I I ® 30", 36" and 48" Professional Restaurant Style Vent Hoods Models: ZV48R ZV36R ZV30R
Safety Information READ AND SAVE THESE INSTRUCTIONS BEFORE YOU BEGIN Read these instructions completelg and carefullg. "IM PORTANT- Save these instructions for local inspector's use. "IM PORTANT- Observe all governing codes and ordinances. , Note to Installer - Be sure to leave these instructions with the Consumer. . Note to Consumer - Keep these instructions with gour Owner's Manual for future reference. , Skill Level -Installation of this appliance requires basic mechanical and electrical skills. .
Consignes de S@curit_ LISEZ ET CONSERVEZ CES INSTRUCTIONS AVANT DE COMMENCER Lisez ces instructions enti_rement B. et attentivement. "IM PORTANT- Conservez ces instructions pour I'inspecteur 61ectrique local. " IMPORTANT- Respecteztouslescodes et r_glementsen vigueur. . Remarque pour I'installateur - Assurez-vous de remettre ces instructions 6 I'utilisoteur. Remarque pour I'Utilisateur - Conservez ces instructions ovec votre notice d'utilisotion pour toute r6f@ence future.
Installation instructions CONTENTS Step 1, Determine Ductwork and Wiring Locations ............10 Product Dimensions .............................................................................. 4 Step 2A, Install Hood Onto Wall .................................................... !1 Installation Clearances ........................................................................ 5 Step 2B, Install Hood Beneath Soffit ........................................... 12 Optional Duct Cover Accessories .........
Advance Plannin INSTALLATION CLEARANCES OPTIONAL These vent hoods are designed to be installed onto a wall or beneath a soffit or cabinet. Installation with Warming Shelf , Hoods must be installed 32" min., 38" max. over any type cooking surfac when warming shelf is used. Installation without Warming Shelf , Install these hoods 30" min. to 36" max. above the cooking surface when installed over any professional style cooktop or range. ,These hoods may be installed 24" min.
Advance Plannin DETERMINE INSTALLATION HEIGHT, DUCT COVER ACCESSORIES These vent hoods must be installed 30" min. to 36" max. above the standard 36" high cooking surface. When installed with the warming shelf, allow 32" min. to 38" max. clearance. The exact hood installation height is determined bg the ceiling height. 1. Measure the exact ceiling height. 2. Review the chart at right to determine the range of possible hood installation heights that can be accomplished with one or more duct covers. 3.
Advance Planning ADVANCE PLANNING Ductwork Planning ,These vent hoods are equipped for !0" round ductwork. For best performance, use !0" round ductwork on the 48" wide hoods. 30" and 36" hoods mag be transitioned to 8" round. POWER SUPPLY IMPORTANT- (Please read carefullg) WARNING: FOR PERSONALSAFETY,THIS APPLIANCEMUSTBE PROPERLYGROUNDED. ,This hood mag be vented verticallg through upper cabinets, soffit or ceiling. A duct transition piece is supplied for vertical exhaust.
Advance Plannin DUCT FITTINGS Use this chart to compute maximum permissable lengths for duct runs to outdoors. 10" round to 8" round S ft. For best results, use 10" diameter duct. Note: Do not exceed maximum permissab/e equivalent Round, 1 ft. straight (per foot length) 90 ° elbow lO"Oia. Dia.17 24ft.ft. 8" 45 ° elbow lO" Dia. 14 ft. 8" Oia. i0 ft. Round wall cap 8" 10"Oia. Die.32 41ft.ft.
REMOVE THE PACKAGING . Remove packages from the "V" shaped cardboard section. Remove shipping pads. . Lift the hood out of the box. IMPORTANT: ', ", i--Transition ', Wood. Mountinc Support- ,L ..... Hood Lift the hood bg grasping the outside edges of the exhaust opening on the top. ,,,',, Motor _ ....... Parts ', ',, Mounted Shipping Carton set aside the mounting support with screws for later installation. DO NOT DISCARD. __. PARTS PROVIDED Heat Lamp Locate and check contents.
Installation ISTEP 11 DETERMINE HOOD, DUCTWORK instructions AND WIRING LOCATIONS , Use a level to draw the cooktop centerline location. Draw the line to ceiling height. , Measure desired distance from the bottom of the hood to the cooking surface. Note: If gou are installing the hood with duct covers, be sure to read "Using Duct Cover Accessories" page 7. Exact installation height mag be determined bg use of one or more duct covers.
Installation Instructions ISTEP 2A I INSTALL HOOD ONTO WALL IMPORTANT: upFraming must be capable supporting to 150 Ibs. SKIPTHIS STEPIF INSTALLING BENEATHA SOFFITOR CABINET, GO TO STEP2B. Install Transition Onto Top of Hood Locate at least 2 vertical studsat the wood support. Centerthe suppliedwood support, left to right and belowthe 20" marked line. I •-,, of Duct Transition IMPORTANT:Remove shipping tape from damper and check that damper moves freely. - ....
Installation instructions STEP 2B I Alternate Mounting Method INSTALL HOOD TO SOFFIT OR BENEATH CABINETS SKIPTHIS STEPIF USING WALL MOUNTING METHOD When necessary, the hood may be installed so that it is supported by the soffit. ,The soffit should be constructed with 2 x 4's. , Determine the installation location on the wall. , Continue the centerline forward on the bottom of the cabinet or soffit. IMPORTANT: Soffit framing supporting up to 150 Ibs.
Installation instructions [STEP 5 INSTALL DUCT COVERS STEP 3 CONNECT DUCTWORK , Install ductwork, making connections in direction of airflow as illustrated. , Secure joints in ductwork with sheetmetal screws. ,Wrap all duct joints with duct tape for an airtight seal. , Use duct tape to _>mP Air Flow seal the flange Duct Tape connection. Reach OverSea_ Screw inside the hood and and Screw Note: For easier handling, remove cardboard insert after film is peeled off. Remove protective film from duct covers.
Installation instructions STEP 7 INSTALL FILTERS . Drop grease trag into the hood. The rear tabs should engage the slots in the hood track. ,, Insert the grease filter into the opening and drop into the bottom. Raise filter to the top and lock into place. ,To remove the filters, grasp the handle, push the filter up and lift out. STEP 8 INSTALL BACKGROUND AND SHELF INSTALLBACKGUARD: . Remove packaging. . Place backguard against the bottom of the hood to use as a template.
Installation [STEP 91 INSTALL SHELF "ONLY" instructions I STEP 10 , Remove shelf packaging and protective film. , If installing the shelf alone, without the backguard, place shelf against the bottom of the hood and mark the screw hole locations "B" on the wall. , Drill two 1/8" pilot holes. , If the drill did not enter the studs, enlarge holes to 3/8". , Insert the wall anchors into the enlarged holes. Remove the screws from the wall anchors.
Note: While performing installations described in this book, safetg glasses or goggles should be worn. For Monogram ® local service in gour area, call 1.800.444.1845. Note: Product improvement is a continuing endeavor at General Electric. Therefore, materials, appearance and specifications are subject to change without notice. @ [49-80152-7 02-13 J GE Printed in Mexico Monogram: GE Consumer & Industrial GE Appliances General Electric Company Louisville, KV40225 GEApplionces.