SUPERTHIN Small Tilt MOUNT ™ SECURE, EASY TO INSTALL, LOW PROFILE Tilting MOUNT Installation manual and warranty 10 "–27" (25-68cm) 40 lbs. (18.
SuperThin Small TILT Mount ™ This SuperThin mount is designed to mount 10"– 27" (25 – 68 cm) flatscreen televisions to vertical walls. Maximum weight capacity is 40 lbs. (18.14 kg). Before installing, carefully review the instructions to ensure that no parts are missing or defective. Improper installation can cause damage or serious injury. Do not use this product for any purpose not explicitly specified by Monster or the manufacturer.
4.72" (12.0cm) 2.95" (7.5cm) 2.95" (7.5cm) 3.94" (10.0cm) 3.94" (10.0cm) 2.95" (7.5cm) 4.72" (12.0cm) 1.7" (4.3cm) Specifications and Notes VESA 75×75 / 100×100 Compliant ™ Monster is constantly striving to improve its products. Specifications are subject to change without notice.
1 Wall Mounting Plate Security Screw 2 each M4×12 1 TV Mounting Plate 2 Concrete Anchors 2 Lag Bolts 2 Round Washers Screws 4 each M4×15 4 each M5×15 1 Bubble Level Package Contents If any parts are missing, please call the appropriate Monster number for your location. See page 2 for phone numbers.
Important! Read Before Installing WARNINGS CAUTIONS A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions. A CAUTION alerts you the possibility of damage or destruction of equipment if you do not follow the corresponding instruction. (1) DO NOT install on a sloping surface. Install exclusively on a vertical surface. (2) DO NOT mount to cabinetry made of particleboard. (3) DO NOT install in a room with excessively high temperatures or high humidity.
Required Tools Pre-Installation Checklist Wall Stud Mounting ❏❏ For wood stud mounting, your mounting location must have at least one wall stud. Level (included) Electronic studfinder Electric hand drill ³∕₁₆" drill bit Phillips screwdriver Wrench and socket set Masking tape Masonry Mounting (brick, concrete, concrete blocks) Above tools Replace ³∕₁₆" drill bit with ½" masonry drill bit Hammer ❏❏ Your view of the mounting location must be free of glare or other obstructions.
Installing the Wall Mounting Plate Remove all pieces of the wall mounting system to ensure you have all necessary parts. The TV mounting plate and wall mounting plate come assembled in the package. Before installing mount, you must detach the two pieces as follows: 1 Detach the TV mounting plate from the wall mounting plate by loosening the security screws on either side of the wall mounting plate.
Wood Stud Mounting 1 Using an electronic studfinder, locate a wall stud at your desired mounting location. 2 With the help of another person, position the wall mounting plate on the wall stud.
Wood Stud Mounting (cont’d) 3 Suspend a straight edge, such as a ruler, across the top of the mounting plate. Place the provided level on the straight edge and confirm that the wall plate is horizontally straight. Hold the plate firmly in place. Mark the stud center in the top and bottom mounting holes with a pencil. 4 With your electric drill and ³∕₁₆" bit, pre-drill a 3" deep hole at each mark. 5 Position the wall mounting plate over the holes drilled in the wall stud.
Wood Stud Mounting (cont’d) 6 With the help of another person, attach the wall plate to the wall using the lag bolts and round washers as shown to the right. Tighten each bolt with your wrench. Turn clockwise until secure. Continue to page 14 to continue your installation. DO NOT over tighten bolts. This can damage the wall plate or the surface of your wall. DO NOT release the wall plate until you are absolutely sure it is secured to the wall.
Masonry Mounting Masonry mounting requires specialized knowledge, skills and tools. Monster highly recommends that you seek the help of a professional installer when mounting to masonry. 1 DO NOT drill holes in masonry mortar joints. With the help of a friend, position the mounting plate in the desired location. 2 Suspend a straight edge, such as a ruler, across the top of the mounting plate. Place the provided level on the straight edge and confirm that the wall plate is horizontally straight.
Masonry Mounting (cont’d) 3 With your electric drill and ½" masonry bit, pre-drill a 3" deep hole at each mark. 4 Install the supplied plastic concrete anchors in each hole. Tap into hole with hammer until fully seated. 5 Position the wall mounting plate over the holes drilled in the wall. Make sure the wall plate is level by using the supplied bubble level. Place the level on a ruler placed on top of the wall mounting plate and confirm that it is vertically straight. Hold the plate firmly in place.
Masonry Mounting (cont’d) 6 With the help of another person, attach the wall plate to the wall using the lag bolts and round washers as shown to the right. Tighten each bolt with your wrench. Turn clockwise until secure. DO NOT over tighten bolts. This can damage the wall plate or the surface of your wall. DO NOT release the wall plate until you are absolutely sure it is secured to the wall.
Setting Your Mount's Adjustment Capabilities This mount features all-directional OmniBall for fine-tuning the position of your display. ™ The OmniBall allows you to pivot your screen any direction and rotate it 360°. Before attaching your flatscreen TV to the four-point TV mounting plate, you can increase or decrease the OmniBall pivot action. 1 Slide the flatscreen TV mounting plate onto the wall plate as shown to the right.
Setting Your Mount's Adjustment Capabilities (cont’d) 3 With a socket wrench (13mm or ½"), turn the tension nut clockwise to limit pivot and rotation. 4 Turn the nut counterclockwise to increase pivot and rotation.
Attaching Your Flatscreen TV to the TV Mounting Plate Do not lay your TV face down when attaching the TV mounting plate. This can cause permanent damage to your screen. Lean it against a wall or other solid surface so it remains vertically upright. The television should be unplugged before threading any bolt or screw into the back panel. Your mounting system features two sets of screws, M4×15 and M5×15. The M5×15 is the thicker of the two.
Hanging Your Flatscreen TV on the Wall Plate 1 Connect the TV’s power cord and any AV cables to the TV before hanging it. Plug the TV’s power cord into a nearby AC outlet. If routing AV cable in wall, run it through the prepared opening in your wall. 2 With the help of another person, lift your TV up to mount level. Raise the TV just above the wall mounting plate. Slide the TV and mounting plate downward onto the wall mounting plate.
More Great Products from Monster FlatScreen ™ Get the Look You Want and the Performance You Need. Monster FlatScreen PowerProtect and PowerCenters ™ ™ Monster FlatScreen CleanView Cable Manager ™ Protect your flatscreen TV from harmful surges and spikes and maximize performance with Monster Dual Mode Plus surge protection and HD Clean Power filtering, designed specifically for HDTVs. Conceal unruly cords and cables for a clean, sleek look. Easy to install with paintable covers to match any decor.
LIMITED WARRANTY FOR CONSUMERS Monster, LLC, 7251 West Lake Mead Blvd., Las Vegas, NV 89128, USA, [PLEASE NOTE THAT MONSTER DOES NOT ACCEPT PRODUCTS SHIPPED TO THIS ADDRESS – FOLLOW INSTRUCTIONS IN “HOW TO MAKE A CLAIM” BELOW] (415) 840-2000 (“Monster”) extends You this Limited Warranty. Statutory or common law may provide You with additional rights or remedies, which shall not be affected by this Limited Warranty.
LIMITED WARRANTY FOR CONSUMERS (cont’d) JURISDICTION, AND WHICH SHALL NOT BE AFFECTED BY THIS LIMITED WARRANTY. THIS WARRANTY EXTENDS ONLY TO YOU AND CANNOT BE TRANSFERRED OR ASSIGNED. If any provision of this Limited Warranty is unlawful, void or unenforceable, that provision shall be deemed severable and shall not affect any remaining provisions. In case of any inconsistency between the English and other versions of this Limited Warranty, the English version shall prevail. REGISTRATION.