Quick Specification

ManualsBrandsMonogram ManualsWarming DrawersMonogram 30" Stainless Steel Warming Drawer

PAGE 1 OF 6

For questions about your

appliance, please call 1-800-626-2000.

Product Specication Revised 6/20

1.9 CU. FT CAPACITY

"ON" INDICATOR LIGHT

INFINITE SETTING TEMPERATURE CONTROL

75 Degrees to 230 Degrees

VARIABLE HUMIDITY CONTROL

Crisp to Moist

REMOVABLE HALF RACK

ACCEPTS 3/4" TRIMLESS CUSTOM PANEL

AND CUSTOM HANDLE WITH TRIM KIT

FULL EXTENSION DRAWER ON BALL BEARING

GLIDES

ACCEPTS OPTIONAL STATEMENT PANEL KIT

VARIABLE INSTALLATION OPTIONS

ON/OFF ROCKER SWITCH

MONOGRAM 30" WARMING DRAWER

ZW9000SJSS

Summary of content (6 pages)

PAGE 1
MONOGRAM 30" WARMING DRAWER ZW9000SJSS 1.9 CU. FT CAPACITY "ON" INDICATOR LIGHT INFINITE SETTING TEMPERATURE CONTROL 75 Degrees to 230 Degrees VARIABLE HUMIDITY CONTROL Crisp to Moist REMOVABLE HALF RACK ACCEPTS 3/4" TRIMLESS CUSTOM PANEL AND CUSTOM HANDLE WITH TRIM KIT FULL EXTENSION DRAWER ON BALL BEARING GLIDES ACCEPTS OPTIONAL STATEMENT PANEL KIT VARIABLE INSTALLATION OPTIONS ON/OFF ROCKER SWITCH For questions about your appliance, please call 1-800-626-2000.
PAGE 2
OVERALL DIMENSIONS 29 3/4" (75.5) 25 19/32" (65) handle width SPECIFICATIONS Overall Width 29 3/4" (75.5 cm) Overall Height 10 1/2" (26.7 cm) Overall Depth 23 1/4" (59.0 cm) Drawer Capacity 1.90 cu. ft. (53.8 l) Cut-out Width 28 1/2" (72.4 cm) Cut-out Height 9 1/4" (23.5 cm) Cut-out Depth 23 1/2" (59.7 cm) Power Cord Length 56" (142.2 cm) Electrical Rating 450W @ 120V/60Hz Total Amps 15 Amps Net Weight 59 lbs. (26.8 kg) Approx. Shipping Weight 65 lbs. (29.6 kg) 1 3/32" (2.
PAGE 3
INSTALLATION BELOW SINGLE OR DOUBLE WALL OVEN HELPFUL TIPS A W arming drawers are approved for installation below only certain specified wall oven and cooktop models. See the label attached to the top of the warming drawer for approved combinations. TOP VIEW TOP VIEW ZDT910SFSS ZDT910SFSS Side Sidecleats cleats B A dditional clearance between cut-outs may be required.
PAGE 4
INSTALLATION BELOW A CABINET DRAWER HELPFUL TIPS TOP VIEW A If you are installing in frameless cabinets, it may be necessary to install 1/2" wide cleats to accept drawer mounting screws. See drawer for mounting screw locations. Side cleats TOP VIEW ZDT910SFSS Side cleats ZDT910SFSS A B I nstall a 2"x2" or 2"x4" anti-tip block against rear wall, 9" from floor of cutout to bottom of block. The anti-tip block must be installed to prevent the drawer from tipping forward when opened and loaded.
PAGE 5
HELPFUL TIPS INSTALLATION WITH CUSTOM PANEL KIT - ZXD30B 3/4" (1.9) max. 30" (76.2) 10 1/2" This kit contains a mounting panel to support a trim-less custom drawer front up to 3/4" thick. The original tubular handle can be reinstalled onto the custom panel with longer screws (not provided) or can be replaced with a custom handle of your choice (also not provided). 1 13/16" (4.6) (26.7) Drill 5/16" (0.8) through custom panel for lamp jewel 1 3/4" (4.
PAGE 6
INSTALLATION WITH STATEMENT STYLE PANEL KIT - ZXD9030PN 29 3/4" (75.5) 29 1/2" (74.9) 3/4" (1.9) Handle width 9 1/4" 10 1/2" (23.5) Cutou-out height (26.7) HELPFUL TIPS This kit contains a stainless steel statement style panel with a handle and lamp jewel embedded in the bottom right side. This is a onepiece assembly that replaces the original drawer front and tubular handle. The original tubular handle (or a custom handle) cannot be installed onto this professional drawer panel.