Installation Instructions 42"Island Vent Hood Model: ZV1050 Monogram°
Design Information BEFORE YOU BEGIN WARNING: Read TO REDUCE THE RISK OF HRE, ELECTRICAL SHOCK OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: A. Use tiffs unit only in the manner intended by the manufacturer. If you have any questions, contact the these instructions completely " IMPORTANT local inspector's and carefully. - S.vethese instructionsfor use. • IMPORTANT • • • • • • - Observe .ll governing codes and ordinances. Note to Installer - Be sure to leave these instructions with the Gonsumer.
Design Information CONTENTS Design Information Product Dimensions ......................................................... Duct Cover Accessories ................................................ Determine Installation Height ........................................ Advance Planning Tools and Materials Required .......................................... Power Supply .................................................................... Duct Fittings ..........................................................
Design Information DETERMINE INSTALLATION HEIGHT DUCT COVER ACCESSORIES Order the accessory at the same time as the vent hood and have on site before installation begins. Use this chart to accurately determine the need for a Duct Cover Accessory. InstallationHeights Actual L_ .... m ....
Advance Planning TOOLS AND MATERIALS REQUIRED POWER SUPPLY (not supplied) • Tapemeasure • Knife • Spirit level • Wire cutter • Wire stripper • Wire nuts • Electric drill and 5/32" bit • Phillips screwdriver • Flat blade screwdriver • Hammer • Pliers • Safety glasses • Tapeto mount template • Gloves to protect against sharp edges • 120V60Hz, 15 or 20 Amp, 2wire with ground, properly grounded branch circuit • Strain relief for junction cover • Plumb bob • Center punch IMPORTANT - Please read carefully.
Advance Plannin Total Duct Piece Equivalent Length* Dimensions Quantity Used Equivalent Length Round, Use this permissible chart to compute lengths for straight (per toot length) 3-1/4" x 12" straight (per toot length) 90 ° elboB 17 ft. 45 ° elb(m I 0 ft. 90 ° elbo_ 3-1/4" x 12" 43 ft. 45 ° elb{}_ 3-1/4" x 12" 26 ft. 90 3-1/4" ° fiat x elboB 12" 102 it. Q 3-1/4" x 12" transition 8" round to 2 It. _lt, to 8" round 3-1/4" x 12" transition 5 it.
Installation Instructions [STEP 1 ] CONSTRUCT CEILING SUPPORT Ceiling Plan the location Determine the exact Hood location of the vent hood. Centerline • Use a plumb bob to check location to be sure countertop/cooktop location below the hood will align exactly. • The hood should project forward 1-1/2" beyond the front edge of the cooking appliance. See illustration. • Observe the recommended space (30") between the cooking surface and bottom of hood. Front 31-1/2" i...................................
Installation Instructions [STEP 1 ] CONSTRUCT CEILING SUPPORT (cont.) EXAMPLE B | 16"Joist Spacing 11-1/4"InstallCross-Framing SymmetricallyAbout 2x4 Cross \ Framing \ Align Ductto Centerof Cooktop Cooktop Outline Front of Hood TopView--Ceiling Joists RunPerpendicularto Frontof Hood EXAMPLE C 2x4Cross Framing 11-1/4"Install Cross-Framing SymmetricallyAbout Duct/CooktopCenterline i 1 16"Joist Spacing Align Ductto Centerof Cooktop Front of Hood TopView--Ceiling Joists at Anglewith Frontof Hood
Installation Instructions 2x 4 Min. CrossFraming I STEP 11CONTINUED N ......... • Arrange cross flaming in the ceiling to suit the existing suuculre. See examples. - Secure each 2 x 4 block with at least four (4), #10 wood screws, 3" long (not supplied). Use 8 wood screws total for the two supports. '- d Ceiling'/ • The cross framing must be accurately aligned to assure correct positioning of the hood. • The cross framing must be level in all directions.
Installation Instructions ISTEP 21 REMOVE THE PACKAGING The vent hood is packed separately flom the decorative duct cover or accessory covers ZX1059SFSS or ZX10510SFSS. • Remove the flame, cover, parts box and packaging. • Remove junction box cover. • Install suain relief onto junction box coveL [STEP 3 CHECK INSTALLATION I,ocate the hardware hood and check accessory pack shipped HARDWARE with the contents.
Installation ISTEP 4 ] MOUNT Instructions TEMPLATE • Align the template with tile marks on tile ceiling and rope in place. - Be sure tile template is oriented correctly, with tile flont of tile hood. • Use a phnnb bob to be sure the mounting holes will provide parallel alignment with tile countertop below. • Center punch all hole locations. • Drill pilot holes in tile 4 screw locations. Use a 5/32" bit and drill approximately 1-1/2" deep. • Gut tile 8-1/4" duct opening and approx. 1" wire access hole.
Installation Instructions [STEP 6 SECURE WIRING • Route house pull a length approximately wiring through the ceiling to reach the hood junction 6" below the support. STEP 7 SIZE AND INSTALL DUCTWORK hole and box, : _/_ i, i Celing / Ceiling / , i i . HouseDuct.... _C, LeftSide View m Support_. Frames " "- :L[__ ! ""-' _'",Req Side View Support Frame \ \\ Duct Dim.A ired Duct Lenth \ }Tape DuctConnection ToHood ....
Installation Instructions I STEP 81 INSTALL DECORATIVE DUCT COVERS InstallScrewon EachSide \\\ Pretap 2 Screw Holes (One On Each Side) BottomDuctCover BottomDuct Cover ! o Top Duct Cover Stop _ Screw o=a \... Install Stop Screw in Hole A/ of Upper (Inner) Duct Cover • Pretap or drive decorative screw into the screw holes on the support frame. This will make screw installation easier. • Slide the lower decorative • Separate the two decorative duct covers.
Installation STEP 10 CONNECT Verify that power is turned WARNING: Instructions STEP 11 SLIDE DUCT COVER DOWN ELECTRICAL off at the source. fl,o.se wi,-ins.ot with a ground wire, a ground must be provided by the installer. When house wiring is aluminum, be sure to use UL approved anti-oxidant compound and aluminum-to-copper connectors.
Installation STEP 12 INSTALL FILTERS, FINALIZE Instructions INSTALLATION FilterSlots • Remove protective film on tile filters. • Tip tile filter into tile lower slots at tile rear of tile opening. I,ift tile filter and pull tlle knob forward until tile filter rests on tlle slots. • To remove tile filters, grasp tile knob and push filter towards tlle rear and tilt downwards. tile • Remove tlle protective film covering tile conuol panel on tile flont face of tile hood, and any other packaging materials.
Note: While performing installations described in this book, safety glasses or goggles should be worn. For Mo_wg,ram _°local ,_÷_vic_in yo_tr ar_a, call 1.800.444. 1845. Note: Prod uct improvement is a conthluhlg endeavor at (;enera] Electric. Therefbre, materials, appearance and specifications are subject to change _ithout notice. Monogram: Pub.No.49-80153-2 11-07 JR GEConsumer & Industrial GEAppliances General Electric" Company Louisville, KY 40225 ge.
