4" open-end wrench.
Installation Instructions STEP 7 SECURE REFRIGERATOR TO CABINETRY STEP 9 INSTALL GRILLE PANEL To insert framed or overlay panel into the grille: • Raise the grille panel to stop position. Whenever possible, perform this step for anti-tip security, or when anti-tip brackets cannot be used. The refrigerator must be secured to prevent tipping. • Raise the grille panel to access case trim. • Drill hole in trim and drive screw through the trim into adjacent cabinet.
Installation Instructions STEP 10 INSTALL 1/4” FRAMED PANELS Go to Step 9A for Overlay Panels Handle Trim Door Trim Refrigerator Door Supplied Handle Shown in 1/4" Panel Position Install door panels: • Open door to 90°. Remove the 6 Phillips head screws from the door handle. • Remove handle. Retain all screws. • Remove 6 screws holding trim, lift off trim. Retain screws. • Slide framed panel into the door trim.
Installation Instructions STEP 10A INSTALL OVERLAY PANELS Door Trim Handle Trim Refrigerator Door Move Forward For 3/4" Panel Supplied Handle Shown in Overlay Panel Position Install door panels: • Open door to 90°. Remove the 6 Phillips head screws from the door handle. • Remove handle. Retain all screws. • Remove 6 screws holding trim, lift off trim. Retain screws. • Slide overlay panel into the door trim. Dispenser Models Only: • The dispenser controls protrude beyond the face of the freezer door.
Installation Instructions STEP 10A (continued) STEP 10A (continued) Custom Handles • If you are using custom handles, the handle must be properly secured to the overlay panel before sliding the panel into the trim. • The cabinet manufacturer will supply the custom handle and hardware. • Discard the supplied handle. • Carefully place the aluminum cover trim into top end cap so that the recess is aligned with the cap. Use the top to bottom grooves along the handle side to align the cover trim accurately.
Installation Instructions STEP 11 INSTALL DISPENSER TRIM STEP 12 CONNECT WATER SUPPLY Skip this step is you are installing a stainless steel wrapped or a non-dispenser refrigerator. There are two dispenser trims shipped with your refrigerator. Select the appropriate trim for your application. Framed Panel Trim Refrigerator Water Supply Overlay Panel Trim House Water Supply • Locate and bring tubing to the front of the cabinet. • Turn the water on to flush debris from line.
Installation Instructions STEP 15 INSTALL TOEKICK STEP 13 CHECK POWER, CLOSE GRILLE PANEL • Locate the supplied toekick (shipped taped to the side of the refrigerator). Install with 2 screws provided, adjust to desired height and tighten screws. • A custom toekick can be installed to match or complement the surrounding cabinetry. Use the supplied toekick as a template to cut the shape. • Check to be sure the power cord is plugged into the receptacle.
NOTE: While performing installations described in this book, safety glasses or goggles should be worn. For Monogram® local service in your area, call 1.800.444.1845. NOTE: Product improvement is a continuing endeavor at General Electric. Therefore, materials, appearance and specifications are subject to change without notice. Pub. No. 49-60314 Dwg. No.