Call 1-800-667-8721 anywhere in the US and Canada - www.rangehoods.com at :: rangehoods . com Installation Instructions ZV950 36" Stainless Steel Vent Hood Monogram. ® We bring good things to life. GE Monogram at :: rangehoods .
Call 1-800-667-8721 anywhere in the US and Canada - www.rangehoods.com Safety Information BEFORE YOU BEGIN WARNING: TO REDUCE THE RISK Read these instructions completely and carefully. • OF FIRE, ELECTRICAL SHOCK OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: A. Use this unit only in the manner intended by the manufacturer. If you have any questions, contact the manufacturer. B.
Call 1-800-667-8721 anywhere in the US and Canada - www.rangehoods.com Design Information CONTENTS Ductwork, Wiring Locations ............................................ 7 Installation Instructions Step 1, Install Framing for Hood Support ...................... 8 Step 2, Install Mounting Brackets .................................... 8 Step 3, Install Duct Bracket .............................................. 9 Step 4, Install the Hood ...................................................
Call 1-800-667-8721 anywhere in the US and Canada - www.rangehoods.com Installation Preparation ADVANCE PLANNING Ductwork Planning • Determine the exact location of the vent hood. • Plan the route for venting exhaust to the outdoors. • Use the shortest and straightest duct route possible. For satisfactory performance, duct run should not exceed 100 equivalent length for any duct configurations. • Refer to “Duct Fittings” chart to compute the maximum permissible length for duct runs to the outdoors.
Call 1-800-667-8721 anywhere in the US and Canada - www.rangehoods.com Installation Preparation DUCT FITTINGS Duct Piece Use this chart to compute maximum permissable lengths for duct runs to outdoors. Note: Do not exceed maximum permissable equivalent lengths! Maximum duct length: 100 foot for 8" round duct 75 foot for 3-1/4" x 12" duct Flexible ducting: If flexible metal ducting is used, all the equivalent feet values in the table should be doubled.
Call 1-800-667-8721 anywhere in the US and Canada - www.rangehoods.com Installation Preparation TOOLS AND MATERIALS REQUIRED (NOT SUPPLIED) • Tape measure • Knife • Spirit level • Wire cutter/stripper • Wire nuts • Electric drill with 1/8" and 3/8" bits • Phillips and flat blade screwdrivers • Hammer • Pliers • Safety glasses • Duct tape • Tape to mount template • Gloves to protect against sharp edges • 120V 60Hz. 15 or 20 Amp, 2 wire with ground. Properly grounded branch circuit.
Call 1-800-667-8721 anywhere in the US and Canada - www.rangehoods.com Installation Preparation DUCTWORK, WIRING LOCATIONS CHECK INSTALLATION HARDWARE Determine the exact location of the vent hood. • Locate the template packed with the literature. – Measure 36" from the floor to the top of the cooking surface. Add 25-1/2" (or other recommended space) from the cooking surface to the bottom of the hood. Mark that location. – Use a level to draw a straight pencil line on the wall.
Call 1-800-667-8721 anywhere in the US and Canada - www.rangehoods.com Installation Instructions 2 INSTALL MOUNTING BRACKETS 1 INSTALL FRAMING FOR HOOD SUPPORT This vent hood must be secured to the horizontal support or wall studs. IMPORTANT: Framing must be capable of supporting 100 lbs. • With the template taped in place, use a punch to mark all mounting screw locations. • Drill 1/8" pilot holes at the 6 punched locations. • Remove the template.
Call 1-800-667-8721 anywhere in the US and Canada - www.rangehoods.com Installation Instructions 3 INSTALL DUCT BRACKET The duct bracket must be installed against the ceiling. This bracket will hold the decorative duct cover in place at the top. • Install the 2 small screws into the sides of the duct bracket. Remove the screws. Pre-tapping the holes will insure ease of final installation. Pre-Tap Side Screw Pre-Tap Side Screw Secure the bracket to the ceiling and wall: • Mark the 4 screw hole locations.
Call 1-800-667-8721 anywhere in the US and Canada - www.rangehoods.com Installation Instructions 5 CONNECT DUCTWORK • Install ductwork, making connections in direction of airflow as illustrated. • Push duct over the exhaust outlet until it reaches the duct stops. • Secure joints in ductwork with sheetmetal screws. • Wrap all duct joints with duct tape for an airtight seal. • Use duct tape to seal the flange connection.
Call 1-800-667-8721 anywhere in the US and Canada - www.rangehoods.com Installation Instructions 8 INSTALL FILTERS • Remove protective film on the filters. • Tip the filter into the slots at the rear of the opening. Lift the filter and pull the knob forward until the filter rests on the slots. • Install all 3 grease filters. • To remove the filters, grasp the knob, push the filter towards the rear and tilt downwards.
