Installation Instructions Above the Cooktop Oven PSA9120, PSA9240, ZSA1202 BEFORE YOU BEGIN • • IMPORTANT – Save these instructions for local inspector’s use. IMPORTANT – Observe all governing codes and ordinances. • Note to Installer – Be sure to leave these instructions with the Consumer. Note to Consumer – Keep these instructions for future reference. • Skill level – Installation of this appliance requires basic mechanical and electrical skills.
Installation Instructions CONTENTS General information Important Safety Instructions .............................. 3 C Recirculating ........................................ 19–22 Attach Mounting Plate to Wall ........... 19 Preparation of Top Cabinet ............... 19 Electrical Requirements........................................ 3 Adapting Blower for Recirculation ........................... 20, 21 Hood Exhaust .................................................... 4, 5 Mount the Oven ..............
Installation Instructions IMPORTANT SAFETY INSTRUCTIONS A qualified electrician must perform a ground continuity check on the wall receptacle before beginning the installation to ensure that the outlet box is properly grounded. If not properly grounded, or if the wall receptacle does not meet electrical requirements noted (under ELECTRICAL REQUIREMENTS), a qualified electrician should be employed to correct any deficiencies. WARNING Risk of Electric Shock.
Installation Instructions HOOD EXHAUST NOTE: Read these next two pages only if you plan to vent your exhaust to the outside. If you plan to recirculate the air back into the room, proceed to page 6. OUTSIDE TOP EXHAUST (EXAMPLE ONLY) The following chart describes an example of one possible ductwork installation. EQUIVALENT LENGTH x NUMBER USED = EQUIVALENT LENGTH Roof Cap 24 Ft. x (1) = 24 Ft. 12 Ft. Straight Duct Ǝ 5RXQG 12 Ft. x (1) = 12 Ft. x (1) = 5 Ft. = 41 Ft.
Installation Instructions NOTE: If you need to install ducts, note that the total duct length of 31»4Ǝ [ Ǝ UHFWDQJXODU RU Ǝ GLDPHWHU URXQG GXFW should not exceed 140 equivalent feet. Outside ventilation requires a HOOD EXHAUST DUCT. Read the following carefully. NOTE: It is important that venting be installed using the most direct route and with as few elbows as possible. This ensures clear venting of exhaust and helps prevent blockages.
Installation Instructions DAMAGE – SHIPMENT/ INSTALLATION PARTS INCLUDED • If the unit is damaged in shipment, return the unit to the store in which it was bought for repair or replacement. • If the unit is damaged by the customer, repair or replacement is the responsibility of the customer. • If the unit is damaged by the installer (if other than the customer), repair or replacement must be made by arrangement between customer and installer.
Installation Instructions TOOLS YOU WILL NEED # 1 and #2 Phillips screwdriver Tin snips (for cutting damper, if required) Ruler or tape measure and straight edge Pencil Scissors (to cut template, if necessary) Carpenter square (optional) Electric drill with 3»16Ǝ 7»16Ǝ 1»2Ǝ DQG 5»8Ǝ GULOO ELWV Filler blocks or scrap wood pieces, if needed for top cabinet spacing (used on recessed bottom cabinet installations only) Gloves Saw (saber, hole or keyhole) Safety goggles Stud finder or Hammer (opti
1 Installation Instructions PLACEMENT OF THE MOUNTING PLATE A REMOVING THE OVEN FROM THE CARTON/REMOVING THE MOUNTING PLATE B FINDING THE WALL STUDS 1 Remove the box containing the installation instructions, filters, exhaust adaptor, damper and the small hardware bag. Do not remove the Styrofoam protecting the front of the oven. 2 Fold back all 4 carton flaps fully against carton sides. Then carefully roll the oven and carton over onto the top side. The oven should be resting in the Styrofoam.
Installation Instructions C DETERMINING WALL PLATE LOCATION UNDER YOUR CABINET Plate position – beneath flat bottom cabinet Mounting Plate Tabs Touching the Cabinet Bottom Plate position – beneath framed recessed cabinet bottom Mounting Plate Tabs Touching the Back Frame Ǝ WR &RRNWRS $W OHDVW Ǝ XS WR Ǝ Plate position – beneath recessed bottom cabinet with front overhang Mounting Plate with Tabs Below Cabinet Bottom the Same Distance as the Front Overhang Depth Your cabinets may have decorative
Installation Instructions D ALIGNING THE WALL PLATE Hole B Draw a Vertical Line on Wall from Center of Top Cabinet Hole A Hole D Hole C Area E CAUTION Wear gloves to avoid cutting fingers on sharp edges. 1 'UDZ D YHUWLFDO OLQH RQ WKH ZDOO DW WKH FHQWHU RI WKH Ǝ wide space. 2 Use the mounting plate as the template for the rear wall.
Installation Instructions INSTALLATION TYPES 2 This oven is designed for adaptation to the following 3 types of ventilation: A. Outside Top Exhaust (Vertical Duct) B. Outside Back Exhaust (Horizontal Duct) C. Recirculating (Non-Vented Ductless) A OUTSIDE TOP EXHAUST (VERTICAL DUCT) (Choose A, B or C) NOTE: This oven is shipped assembled for Outside Top Exhaust. Select the type of ventilation required for your installation and proceed to that section.
Installation Instructions A OUTSIDE TOP EXHAUST (Vertical Duct) INSTALLATION OVERVIEW A1. A2. A3. A4. A5. A6. Attach Mounting Plate to Wall Prepare Top Cabinet Install Adaptor Mount Oven Adjust Exhaust Adaptor Connect Ductwork Select P re A1 ATTACH THE MOUNTING PLATE TO THE WALL s s to En To use toggle bolts: B A te r o rn t Tu Mounting Plate Spacing for Toggles More Than Wall Thickness Toggle Wings Toggle Bolt Wall Bolt End C D Attach the plate to the wall using toggle bolts.
Installation Instructions A2 USE TOP CABINET TEMPLATE FOR PREPARATION OF TOP CABINET A4 MOUNT THE OVEN You need to drill holes for the top support screws, a hole large enough for the power cord to fit through, and a cutout large enough for the exhaust adaptor. CAUTION To avoid the risk of personal injury (back injury or other injuries due to excessive weight of the microwave oven) or property damage, you will need two people to install this microwave oven.
Installation Instructions A4 MOUNT THE OVEN (continued) A5 ADJUST THE EXHAUST ADAPTOR Open the top cabinet and adjust the exhaust adaptor to connect to the house duct. 3 Attach the oven to the top cabinet. Damper 4 Insert 3 self-aligning screws (1»4Ǝ [ ǫƎ) through outer top cabinet holes. Turn two full turns on each screw. Back of Oven Cover Plate to Select e r rn Tu Pr e s s t o En t A6 CONNECTING DUCTWORK 5 Tighten center screw completely.
Installation Instructions B OUTSIDE BACK EXHAUST (Horizontal Duct) INSTALLATION OVERVIEW B1. B2. B3. B4. B5. Prepare Rear Wall Attach Mounting Plate to Wall Prepare Top Cabinet Adjust Blower Mount the Oven Select P re B1 PREPARING THE REAR WALL FOR OUTSIDE BACK EXHAUST te r o rn t Tu s s to En B2 ATTACH THE MOUNTING PLATE TO THE WALL You need to cut an opening in the rear wall for outside exhaust. Attach the plate to the wall using toggle bolts.
Installation Instructions To use toggle bolts: Spacing for Toggles More Than Wall Thickness Mounting Plate Toggle Wings Toggle Bolt Wall Bolt End 3 Place the mounting plate against the wall and insert the toggle wings into the holes in the wall to mount the plate. NOTE: Before tightening toggle bolts and wood screw, make sure the tabs on the mounting plate touch the bottom of the cabinet when pushed flush against the wall and that the plate is properly centered under the cabinet.
Installation Instructions 5 Roll the blower unit 90° so that fan blade openings are facing out the back of the oven. 8 Replace the blower plate in the same position as before with the screws. Attach the cover on the blower plate (include one screw). After Rolling Before Rolling Cover Plate Blower Plate Screws Blower Plate Back of Oven Back of Oven Back of Oven 6 Locate the two “knockout” plates, on the rear oven panel, near the top of the oven.
Installation Instructions B5 MOUNT THE OVEN Cabinet Front Cabinet Bottom Shelf Filler Block Equivalent to Depth of Cabinet Recess CAUTION To avoid the risk of personal injury (back injury or other injuries due to excessive weight of the microwave oven) or property damage, you will need two people to install this microwave oven. IMPORTANT: Do not grip or use handle during installation. WARNING Risk of Electric Shock.
Installation Instructions C RECIRCULATING (Non-Vented Ductless) INSTALLATION OVERVIEW C1. C2. C3. C4. C5. Attach Mounting Plate to Wall Prepare Top Cabinet Adjust Blower Mount the Oven Install Charcoal Filter (not supplied) to Select te r Tu rn P ress to E n C1 ATTACH THE MOUNTING PLATE TO THE WALL 3 Place the mounting plate against the wall and insert the toggle wings into the holes in the wall to mount the plate.
Installation Instructions C3 ADAPTING BLOWER FOR RECIRCULATION 3 Carefully pull out the blower unit. The wires will extend far enough to allow you to adjust the blower unit. NOTE: The exhaust adaptor with damper is not needed for recirculating models. You may want to save them for possible future use. 1 Remove and save screws that hold blower plate to the oven. Blower Plate Screws Back of Oven Cover Plate 4 Roll the blower unit 90° so that fan blade openings are facing toward the front of the oven.
Installation Instructions C3 ADAPTING BLOWER FOR RECIRCULATION (continued) C4 MOUNT THE OVEN 5 Place the blower unit back into the opening. WARNING Risk of electric shock can cause injury or death. Do not pull or stretch the blower unit wiring. Make sure the wired are not pinched. CAUTION 6 Secure blower unit to oven with the 2 screws removed in Step 2. Insert the screw in bottom right screw hole on the back of the oven. 7 Reattach the cover plate on the back.
Installation Instructions C4 MOUNT THE OVEN (continued) 3 Insert a self-aligning screw through top-center cabinet hole. Temporarily secure the oven by turning the screw at least two full turns after the threads have engaged. (It will be completely tightened later.) Cabinet Front C5 INSTALLING THE CHARCOAL FILTER 1 Remove 2 screws on top of oven, just above the grille panel, using a Phillips screwdriver. 2 Open the door. 3 Remove the grille. Slide the grille to the left then pull out.
Installation Instructions BEFORE YOU USE YOUR OVEN 1 Make sure the oven has been installed according to instructions. 5 (continued) 240 V Models: The wall outlet receptacle recommended for this appliance is NEMA #14–30R and accepts the four-prong grounded plug of this appliance. NEMA 14–30R Wall Receptacle 2 Remove all packing material from the oven. 3 Install turntable and wheeled ring in cavity. 4 Replace house fuse or turn breaker back on. 5 Ensure proper ground exists before use.
Printed in China 24 31-7000138 Rev.
Instrucciones Horno para colocar encima de la estufa de instalación PSA9120, PSA9240, ZSA1202 ANTES DE EMPEZAR • • IMPORTANTE – Guarde estas instrucciones para el uso del inspector local. IMPORTANTE – Cumpla con todos los códigos y ordenanzas gubernamentales. • Nota para el instalador – Asegúrese de dejar estas instrucciones con el consumidor. • Nota para el consumidor – Guarde estas instrucciones para futura referencia.
Instrucciones de instalación CONTENIDO C Recirculación ....................................... 43–46 Información general Cómo adherir la placa de montaje a la pared ............................. 43 Instrucciones de seguridad importantes .......... 27 Preparación del gabinete superior......43 Requisitos eléctricos .......................................... 27 Cómo adaptar el calefactor para la recirculación..................... 44, 45 Campana de escape ......................................
Instrucciones de instalación INSTRUCCIONES DE SEGURIDAD IMPORTANTES Este producto requiere un tomacorriente eléctrico de tres patas conectado a tierra. El instalador debe llevar a cabo una inspección de continuidad a tierra en la caja eléctrica antes de comenzar la instalación para asegurar que la caja tomacorriente está conectada a tierra de manera apropiada.
Instrucciones de instalación CAMPANA DE ESCAPE NOTA: Lea las siguientes dos páginas solamente si planea ventilar el escape hacia el exterior. Si por el contrario planea recircular el aire de vuelta hacia el salón, continúe en la página 30. ESCAPE SUPERIOR EXTERNO (EJEMPLO SOLAMENTE) La siguiente tabla describe un ejemplo de una posible instalación de red de conductos.
Instrucciones de instalación NOTA: Si usted necesita instalar conductos, tenga pendiente que la longitud total del conducto rectangular de 31»4Ǝ [ Ǝ R HO FRQGXFWR UHGRQGR GH Ǝ GH GLiPHWUR no debe sobrepasar 140 pies equivalentes. La ventilación externa requiere un CONDUCTO DE CAMPANA DE ESCAPE. Lea lo siguiente cuidadosamente. NOTA: Es importante que la ventilación sea instalada usando la ruta más directa y con la menor cantidad de codos posible.
Instrucciones de instalación DAÑOS – ENVÍO / INSTALACIÓN • Si la unidad se daña durante el envío, devuelva la unidad al almacén donde la adquirió para su reparación o reemplazo. • Si el cliente daña la unidad, la reparación o el reemplazo es responsabilidad del cliente. • Si el instalador daña la unidad (si no es el cliente), la reparación o reemplazo se debe hacer por medio de un arreglo entre el cliente y el instalador.
Instrucciones de instalación HERRAMIENTAS QUE NECESITARÁ Destornilladores de estrella # 1 y # 2 Tijeras para cortar latón (para cortar el regulador de tiro, si es necesario) Regla recta y cinta métrica Lápiz Tijeras (para cortar la plantilla, si es necesario) Taladro eléctrico con brocas de 3»16Ǝ 7»16Ǝ 1»2Ǝ \ 5»8Ǝ Bloques de relleno o pedazos de madera, si son necesarios para rellenar el gabinete (usados solamente en la instalación de gabinetes apoyados) Guantes Sierra (de sable, agujero, o de o
Instrucciones de instalación 1 CÓMO COLOCAR EL PLATO DE MONTAJE A CÓMO REMOVER EL HORNO DEL EMBALAJE / CÓMO REMOVER EL PLATO DE MONTAJE B CÓMO ENCONTRAR LOS POSTES DE VIGA EN LA PARED 1 Remueva la caja que contiene las instrucciones de instalación, los filtros, el adaptador de escape, el regulador de tiro y la pequeña bolsa con los elementos de instalación. No remueva la espuma de poliestireno que protege el frente del horno. 2 Pliegue hacia atrás las alas de la caja.
Instrucciones de instalación C CÓMO DETERMINAR LA LOCALIZACIÓN DEL PLATO DE MONTAJE DEBAJO DE SU GABINETE Posición del plato – debajo de gabinetes de fondo plano Las orejillas del plato de montaje tocan el fondo del gabinete 3RU OR PHQRV Ǝ KDVWD Ǝ Posición del plato – debajo de gabinetes de fondo apoyado con frente saliente Plato de montaje con orejillas por debajo del fondo del gabinete a la misma distancia que la profundidad del saliente Posición del plato – debajo de gabinetes de fondo apoyado e
Instrucciones de instalación D CÓMO ALINEAR EL PLATO DE MONTAJE SOBRE LA PARED Trace una línea vertical en la pared a partir del centro del gabinete superior Agujero A Agujero C Agujero B Agujero D Area E PRECAUCIÓN Use guantes de protección para evitar cortaduras en sus dedos con los extremos filosos. 1 Trace una línea vertical en la pared en el centro GHO HVSDFLR GH Ǝ GH DQFKR 2 Use el plato de montaje como la plantilla para la pared posterior.
Instrucciones de instalación TIPOS DE INSTALACIÓN 2 Este horno está diseñado para adaptarse a los siguientes tres tipos de ventilación: A. Escape superior exterior (Conducto vertical) B. Escape posterior exterior (Conducto horizontal) C. Recirculación (Sin conducto de ventilación) A ESCAPE SUPERIOR EXTERIOR (CONDUCTO VERTICAL) (Escoja A, B o C) NOTA: Este horno es enviado ya ensamblado para un escape superior exterior.
Instrucciones de instalación A ESCAPE SUPERIOR EXTERIOR (Conducto vertical) PERSPECTIVA GENERAL DE LA INSTALACIÓN A1. Como adherir el plato de montaje a la pared A2. Prepare el gabinete superior A3. Instale el adaptador A4. Monte el horno A5. Ajuste el adaptador de escape A6. Conecte el conducto Select P re A1 CÓMO ADHERIR LA PLACA DE MONTAJE A LA PARED Alas de mariposa Tornillo de mariposa Pared D Pegue el plato a la pared usando los tornillos basculantes.
Instrucciones de instalación A2 USE LA PLANTILLA DEL GABINETE SUPERIOR PARA LA PREPARACIÓN DEL GABINETE SUPERIOR Deberá perforar agujeros para los tornillos de apoyo superiores, un agujero suficientemente grande para que el cable eléctrico quepa, y un recorte lo suficientemente grande como para que el adaptador de escape pueda ser introducido.
Instrucciones de instalación A4 CÓMO MONTAR EL HORNO (continuación) 3 Pegue el horno a la parte superior del gabinete. 4 Inserte 3 tornillos (1»4s [ ǫs) autoalineables a través de los agujeros exteriores superiores del horno. Gire dos vueltas completas en cada tornillo. A5 CÓMO AJUSTAR EL ADAPTADOR DE ESCAPE Abra el gabinete superior y ajuste el adaptador de escape para conectarlo al conducto de la casa.
Instrucciones de instalación B ESCAPE POSTERIOR EXTERNO (Conducto horizontal) PERSPECTIVA GENERAL DE LA INSTALACIÓN B1. Prepare la pared posterior B2. Pegue el plato de montaje a la pared B3. Prepare el gabinete superior B4. Ajuste el calefactor B5. Monte el horno Select P re B1 CÓMO PREPARAR LA PARED POSTERIOR PARA EL ESCAPE POSTERIOR EXTERIOR te r o rn t Tu s s to En B2 CÓMO ADHERIR EL PLATO DE MONTAJE A LA PARED Necesita cortar una abertura en la pared posterior para el escape exterior.
Instrucciones de instalación Para usar los tornillos basculantes: Espaciadores para los basculantes mayores que el ancho de la pared Plato de montaje Alas de mariposa 1 Remueva y guarde los tornillos que sostienen Tornillo de mariposa Pared B4 CÓMO ADAPTAR EL CALEFACTOR PARA EL ESCAPE POSTERIOR EXTERIOR el plato del calefactor en el horno. Deslice el plato del calefactor de abajo de su reborde de retención. Remueva y guarde los tornillos que sostienen el motor del calefactor en el horno.
Instrucciones de instalación 5 Ruede la unidad del calefactor 90º de forma tal que las aberturas de la paleta del ventilador estén orientadas hacia la parte posterior del horno. Antes de la rotación 8 Coloque el plato calefactor en la misma posición como estaba antes con los tornillos. Coloque la cubierta en la placa del soplador (incluya un tornillo).
Instrucciones de instalación B5 CÓMO MONTAR EL HORNO Frente del gabinete Estante del fondo del gabinete Bloque de relleno PRECAUCIÓN A fin de evitar el riesgo de lesión personal (lesión en la espalda u otras lesiones debido a peso excesivo del horno de microondas) o daños sobre el producto, deberá contar con la ayuda de dos personas para instalar este horno de microondas Equivalente a la profundidad del retroceso del gabinete Esta distancia NO puede superar las ´ SDUD DVHJXUDU una instalación adecuad
Instrucciones de instalación C RECIRCULACIÓN (Sin conducto de ventilación) PERSPECTIVA GENERAL DE LA INSTALACIÓN C1. Pegue el plato de montaje a la pared C2. Prepare el gabinete superior C3. Ajuste el calefactor C4. Monte el horno C5. Instale el filtro de carbonilla (No suministrado) to Select te r Tu rn P ress to E n C1 CÓMO ADHERIR LA PLACA DE MONTAJE A LA PARED 3 Coloque el plato de montaje contra la pared e inserte las alas de mariposa en los agujeros de la pared para montar el plato.
Instrucciones de instalación C3 CÓMO ADAPTAR EL CALEFACTOR PARA LA RECIRCULACIÓN 3 Cuidadosamente tire del calefactor. Los alambres se extenderán lo suficiente para permitirle que usted ajuste la unidad del calefactor. NOTA: El adaptador de escape con calefactor no es necesario para los modelos de recirculación. Quizás desee guardarlos para posibles usos futuros. 1 Remueva y guarde los tornillos que sostienen el plato del calefactor en el horno.
Instrucciones de instalación C3 CÓMO ADAPTAR EL CALEFACTOR PARA LA RECIRCULACIÓN (continuación) 5 C4 CÓMO MONTAR EL HORNO Coloque la unidad del calefactor de nuevo en la abertura. ADVERTENCIA Existe riesgo de descargas eléctricas que pueden ocasionar lesiones o la muerte. No empuje ni extienda el cableado de la unidad de ventilación. Asegúrese de que los cables no posean cortes.
Instrucciones de instalación C4 CÓMO MONTAR EL HORNO (continuación) 4 Inserte un tornillo de autoalineación a través del agujero central superior del gabinete. Asegure el horno temporalmente girando el tornillo por lo menos dos vueltas completas después de que las roscas hayan agarrado. (Luego quedarán totalmente apretadas).
Instrucciones de instalación ANTES DE COMENZAR A USAR SU HORNO 1 Cerciórese de que el horno ha sido instalado de acuerdo con las instrucciones. 5 (continued) Modelos de 240 V: El tomacorriente de pared recomendado para este aparato es NEMA #14– 30R y puede usarse con el enchufe de 4 clavijas con conexión a tierra de este aparato. Tomacorriente de pared NEMA 14–30R 2 Remueva todos los materiales de embalaje del horno. 3 Instale el aro rotatorio y con ruedas en la cavidad.
Printed in China Impreso en China 48 31-7000138 Rev.