I stall t I struct ® 0 30", 36" and 48" Professional Vent Hoods Models: ZV48T, ZV48S ZV36T, ZV36S ZV3OT, ZV30S
Safety Information READ AND SAVE THESE INSTRUCTIONS BEFORE YOU BEGIN Read these instructions completelg and carefullg. "IM PORTANT- Save these instructions for local inspector's use. "IM PORTANT- Observe all governing codes and ordinances. , Note to Installer - Be sure to leave these instructions with the Consumer. . Note to Consumer - Keep these instructions with gour Owner's Manual for future reference. , Skill Level -Installation of this appliance requires basic mechanical and electrical skills. .
Consignes de S@curit_ LISEZ ET CONSERVEZ CES INSTRUCTIONS AVANT DE COMMENCER Lisez ces instructions enti_rement B. et attentivement "IM PORTANT- Conservez ces instructions pour I'inspecteur 61ectrique local. " IMPORTANT- Respecteztouslescodes et r_glementsen vigueur. . Remarque pour I'installateur - Assurez-vous de remettre ces instructions 6 I'utilisoteur. Remarque pour I'Utilisateur - Conservez ces instructions ovec votre notice d'utilisotion pour toute r6f@ence future.
Installation instructions CONTENTS Product Dimensions ........................................................................... 4 Step 1, Determine Ductwork and Wiring Locations ............11 Installation Clearances ........................................................................ 5 Step 2A, Install Hood Onto Well ..................................................... 12 Step 2B, Install Hood Beneath Soffit ............................................ 13 Optional Duct Cover Accessories ..........
Advance Plannin INSTALLATION CLEARANCES OPTIONAL These vent hoods are designed to be installed onto a wall or beneath a soffit or cabinet. . Install these hoods* 30" rain, to 36" max. above the cooking surface, *These hoods mag be installed 24" min. above a gas or electric drop-in stgle cooktop. Alwags observe the 30" to 36" clearance when installed over ang professional stgle cooktop or range. Note: Clearances mag varg due to tgpe of cooking product and local codes.
Advance Plannin DETERMINE INSTALLATION HEIGHT, DUCT COVER ACCESSORIES These vent hoods must be installed 30" min. to 36" max. above the standard 36" high cooking surface when installed over any professional style rangetop or range. The exact hood installation height is determined by the ceiling height. 1. Measure the exact ceiling height. 2. Review the chart at right to determine the range of possible hood installation heights that can be accomplished with one or more duct covers. 3.
Advance Planning ADVANCE PLANNING Ductwork Planning ,These vent hoods are equipped for !0" round ductwork. For best performance, use 10" round ductwork on the 48" wide hoods. 30" and 36" hoods mag be transitioned to 8" round. POWER SUPPLY IMPORTANT-(Please read carefullg) ,& WARNING FOR PERSONALSAFETY,THIS APPLIANCEMUSTBE PROPERLYGROUNDED. ,This hood mag be vented verticallg through upper cabinets, soffit or ceiling. A duct transition piece is supplied for vertical exhaust.
Advance Plannin DUCT FITTINGS Use this chart to compute maximum permissable lengths for duct runs to outdoors. Note: Do not exceed maximum permissable equivalent lengths! Maximum recommended duct length for these hoods: 150 feet Flexible ducting: If flexible metal ducting is used, all the equivalent feet values in the table should be doubled. The flexible metal duct should be straight and smooth and extended as much as possible. (_ Do NOT use flexible plastic ducting. 20" round to 8" round 5 ft.
Installation Preparation TOOLS AND MATERIALS REQUIRED (NOT SUPPLIED) Duct tape Electric or batterg operated drill and !/8", 3/8" bits Keg Hole Saw Wirecutter/ stripper !0" round metal duct, length to suit installation. Penciland tape measure Safetgglasses Wire nuts Phillips and flat Spirit level blade screwdrivers Flashlight Step ladder Metal Snips !20V 60Hz. 15 or 20 Amp, 2-wire with ground. Properlg grounded branch circuit. Sabersaw or Sawsall REMOVE THE PACKAGING .
PARTS PROVIDED Locate the parts packed with the hood. Wood Support with Original Screws Duct Transition with Damper 2 Stainless Steel Grease Filters (3 filters with/48" models) Heat Lamp (2 with 48" models) 0000 Allen Wrench For Implement Rods 2 Grease Filter Trags (3 supports with 48" models.) 2 Implement Rods and/4 Stand-offs HARDWARE PACKAG E Locate and check contents. Screws shown actual size.
Installation ISTEP 11 DETERMINE HOOD, DUCTWORK instructions AND WIRING LOCATIONS . Use a level to draw the cooktop centerline location. Draw the line to ceiling height. . Measure desired distance from the bottom of the hood to the cooking surface, 30" min. to 36" max. Note: If gou are installing the hood with duct covers, be sure to read "Using Duct Cover Accessories" page 7. Exact installation height mog be determined bg use of one or more duct covers. .
Installation Instructions ISTEP 2A I INSTALL HOOD ONTO WALL IMPORTANT: upFraming must be capable supporting to 150 Ibs. SKIPTHIS STEPIF INSTALLING BENEATHA SOFFITOR CABINET, GO TO STEP2B. Install Transition Onto Top of Hood Locate at least 2 vertical studsat the wood support. Centerthe suppliedwood support, left to right and belowthe 15-3/8" marked line. LLL...... ',[ ..... : \\\, I ;'_r-- _ i] ...... " II IP ........
Installation instructions STEP 2B I Alternate Mounting Method INSTALL HOOD TO SOFFIT OR BENEATH CABINETS SKIPTHIS STEPIF USING WALL MOUNTING METHOD When necessarg, the hood mag be installed so that it is supported bg the soffit. *The soffit should be constructed with 2 x 4's. , Determine the installation location on the wall. , Continue the centerline forward on the bottom of the cabinet or soffit. IMPORTANT: Soffit framing supporting up to 250 Ibs.
Installation STEP 3 CONNECT DUCTWORK . Install ductwork, making connections in direction of airflow as illustrated. . Secure joints in ductwork with sheetmetal screws. . Wrap all duct joints with duct tape for an airtight seal. , Use duct tape to seal the flange connection. Reach inside the hood and push the dumper up to be sure it moves freelg. instructions STEP 5 INSTALL DUCT COVERS Note: For easier handling, remove cardboard insert after film is peeled off. Remove protective film from duct covers.
Installation STEP 7 INSTALL FILTERS instructions ISTEP 8] INSTALL IMPLEMENT RODS , Place filter drip troys into the reor of the hood. _rew Stond-offs // 0 "_"A_ i _ \! Into '!_ UseAllen Wrench to / SecureRod // to Stond-o_ , Use (_fiat blade screwdriver to install stc]nd-offs into the bottom of the hood. , Insert the grease filter into the opening (]nd drop into the tr(]gs. ,To remove the filters, grosp the handle, push the filter up and lift out.
Note: While performing installations described in this book, safety glasses or goggles should be worn. For Monogram ® local service in your area, call 1.aoo.444.184s. Note: Product improvement is a continuing endeavor at General Electric. Therefore, materials, appearance and specifications are subject to change without notice. Monogram: 149-80151-8 02-13 ] GE Printed in Mexico GE Consumer & Industrial GE Applionces General Electric Compony Louisville, KV40225 GEApplionees.