GE Monogram ® Installation Instructions 36" Island Vent Hood Model ZV850 Monogram°
Before you begin - Read these instructions completely and careflllly. IMPORTANT - Save these instructions for local inspector's use. IMPORTANT - OBSERVE AI,L GOVERNING (;ODES AND ORDINANCES. Note to Installer - Be sure to leave these instructions with the Consumer. Note to Consumer - Keep WARNING: This appliance these instructions must be properly with your grounded.
Design Intormation 36" Island Model Available Model ZV850 Required Aeeesso U ZX858 - Fox 8 ft. ceiling height. This kit includes decorative duct This vent hood is designed to be used in vented ceiling mounted installations. covers and support flames to reach an 8 ft ceiling height. ZX859 - Fox 9 ft. ceiling height. This kit includes decorative duct covers and support flames to reach an 9 ft ceiling height. Reeireulating Operation This hood may be installed for recirculadng operation.
Design Intormation 36" Island Usinff Duct Cover Accessories Vent Hood A duct cover accessory is required for all ceiling heights. Use this chart to determine the correct Duct Cover Accessory for 8 ft. to 10 ft. ceilings that must be ordered with the hood. ZV850SBInstallation Heights Actual Ceiling * PossibleHood Height Installation Height 7' 11" Duct Cover Accessory 24-1/2" >o o3 co co 8'0" 25-1/2" IJJ oX ¢o _.
Installation Preparation 36" Island 7bols and Materials Required (not supplied) • Tapemeasure • Knife • 120V60Hz. 15 or 20 Amp, 2 wire with ground. Properly grounded branchcircuit. • Strain relief for junction box cover.
Installation Preparation 36" Duct fittincs Use this chart Island Vent Hood to compute maximum permissable lengths for duct runs to outdoors. Total Duct Piece Dimensions Equivalent I,ength* Ro lit. t/Ild, straight Equivalent I,ength (per foot length) Note: Do not exceed maximumpermissable equivalent lengths! Quantity Used lit. /_ straight 3-1/4" (per fbot x 10" length) Maximumductlength: 100footforrangehoods. Q_ 90 ° elbow 12 It. 45 ° elbow 7 It.
Installation Preparation 36" Island Plan the location Determine the exact location Ceiling of the vent hood. • Use a plumb to check location to be sure countertop/cooktop location below the hood will align exacdy. • The hood should project forward 1-1/2" beyond the flont edge of the cooking appliance. See illusuadon. • Observe the recommended 25-1/2" space between the cooking surface and bottom of hood. Advance Planning Vent Hood I i Hood :....]z D_ttinllne Jl Front ..........................
Installation Preparation 36" Island Vent Hood s1 Advance Planning (continued) • Arrange cross flatning in tile ceiling to suit tile existing structure. See examples. - Secure each 2 x 4 block with at least four (4), #10 wood screws, 3" long (minimum size screws, not supplied). Use 8 wood screws total for tile two supports. • The cross framing must be accurately aligned to assure correct positioning of the hood. • The cross framing must be level in all directions.
Installation 36" Remove the Paekacin¢ Islan, d Vent Hood The vent hood is packed separately flom the required accessory ZX858, ZX859 or ZX8510. • Remove the flame, cove_; parts box, side bars and packaging. • Remove junction box cover. • Install suain relief onto junction box coveL I,ocate the hardware accesso_ T box packed with the hood and check contents. /o o \ E Cheek Installation Hardware 4 Flat Washers 8 Frame Attachment Screws with Washers 4 Hexhead wood lag screws (6mm x 2-1/2") g or
Installation 36" Island /o • Align the template with the marks on the ceiling and tape in place. - Be sure the template is oriented correctly, with the fiont of the hood. Template • Use a plumb to be sure the mounting holes will provide parallel alignment with the countertop below. • Center punch all hole locations. • Drill pilot holes in the 4 screw locations. Use a 5/32" bit and drill approximately 1-1/2" deep. • Cut the 6-1/4" dia. duct opening and approx. 1" dia. wire access hole. o \ o FrontofHo
Installation 36" Island Vent Hood Wiring • Route house Mring through the ceiling hole and pull a length to reach the hood junction box, approximately 6" below the support. • Tape the wire to the flont of the flame support to prevent damage during installation and service. # Ce!ling FrontSide Support Frames r77 _ '\\\ ? ? o ? o )Tape ? / / J /. :- House \^I;4% s,e 7 Size And Install Duetworh To Find Required Duct Length: • Measure flom house duct flange to bottom of support flame.
Installation 36" Island Vent Hood Se8 Install Decorative Duct Covers TopDuct Pretap 2 Screw / Holes .1 Install Screwon EachSide i-l Dover Bottom Duct Cover TopDuct Cover BottomDuct Cover f_ / Top Duct Cover // --\\\ ,,,(Stop Screw oX..... Install Stop Screw in One of 3 Holes • Premp or drive decorative screw into the screw holes on the support flame. This will make screw installation easier. • Separate the two decorative duct covers.
Installation 36" Island Bottom Align Duct Connectorto .. HouseDuct / Align Mounting Studs TO mounting wrencll. Electrical Verify studs. that power Tighten is turned • Check hood j / --l /4,ock H II[ot _ • I,ifl the hood up to the support frame. Carefldly align tim hood mounting studs into the support flame holes, and at tim same time, guide tim hood duct connector into tim house duct.
Installation 36" Island Vent Hood J J Slide Duct Cover Down, Install Side Utility Bars 1 • Hold the deco_afive duct cove_ and _emove the tempora_y stop sc_ew. Retmn the sctew to the seevice manual envelope foi fllttl_e use. • Slide the lower duct cover down onto the hood. 14 • Install the side utility ba_s with screws as shown.
Installation 36" Island Vent Hood \ \ \ \ Install Filters \ LowerFilter Slots • Remove protective film on filters. • Tip the filter into the lower slots at the rear of the opening. I,ift the filter and pull the knob forward until the filter rests on the slots. • To remove the filters, grasp the knob, push the filter towards the rear and flit downwards. e 13 Finalize Installation • Remove the protective film covering the conuol panel on the flont face of the hood, and any other packaging materials.
NOTE: book, While safer} performing glasses I+br Mo_og'ram 1.800.444.1845. Monogram: GEConsumer & Industrial GEAppliances GeneralElectric Company Louisville,KY40225 monogram, NOTE: Prod/let There[k_re, witho/lt installations or goggles local service impro\vment materials, appearance should described in this be worn. i_ )'our area, call is a continuing and endea specifications or are at General s/ll_ject Electric. to change notice. Pub. No. 49-8970-2 04/07.
