MTM 3-Way Powered Desktop Speakers P/N 43241 User's Manual
SAFETY WARNINGS AND GUIDELINES Please read this entire manual before using this device, paying extra attention to these safety warnings and guidelines. Please keep this manual in a safe place for future reference. • This device is intended for indoor use only. • Do not expose this device to water or moisture of any kind. Do not place drinks or other containers with moisture on or near the device.
• Do not expose this device to excessively high temperatures. Do not place it in, on, or near a heat source, such as a fireplace, stove, radiator, etc. Do not leave it in direct sunlight. • Do not place or install this device in an area where it can be exposed to excessive amounts of dust, humidity, oil, smoke, or combustible vapors. • Prior to operation, check the unit and power cord for physical damage. Do not use if physical damage has occurred.
FEATURES • One 1.25" silk dome tweeter in each speaker • Two 4" woofers in each speaker • Two 5.25" passive radiator drivers in each speaker • Separate 50-watt Class D amplifiers for each speaker • 50Hz ~ 20kHz frequency response • Bluetooth® 5 with Qualcomm® aptX™ HD codec • Subwoofer output • 3.
PACKAGE CONTENTS Please take an inventory of the package contents to ensure you have all the items listed below. If anything is missing or damaged, please contact Monoprice Customer Service for a replacement.
PRODUCT OVERVIEW Primary Speaker Front Panel 1. Headphone: 3.5mm stereo 2. Tweeter: One 1.25" silk dome 3. Woofers: Two 4" woofers. headphone jack. tweeter. 4. Volume: Multifunction knob and source LED indicators. With the speakers powered on, rotate the knob to increase or decrease the volume level. With the speakers powered off, momentarily press the knob to turn the speakers on.
Primary Speaker Side Panels 6. Passive Radiators: Two 5.25" passive radiators (one on each side).
Primary Speaker Rear Panel 1. AC INPUT: IEC 60320 C8 connector for connecting the included AC Power Cord. 2. USB: USB Type-C® input. 3. OPTICAL: Digital optical S/PDIF input. 4. ANALOG INPUTS: Stereo RCA inputs. 5. SUBWOOFER OUTPUT: Mono RCA output for connecting a subwoofer (available separately). 6. SPEAKER OUT: Connectors for connecting the Secondary Speaker using the included Speaker Interconnect Cable. 7. POWER: Switch for turning the speakers on or off.
Remote Control 1. ON/STANDBY: Press the button to turn the speakers on or to put them into standby mode. Note that the POWER switch on the Primary Speaker Rear Panel must be in the ON position for this button to function. 2. TONE DEFEAT: Press the button to bypass the tone controls for an unaltered audio signal, without changing the tone control settings. Press the button again to reinsert the tone controls into the audio signal path. 3. PAIR: Press the button to enter Bluetooth® pairing mode. 4.
INSTALLATION Ensure that power is turned off and disconnected on all equipment to be connected before making any electrical connections. 1. Ensure that the POWER switch on the Primary Speaker Rear Panel is 2. Place the Primary Speaker and Secondary Speaker in their intended 3. Connect one end of the included Speaker Interconnect Cable to in the OFF position. locations.
8. Plug one end of the included AC Power Cord into the AC INPUT on the Primary Speaker Rear Panel, then plug the other end into a nearby AC power outlet. 9. Open the battery compartment cover on the included Remote Control and insert the included AAA Batteries, taking care to match the polarities on the batteries with the polarity markings inside the battery compartment.
• After 30 minutes of no audio signal input, the speakers will automatically enter standby mode. The LED on the Primary Speaker Front Panel corresponding to the last used input will blink slowly. The last set volume level and input will be restored when the speakers are powered back on. • Place the POWER switch on the Primary Speaker Rear Panel in the OFF position to turn the speakers fully off, without going into standby mode.
5. Locate and select the MP43241 entry. If prompted for a passcode, input 0000 (four zeros). Once the connection is established, the BT LED on the Primary Speaker Front Panel will cease flashing and will illuminate steadily, indicating that the Bluetooth connection has been successfully made. Note that the speaker will remember the device it was last paired to. To reconnect after the connection has been broken, open the Bluetooth settings on your device and select Connect to reestablish the connection.
SPECIFICATIONS P/N 43241 Frequency Response 50Hz ~ 20kHz Woofer Drivers (each) 2x 4" cone Tweeter Driver (each) 1x 1.25" silk dome Passive Drivers (each) 2x 5.25" passive radiators Amplifier Type Class D Amplifier Output Power 2x 50 watts Inputs Outputs Stereo analog RCA, digital optical S/PDIF, USB, Bluetooth® Mono analog subwoofer, stereo 3.
TECHNICAL SUPPORT Monoprice is pleased to provide free, live, online technical support to assist you with any questions you may have about installation, setup, troubleshooting, or product recommendations. If you ever need assistance with your new product, please come online to talk to one of our friendly and knowledgeable Tech Support Associates. Technical support is available through the online chat button on our website www.monoprice.com or through email by sending a message to tech@monoprice.com.
exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
EU Conformity with applicable directives This equipment complies with the essential requirements listed below: • Radio Equipment Directive (RED) 2014/53/EU • RoHS 2 Directive 2011/65/EU with Directive (EU) 2015/863 UK Conformity with the relevant Union harmonization legislation This equipment complies with the essential requirements listed below: • Radio Equipment Regulations 2017 • Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment Regulations 2012 17
Monoprice™, Monolith™, the Monolith logo, and all Monoprice logos are trademarks of Monoprice Inc. The Bluetooth® word mark and logos are registered trademarks of Bluetooth SIG, Inc. Qualcomm® is a trademark of Qualcomm Incorporated, registered in the United States and other countries. aptX™, aptX™ HD, and the aptX™ logos are trademarks of Qualcomm Technologies International, Ltd. Qualcomm® aptX™ and Qualcomm® aptX™ HD are products of Qualcomm Technologies International, Ltd.