2DNR 3-Axis Gimbal Vari-focal Vandal Resistant Dome Camera
8 Mounting Housings to Electrical Junction Boxes 9 10 11 12~24 Fan & Heater (Option) 25 26~27
SERVICE MONITOR & CONTROL CABLE FH Torx Wrench: Length 90mm (1pc) Dowel: Length 30mm, Thickness 6mm (4pcs) Assembly Screws: FH M4x14 (4pcs) - These screws are used to affix flush mount base to surface mount plate. Mounting Screws: - These screws are used to mount both surface mount plate or flush mount base to a sturdy surface. If necessary, use the dowels included.
1/3” Sony Super HAD II High-resolution Color CCD 600TVL High-Resolution 2.8 ~ 10.5mm Vari-Focal, DC Auto Iris F1.2 Lens - Option: 2.8~11mm F1.2, 3.8~9.5mm F1.
100 152 50 126 50 20 102 32 149 116
1. Bubble 2. Dome Cover Ring 3. Lens 4. Safety Wire 5. Service Monitor Output Port 6. Flush Mount Base 7. Surface Mount Plate 8. Assembly Screws (M4x8) 9. Assembly Screws (FH M4x14) 10. Gimbal-Bracket 11. Mounting Screws (ST4x38) 12. Video/Power Cable To avoid smear, do not expose the camera directly to a strong light source such as the sun or spot light.
FH
Screws, FH M4x14
- All camera models are supplied with service monitor output the inside units. If you need to set up OSD menu, use the service monitor and control cable.
Rotation Rotation loosen the lever bolt and make necessary Focus adjustments. lever bolt Loosen Zoom& Focus lever bolt and Zoom lever bolt 3. After adjustments, tighten the lever bolts to lock. ZOOM/FOCUS LEVER DETAIL VIEW LOCK UNLOCK T T UNLOCK LOCK f=2.8~10.5mm 11 f=2.8~11mm, 3.8~9.
> SET Key: Access to the menu or confirm the setting. To enter the main menu, press the SET Key once. > UP/DOWN Key : Choose the desired sub-menu. > LEFT/RIGHT Key : Set up the value of the selected menu. Used to adjust the desired menu selection, and to move the cursor left or right.
WHITE BAL. ATW1 ATW2 BACKLIGHT AWC->SET AWC->SET (PUSH) MANUAL COLOR TEMP. MANUAL BLUE 0~255 RED 0~255 RETURN RET/END COLOR TEMP. INDOOR BLUE -- RED -- RETURN RET/END COLOR TEMP.
IMAGE ADJ. LENS SHAD. ON/OFF 2DNR ON/OFF MIRROR ON/OFF FONT COLOR FRONT 0~15 ID & TITLE 0~15 RETURN RET/END CONTRAST 0~255 SHARPNESS DISPLAY 0~31 CRT PED LEVEL(0~63) COLOR GAIN(0~255) LCD RETURN(RET/END) GAMMA(0.05~1.00) PED LEVEL(0~63) COLOR GAIN(0~255) RETURN(RET/END) USER GAMMA(0.05~1.00) PED LEVEL(0~63) COLOR GAIN(0~255) RETURN(RET/END) SPECIAL NEG. IMAGE ON/OFF RETURN RET/END CAM TITLE ON/OFF DAY&NIGHT * AURO/COLOR/BW/EXT MOTION AREA SEL.
SPECIAL MOTION PRIVACY RESET TOP/BOTTOM 0~15 DEGREE 0~255 VIEW ON/OFF RETURN RET/END AREA SEL. AREA1~AREA8 AREA STATE ON/OFF HEIGHT 0~15 WIDTH 0~15 LEFT/LIGHT 0~15 TOP/BOTTOM 0~15 COLOR 0~15 RETURN RET/END DPC AUTO DEFECT(64 point) VERSION 00,00,01 RETURN RET/END FACTORY RESET RETURN RET/END EXIT DAY&NIGHT * : Standard type cameras do not support the DAY&NIGHT function.
The Setup is used to control and adjust the many features and options available on your camera. Read thoroughly before making any adjustments. Note: These options have been pre-configured at the factory for optimal performance. SETUP LENS EXPOSURE WHITE BAL. BACKLIGHT IMAGE ADJ. SPECIAL RESET EXIT DC ATW1 BLC LENS This is always set on DC and cannot be changed. EXPOSURE SHUTTER: (AUTO, FLK, 1/60(1/50) ~ 1/100,000) The SHUTTER speed can be selected manually to user preference.
> AUTO: Select the AUTO mode for automatic adjustment of the shutters. It will slow down or speed up depending on the environment. > FLK: Select the FLK mode if the screen flickers due to differences in light and electric frequencies. BRIGHTNESS: 0~255 The BRIGHTNESS can be adjusted by opening and closing of the Iris aperture. User may fine-tune the screen to their preferred brightness. The brightness ranges from 0~255.
ATW1 (Auto Tracing White Balance mode 1): Select the ATW1 mode to automatically adjust the color temperature according to its ambient condition. (2,300~9,500K) ATW2: Select the ATW2 mode if the color temperature of the light source is between 2,000~11,000K. AWC (Auto White Balance Control): Use the AWC function to correctly calibrate the white balance of the camera. While in this mode, press the SET key while placing a white sheet of paper in front of the camera.
> AREA SEL. (AREA1~AREA2): Choose one of two pre-defined boxes to adjust its size or location. > AREA STATE (ON, OFF): Select a box active or inactive for BLC. > HEIGHT, WIDTH: Adjust the height or width of the area. > LEFT/RIGHT, TOP/BOTTOM: Changes the location of the defined area. > RETURN: Select RET to save and exit, and to go back to the MAIN MENU. HLC (High Light Compensation): The HLC masks out excessively bright areas within the frame and compensates the rest accordingly.
FRONT COLOR Change the OSD menu front color to user preference when there isn’t enough contrast between the picture and the menu to distinguish the letters. > FRONT: Choose from the 15 available colors. > ID&TITLE: Choose from the 15 available colors. CONTRAST: 0~255 Adjust the contrast of image, the difference between light and dark areas on the screen. SHARPNESS: 0~31 Adjust the display image sharpness.
Programing the Camera ID: 1. Press the LEFT or RIGHT key to turn On the Camera Tiltle mode. 2. While Camera ID function is On, press the SET key to enter the sub-menu. 3. Using the directional navigation keys, choose from alphabetical letters and numbers to create a 15-digit Camera ID. 4. Move the cursor to POS and press the SET key. The Camera ID will appear on the bottom center. 5. Using the directional navigation keys, change the position of the Camera Title to the desired location. 6.
> AUTO: The Color mode is operated during daytime and automatically converts to B/W mode in the absence of light during night-time. AGC cannot be modified in this mode. D => N Level This level determines the level of darkness before switching from Day mode to Night mode. D => N Delay This function is used to set the delay between switching of the modes. If the delay has been set to ‘3’, the camera will observe darkness for at least 3 seconds before switching to Night mode.
> AREA SEL. (AREA1~4): Choose one of four pre-defined boxes to adjust its size or location. > AREA STATE (ON,OFF): Select a box active or inactive for motion detection. > HEIGHT, WIDTH: Adjust the height or width of the area. > LEFT/RIGHT, TOP/BOTTOM: Changes the location of the defined area. > DEGREES (0~255): Increases or decreases the sensitivity of the selected area. Increasing the number decreases sensitivity. > VIEW (ON,OFF): Turns the “Running Man” indication On or Off.
RETURN Selects “RET” to save and exit, and to go back to the MAIN MENU. RESET This function is used to reset all camera settings to the factory default settings. EXIT Choose EXIT to save and exit from the menu mode.
- For Fan & Heater operation, AC24V power input is required. - UTP models and DC12V operation models are not supported Fan & Heater function.
Common Specification 1/3” Interline Transfer Type Color CCD (Sony) 1/60sec, FLK, Auto(1/60 ~ 1/100,000sec) 1/50sec, FLK, Auto(1/50 ~ 1/100,000)sec More than 48dB (AGC Off) ATW1 / ATW2 / AWC / Manual (ATW1: 2,300 ~9,500°K, ATW2: 2,000 ~11,000°K) On/Off DWDR On/Off 152mm 26 126mm
Standard Type 600TVL 0.2Lux @F1.2 f = 2.8~10.5mm Vari-Focal, DC Auto Iris F1.2 Lens (Option: 2.8~11mm F1.2, 3.8~9.5mm F1.2) DC12V Max.: 100mA/DC12V AC24V/DC12V Max.: 4.8VA/AC24V, 150mA/DC12V Day & Night Type 600TVL(Color), 650TVL(B/W) Day&Night Functionality ICR type on EXT(photocell) 0.2Lux (Color), 0.02Lux (B/W) @F1.2 f = 2.8~10.5mm Vari-Focal, DC Auto Iris F1.2 D/N Lens (Option: 2.8~11mm F1.2, 3.8~9.5mm F1.2) DC12V Max.:110mA/DC12V AC24V/DC12V Max.:5.
2DNR 3-Axis Gimbal Vari-focal Vandal Resistant Dome Camera ML11052V6400A
