Quick Specification

For questions about your
appliance, please call 1-800-626-2000.
HELPFUL TIPS
PAGE 4 OF 6 Product Specication Revised 6/20
A
If you are installing in frameless
cabinets, it may be necessary to install
1/2" wide cleats to accept drawer
mounting screws. See drawer for
mounting screw locations.
B
Install a 2"x2" or 2"x4" anti-tip block
against rear wall, 9" from oor of cutout
to bottom of block. The anti-tip block
must be installed to prevent the drawer
from tipping forward when opened and
loaded. Failure to add the anti-tip block
could result in personal injury.
C
When installing the warming drawer
below a cabinet drawer, a solid barrier
must be installed at least above the
warming drawer to block access. Use
any solid material such as 1/4" thick
plywood. Allow at least 1/4" air gap
between the barrier and the top of the
warming drawer. Observe the 5" min.
above the oor or 1" min. above the toe
kick installation height.
D
When installing two warming drawers
side by side, install them in separate cut-
outs and allow a 2" min. gap between
each cut-out.
E
The warming drawer may be supported
by either a solid bottom or 2"x2" or
2"x4" runners. The support must be
level and rigidly mounted, ush with
the bottom edge of the cut-out (there
is no way to level the drawer once it
has been installed, so make sure that the
supports are level). The oor or runners
must be capable of supporting at least
150 lbs.
For more details refer to the installation
instructions for this product.
PROVIDING CABINET SUPPORT INSTALLING ANTI-TIP BLOCKS
SIDE BY SIDE INSTALLATION
SIDE VIEW
FRONT VIEW
TOP VIEW
28 1/2" (72.4)
min. cutout width
23 1/2" (59.7)
min. cutout width
1/4"
(.6)
min.
1"
(2.5)
min.
Above
toe-kick
2" (5.1) min.
Between cut-outs
2" (5.1) x 4" (10.2)
or Equivalent Runners
Install
2" (5.1) x 4" (10.2)
or
2" (5.1) x 2" (5.1)
Anti-tip Block against
rear cabinet wall 9" from
floor to bottom of block
Side cleats
9 1/4"
(23.5)
Cut-out
height
30" (76.2)
25" (63.5)
23 1/2"
(59.7)
2" (5.1) x 4" (10.2)
or
2" (5.1) x 2" (5.1)
Runners or Solid Bottom
ZDT910SFSS
SIDE VIEW
FRONT VIEW
TOP VIEW
28 1/2" (72.4)
min. cutout width
23 1/2" (59.7)
min. cutout width
1/4"
(.6)
min.
1"
(2.5)
min.
Above
toe-kick
2" (5.1) min.
Between cut-outs
2" (5.1) x 4" (10.2)
or Equivalent Runners
Install
2" (5.1) x 4" (10.2)
or
2" (5.1) x 2" (5.1)
Anti-tip Block against
rear cabinet wall 9" from
floor to bottom of block
Side cleats
9 1/4"
(23.5)
Cut-out
height
30" (76.2)
25" (63.5)
23 1/2"
(59.7)
2" (5.1) x 4" (10.2)
or
2" (5.1) x 2" (5.1)
Runners or Solid Bottom
ZDT910SFSS
SIDE VIEW
FRONT VIEW
TOP VIEW
28 1/2" (72.4)
min. cutout width
23 1/2" (59.7)
min. cutout width
1/4"
(.6)
min.
1"
(2.5)
min.
Above
toe-kick
2" (5.1) min.
Between cut-outs
2" (5.1) x 4" (10.2)
or Equivalent Runners
Install
2" (5.1) x 4" (10.2)
or
2" (5.1) x 2" (5.1)
Anti-tip Block against
rear cabinet wall 9" from
floor to bottom of block
Side cleats
9 1/4"
(23.5)
Cut-out
height
30" (76.2)
25" (63.5)
23 1/2"
(59.7)
2" (5.1) x 4" (10.2)
or
2" (5.1) x 2" (5.1)
Runners or Solid Bottom
ZDT910SFSS
A
A
D
E
B
B
C
INSTALLATION BELOW A CABINET DRAWER