Installation Instructions

ManualsBrandsMonogram ManualsAppliance AccessoriesUnified Grille Kit

ZUGPP2 and

ZUGSS2 Trim Kit

Stainless Steel

Unified Grille Panel

Installation

Instructions

Tools and materials Required:

• #1 and #2 Phillips screwdrivers

• Safety glasses

• Gloves to protect against sharp edges

Parts List:

A. Stainless steel unified grille panel

B. Foam spacer pads

C. 10 Black #8-32 x 3/8” screws

This kit provides for the installation of a stainless steel unified

grille panel. The panel will span the combined width

of a side-by-side installation.

Completion Time: Allow approximately 2 hours to install

this kit.

IMPORTANT: 2 People are required to install this kit.

Disconnect power before you begin.

THE INSTALLATION SPACE

• The installation space must be 71-1/2" wide.

• The water and electrical locations for each product

must be located as shown.

• A separate 115V, 60Hz., 15 or 20 amp power supply

is recommended for each product.

Note: Additional cutout width may be required when

side panels are used. Add side panel thickness to the

finished cutout to calculate rough-in width.

71-1/2" Finished Width

Wall View

Electrical

24-3/16"

Electrical

Area

24" Minimum

Cutout Depth

75-1/2" From

Floor to Bottom

of Electrical Area

84-1/2" max.

83-1/2" min.

Finished

Opening

3-1/2"

3-1/2" 3-1/2"

3-1/2"

3-1/2"3-1/2"3-1/2"

5" 5"

Cold Water

Supply

Cold Water

Supply

5-1/2"

2-5/16"

Summary of content (8 pages)

PAGE 1
Installation Instructions ZUGPP2 and ZUGSS2 Trim Kit Stainless Steel Unified Grille Panel This kit provides for the installation of a stainless steel unified grille panel. The panel will span the combined width of a side-by-side installation. Completion Time: Allow approximately 2 hours to install this kit. IMPORTANT: 2 People are required to install this kit. Disconnect power before you begin. THE INSTALLATION SPACE • The installation space must be 71-1/2" wide.
PAGE 2
STEP 1 INSTALL FOAM SPACER PADS (Bottom–Mount and All Refrigerator/All Freezer Models) CAUTION: Handle parts with care to avoid scratching. PRUDENCE : Manipulez les pièces soigneusement pour éviter de les rayer. Apply the supplied foam spacer pads (B) to the mating side of one product as shown.
PAGE 3
STEP 2 INSTALL ANTI-TIP BRACKET ALL REFRIGERATOR, ALL FREEZER “X” MODELS ONLY WARNING: ANTI-TIP PRECAUTIONS The unit is top-heavy and must be secured to prevent the possibility of tipping forward. ATTENTION : PRECAUTIONS CONTRE LES BASCULEMENTS L’appareil ménager est beaucoup plus lourd en haut et il faut le maintenir en place pour éviter la possibilité de son basculement vers l’avant.
PAGE 4
STEP 2 INSTALL ANTI-TIP BRACKET (cont.) ALL REFRIGERATOR, ALL FREEZER “X” MODELS ONLY Install Wall Toggles: The wall toggles and bolts can be ordered as Service Kit #WR49X10193. Wall toggles are installed in the drywall and metal studs for stability. Install the wall toggles as follows: • Drill 1/2" holes at the wall markings made in the holes at the ends of the wall bracket. • Hold the metal channel flat against the plastic straps and slide the channel through the hole.
PAGE 5
STEP 2 INSTALL ANTI-TIP BRACKET (cont.) ALL REFRIGERATOR, ALL FREEZER “X” MODELS ONLY Freezer Unit • Open the access door. • Using a 1/4" hex driver, remove the 2 screws at the bottom of the grille on the right. • Pull the bottom of the grille forward, down and out to remove. • Using a 1/4" hex driver, remove the screw on the left side of the grille. • The grille is aluminum and will bend easily. Gently pull forward on the left side of the grille to open for access.
PAGE 6
STEP 4 SECURE UNIT TO WALL ALL REFRIGERATOR, ALL FREEZER “X” MODELS ONLY • The “L” rods can be found in the upper left and right corners of the unit in the access compartment. Look through the access compartment to make sure the rods line up with the anti-tip bracket. • There are 2 washers and a hair pin cotter per rod. Remove the washers and hair pin cotter from the end of the rod. • Rotate and move the “L” rod into the slot in the anti-tip bracket tab.
PAGE 7
STEP 5 SECURE SIDE TRIM TO CABINETRY • Whenever possible, perform this additional step. • Raise the grille panels to access cabinet side trims. • Drill hole in trim and drive screw through the trim and into each adjacent cabinet. Drive Screws through Case Trim and Into Adjacent Cabinets STEP 6 REMOVE BOTH GRILLE PANEL FRAMES • Grasp grille panel at the center, lift up to stop position. • Remove 3 screws holding the grille panel frame to the hinge on each side. Lift grille panel off the hinges.
PAGE 8
NOTE: While performing installations described in this book, safety glasses or goggles should be worn. NOTE: Product improvement is a continuing endeavor at General Electric. Therefore, materials, appearance and specifications are subject to change without notice. NOTA: Mientras efectúa las instalaciones descriptas en este libro, deben utilizarse gafas o lentes de seguridad. NOTA: La mejora de los productos es un esfuerzo continuo para General Electric.