HOME THEATER BLUETOOTH SOUNDBAR WITH LIGHT SHOW AND LED ROOM ILLUMINATION MODEL:MSB3786 Please read this instruction manual carefully and keep it for future reference
CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE ELECTRIC SHOCK, DO NOT REMOVE THE COVER (OR BACK). NO USER SERVICEABLE PART INSIDE, REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. DANGEROUS VOLTAGE:The lighting flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
FCC NOTICE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
washbowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool. 6. Clean only with dry cloth The appliance should be cleaned only as recommended by the manufacturer. 7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. Slots and openings in the cabinet and in the back or bottom are provided for ventilation, to ensure reliable operation of the product and to protect it from overheating. These openings must not be blocked or covered.
moisture, does not operate normally, or has been dropped. 15. Power source This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your appliance dealer or local power company. For products intended to operate from battery power, or other source, refer to the operation instructions. 16.
20. Service Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel. 21. Replacement parts When replacement parts are required, be sure the service technician uses replacement parts specified by the manufacturer or those that have the same characteristics as the original parts. Unauthorized substitutions may result in fire or electric shock or other hazards. 22.
PROdUCT OvERvIEW FRONT VIEW 1 BT BT AUX IN LINE IN OPTICAL IN HDMI IN 2 AUX IN LINE IN OPTICAL IN HDMI IN BOTTOM VIEW 3 CONTROL PANEL 4 5 6 7 8 REAR PANEL HdMI IN arc OPTICAL IN AUX IN L 9 10 11 1. Remote Sensor 2. Mode Indicator 3. LED Light Effect 4. Volume Down Button 5. Volume Up Button 6. Power On/Off Button 7. Mode Switch Button DC LINE IN DC IN 16V, 3.5A R 12 13 8. LED Light Effect Button 9. HDMI IN arc Port 10. OPTICAL IN Jack 11. AUX IN Jack 12. LINE IN Jacks 13.
REMOTE CONTROL 1. 1 6 2. AUX Button 7 3. LINE IN Button 4. 2 AUX OPTICAL 3 LINE IN HDMI IN 8 9 10 11 BT 12 4 (Power On/Off) Button (Previous) Button 5. Sound Mode (POP, ROCK CLASSIC, STANDARD) Button 6. Light Effect Switch Button 7. (Mute) Button 8. Bluetooth Button 13 POP 5 10. CLASSIC ROCK 9. OPTICAL Button (Mode Switch) Button 11. HDMI IN Button Sound Mode STANDARD 12. (Next) Button 13. Play/Pause Button VOL 14 14.
BATTERY PRECAUTIONS Follow these precautions when using a battery in this device: 1. Use only the size and type of battery specified. 2. Be sure to follow the correct polarity when installing the battery as indicated in the battery compartment, a reserved battery may cause damage to the device. 3. Do not mix different types of batteries together ( e.g: Alkaline and Carbon -zinc ) or old batteries with fresh ones. 4.
PLACEMENT AND MOUNTING 1. Placing the device on a table - Ventilation When placing the Sound Bar on an entertainment center, bookshelf, or any type of enclosed space, be sure to allow at least 2-3 inches of space around the Sound Bar for ventilation. If the Sound Bar is enclosed in a tight space, without ventilation, heat generated from the Sound Bar could produce a potential heat hazard. 2-3inches 2-3inches 2. The Installation Distance 921mm (36.
2.1 Mounting to a wooden wall 36. 26 inch es (screws not included) A. Mark the position of the mounting screws on the wall using a pencil. B. Drill the screws directly into the marks that you have made on the wall and leave approx. 0.3 inches length to hook the sound bar. C. Put the sound bar onto the mounting screws. Make sure they are firm and stable. 2.2 Mounting to a brick wall 36. 26 inch es (screws and plastic fixing plugs are not included) A.
GENERAL OPERATION 1. Connect the AC/DC adapter to the unit and wall outlet. 2. Press the button on the unit or remote control to power on the unit. The LED light effect will light up. 3. Press the button on the unit or remote control repeatedly, or press the AUX, OPTICAL, BT, LINE IN or HDMI IN button to switch to the desired mode. The corresponding mode indicator on front of the unit will light up. 4. During Playback: ~ Press the + or - button on the unit repeatedly to adjust volume.
BLUETOOTH OPERATION 1. Power on the unit as previously explained. 2. Press the button on the unit or remote control repeatedly, or press the BT button directly on remote control to switch to the Bluetooth mode, the Bluetooth indicator on front of the unit will turn blue and blink. 3. Power on the external Bluetooth enable device and enter Bluetooth mode and try searching the unit. 4. When MONSTER SB1 appears, select it and make connection. 5.
AUX IN OPERATION An external Audio player(such as mobile phone, MP3 player etc.) can be connected to this unit and listen through the unit's speakers. 1. Plug one end of the AUX IN Cable into the AUX IN jack on the unit. 2. Plug another end of the AUX IN Cable into the headphone jack or Aux Out jack on the external audio player. HdMI IN arc OPTICAL IN DC LINE IN AUX IN DC IN 16V, 3.
LINE IN OPERATION An external Audio/Video player(such as TV, DVD player etc.) can be connected to this unit and listen through the unit's speakers. 1. Plug one end of the line in cable into the LINE IN jacks(L&R) on the unit. 2. Plug the other end of the line in cable into the Line Out jacks(L&R) on TV or DVD player etc. HdMI IN arc OPTICAL IN L white DC LINE IN AUX IN DC IN 16V, 3.5A Rear View R red Line out jacks of TV/DVD player etc. L R Video 3. Power on the unit as previously explained.
OPTICAL-IN OPERATION 1. Connect the Optical out jack from the external audio player (such as TV, DVD player etc.) to the OPTICAL IN jack on the rear of the unit with the optical connection cable as illustated below:(For PCM format only) HdMI IN arc OPTICAL IN DC LINE IN AUX IN DC IN 16V, 3.5A Rear View L R Optical Connection Cable TV or DVD player etc. OPTICAL OUT 2. Power on the unit as previously explained. 3.
HdMI IN OPERATION TV with HDMI IN arc port can be connected to this unit, and play audio through the speakers. 1. Plug one end of the HDMI cable into the HDMI IN arc port on the unit. 2. Plug the other end of the HDMI cable into the HDMI IN arc port on TV. Rear View HdMI IN arc OPTICAL IN DC LINE IN AUX IN L DC IN 16V, 3.5A R HDMI IN arc port of the TV HDMI IN arc R L Video 3. Power on the unit as previously explained. 4.
TROUBLESHOOTING SYMPTOM No power POSSIBLE CAUSE The adapter is not connected POSSIBLE SOLUTION Connect the adapter to the unit and wall outlet The unit is in power off mode Press the button on the unit or the remote control to power on the unit No sound or sound weak Sound distortion/rattle Volume level in minimum position Raise the volume level by pressing the + Button on the unit Or press VOL+ button on remote control The paired/connected device is not in playback mode Play music/movie in the
SPECIFICATIONS Power input ............................................................................AC100~240V, 50/60Hz Power output ......................................................................DC16V 3.5A Audio output .....................................................................................2x12.5W + 25W Bluetooth effective working range in open area......................................up to 32 feet Remote effective working range.......................................................
Hereby, C.I. LTD declares that this wireless speaker is in compliance with requirements of Radio Equipment Directive 2014/53/EU. Complete text of the Declaration of Conformity is available at: www.curtisint.com C.I.LTD, 7045 BECKETT DRIVE, UNIT 15, MISSISSAUGA, ON, L5S 2A3 Monster, the Monster logo and the M design are registered trademarks of Monster, Inc. and its subsidiaries in the U.S. and other countries and are used under license.
To make a warranty claim, do not return this product to the store. Please email support@curtiscs.com or call 1-800-968-9853. 90 day Warranty This product is warranted to be free from defects in material and workmanship for a period of ninety (90) days from the date of original purchase. During this period, your exclusive remedy is repair or replacement of this product or component found to be defective, at our option; however, you are responsible for all costs associated with returning the product to us.
BARRE-SON BLUETOOTH HOME THEATER AVEC SPECTACLE DE LUMIÈRES ET ÉCLAIRAGE DE LA PIÈCE MODÈLE : MSB3786 Lisez ce mode d'emploi avec attention et conservez-le pour référence future
INSTRUCTIONS DE SÉCURITÉ IMPORTANTES ATTENTION RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR ATTENTION : AFIN DE RÉDUIRE TOUT RISQUE DE CHOC ÉLECTRIQUE, NE PAS RETIRER LE BOITIER (NI LA PARTIE ARRIÈRE). L'APPAREIL NE COMPORTE AUCUNE PIÈCE REMPLAÇABLE PAR L'UTILISATEUR, CONTACTEZ LE PERSONNEL QUALIFIÉ POUR RECEVOIR DE L'ASSISTANCE.
AVIS DE LA FCC : Cet équipement à été testé et est conforme aux limites d'un appareil de Classe B, selon l'article 15 des Règles FCC. Ces limites ont étés mises en place pour offrir une protection raisonnable contre les interférences dans un complexe résidentiel. Cet équipement génère, utilise et contient de l'énergie de fréquence radio, si inutilisé incorrectement pourrait créer des interférences dangereuses pour les communications radio.
bloquées en plaçant le produit sur un lit, un canapé, un tapis ou toute autre surface similaire. Ce produit ne doit jamais être placé près ou sur un radiateur ou une source de chaleur. Ce produit ne devrait pas être placé dans une installation assemblée comme une bibliothèque ou une étagère à moins qu'une ventilation adéquate ne soit présente ou que les instructions du fabricant soient respectées.
(17) Surcharge Ne pas surcharger les prises murales et les rallonges, car cela pourrait entraîner un risque d'incendie ou de choc électrique. (18) Insertion d'objet ou de liquide Ne jamais insérer d'objet dans le produit à travers les ouvertures car il pourrait toucher des points de tensions dangereux ou faire court-circuiter des pièces, ce qui pourrait causer des feux ou chocs électriques. Ne jamais verser ou pulvériser tout type de liquide sur le produit.
(24) Dommage nécessitant une réparation Débrancher le produit de la prise murale et confier la réparation à un technicien qualifié si une des conditions suivantes est rencontrée. a) Lorsque le cordon d'alimentation ou la fiche est endommagée. b) Si du liquide a été renversé ou des objets sont tombés sur le produit. c) Si le produit a été exposé à la pluie ou à de l'eau. d) Si le produit ne fonctionne pas normalement en suivant le mode d'emploi.
PRÉSENTATION DU PRODUIT VUE AVANT 1 BT 2 AUX IN LINE IN OPTICAL IN HDMI IN AUX IN LINE IN OPTICAL IN HDMI IN VUE DU DESSOUS 3 PANNEAU DE CONTRÔLE 4 5 6 7 8 PANNEAU ARRIÈRE HdMI IN arc OPTICAL IN AUX IN L 9 10 11 1. Capteur de la télécommande 2. Indicateur de mode 3. Effets lumineux LED 4. Bouton réduction du volume 5. Bouton augmentation du volume DC LINE IN DC IN 16V, 3.5A R 12 13 8. Bouton des effets lumineux LED 9. Port ARC HDMI 10. Jack ENTRÉE OPTIQUE 12. Jack ENTRÉE LIGNE 11.
TÉLÉCOMMANDE 6 1 7 2 AUX OPTICAL 3 LINE IN HDMI IN 8 9 10 11 BT 12 4 13 POP (Marche/Arrêt) 2. Bouton AUX 3. Bouton ENTRÉE LIGNE 4. Bouton (Précédent) 5. Bouton de mode de son (POP, ROCK CLASSIQUE, STANDARD) 6. Bouton Effets lumineux 7. Bouton (Muet) 8. Bouton (Bluetooth) 9. Bouton OPTIQUE 10. Bouton (Sélection de mode) 12. Bouton (Suivant) 13. Bouton Lecture/ Pause 14. Bouton (volume +, -) 11. Bouton ENTRÉE HDMI CLASSIC ROCK 5 1.
PRÉCAUTIONS CONCERNANT LES PILES Respectez ces consignes lorsque vous utilisez une pile dans cet appareil : 1. Utilisez seulement une pile de la taille et du type spécifié. 2. Veillez à respecter le sens de polarité des piles lorsque vous les installez. Le sens est indiqué dans le compartiment des piles. Des piles installées dans le sens incorrect pourraient causer des dommages à l’appareil. 3. Ne pas mélanger différents types de piles (par ex.
POSITIONNEMENT ET MONTAGE 1. Positionner l’appareil sur une table - Ventilation Si vous posez la barre-son sur une étagère de matériel hi-fi, une bibliothèque ou tout autre type d’espace fermé, assurez-vous de ménager un espace libre de 2-3 pouces (5 à 8 cm) pour garantir la bonne circulation de l’air. Si la barre-son est installée dans un espace confiné, sans ventilation, la chaleur dégagée par la barre-son peut entraîner un danger de surchauffe. 2-3pouces(5-8cm) 2-3pouces (5-8cm) 2.
2.1 Montage sur un mur de bois 36. 26 inch es (Vis non incluses) A. Marquez la position des vis de montage sur le mur à l’aide d’un crayon. B. Percez les trous directement dans les marques faites sur le mur et laissez un espace libre d’environ 0,3 pouce (7 mm) entre la tête de vis et le mur pour suspendre la barre-son. C. Accrochez la barre-son sur les vis de montage. Assurez-vous que l’ensemble est ferme et stable. 2.2 Montage sur un mur de briques 36.
UTILISATION GÉNÉRALE 1. Branchez l’adaptateur CA/CC à l’unité et à la prise murale. 2. Appuyez sur le bouton sur l’unité ou sur la télécommande pour allumer l’unité. Les effets lumineux LED s’activeront. 3. Appuyez sur le bouton sur l’unité ou sur la télécommande de manière répétée, ou appuyez sur le bouton AUX, OPTIQUE, BT , ENTRÉE LIGNE ou ENTRÉE HDMI pour sélectionner le mode désiré. L’indicateur de mode sur l’avant de l’unité s’illuminera. 4.
FONCTION BLUETOOTH 1. Allumez l’unité comme décrit précédemment. 2. Appuyez sur le bouton sur l’unité ou la télécommande de manière répétée, ou appuyez BT directement pour activer le mode Bluetooth. L’indicateur Bluetooth sur le sur le bouton devant de l’unité clignote en bleu. 3. Allumez l’appareil Bluetooth externe, et activez le mode Bluetooth. Lancez une recherche de l’unité. 4. Lorsque MONSTER SB1 apparaît, sélectionnez le nom et effectuez la connexion. 5.
FONCTION ENTRÉE AUX Vous pouvez connecter un lecteur audio (comme téléphone mobile, un lecteur MP3, etc.) à l’unité et en diffuser le son depuis les haut-parleurs de l’unité. 1. Branchez une extrémité du câble ENTRÉE LIGNE dans le jack ENTRÉE LIGNE de l'unité. 2. Branchez l’autre extrémité du câble ENTRÉE LIGNE dans le port écouteurs ou Sortie Aux du lecteur externe. HdMI IN arc OPTICAL IN DC LINE IN AUX IN L DC IN 16V, 3.5A PANNEAU ARRIÈRE R MP3 Player Mobile Phone Lecteur Audio 3.
UTILISATION DU MODE ENTRÉE LIGNE Vous pouvez connecter un lecteur audio/vidéo externe (comme un téléviseur, un lecteur DVD, etc.) à l’unité et en diffuser le son depuis les haut-parleurs de l’unité. 1. Branchez une extrémité du câble entrée ligne dans les jacks ENTRÉE LIGNE (G et D) de l'unité. 2. Branchez l’autre extrémité du câble entrée ligne dans les jacks ENTRÉE LIGNE (G/D) du téléviseur, du lecteur DVD, etc. HdMI IN arc OPTICAL IN L blanc DC LINE IN AUX IN DC IN 16V, 3.
UTILISATION DU MODE OPTIQUE 1. Connectez le jack de sortie optique du lecteur externe (comme un téléviseur, un lecteur DVD, etc.) au jack ENTRÉE OPTIQUE sur l’arrière de l’unité avec le câble de connexion optique, comme illustré ci-dessous : (pour format PCM seulement). HdMI IN arc OPTICAL IN DC LINE IN AUX IN DC IN 16V, 3.5A PANNEAU ARRIÈRE L R TV or DVD player etc. OPTICAL OUT 2. Allumez l’unité comme décrit précédemment. 3.
UTILISATION DU MODE ENTRÉE HDMI Les téléviseurs équipés d’un port ARC HDMI IN peuvent être connectées à cette unité, et diffuser le son via les haut-parleurs. 1. Branchez une extrémité du câble HDMI dans le port ARC ENTRÉE HDMI de l'unité. 2. Branchez l’autre extrémité du câble HDMI dans le port ARC ENTRÉE HDMI du téléviseur. PANNEAU ARRIÈRE HdMI IN arc OPTICAL IN L HDMI IN arc DC LINE IN AUX IN R DC IN 16V, 3.5A R L Video 3. Allumez l’unité comme décrit précédemment. 4.
DÉPANNAGE PROBLÈME Pas d’alimentation CAUSE POSSIBLE L’adaptateur secteur n’est pas branché. L’unité est éteinte. SOLUTION POSSIBLE Branchez l’adaptateur à l’unité et à la prise murale. Appuyez sur le bouton appuyé sur l’unité ou appuyez sur la sur le bouton télécommande pour allumer l’unité. Pas de son, ou volume très Le niveau de volume est au bas minimum. L’appareil associé/connecté n’est pas en mode de lecture. La source sélectionnée est incorrecte.
Échec de réception Bluetooth ENTRÉE HDMI (ARC) non fonctionnelle L’appareil externe est trop éloigné de l’unité Rapprochez l’appareil BT externe de l’unité Non associé Associez l’unité à l’appareil BT en suivant les procédures décrites dans ce mode d’emploi. Recherchez quels canaux sont compatibles ARC sur votre téléviseur, et branchez le câble HDMI au canal ARC HDMI. Cela ne fonctionne qu’avec les canaux HDMI ARC.
CARACTÉRISTIQUES TECHNIQUES Alimentation..........................................................................................CA 100~240 V, 50/60 Hz 3,5 A Puissance de sortie ........................................................................CC 16 V Puissance de sortie audio ...............................................................................2x12,5 W + 25 W Portée efficace de la connexion Bluetooth en espace dégagé ….
Par la présente, C.I. LTD déclare que cet équipement de haut-parleur sans fil respecte les exigences de la directive sur les équipements radio 2014/53/EU. Vous pouvez consulter le texte complet de la déclaration de conformité à l’adresse : www.curtisint.com C.I.LTD, 7045 BECKETT DRIVE, UNIT 15, MISSISSAUGA, ON, L5S 2A3 Monster, le logo Monster et le logo en forme de M sont des marques déposées de Monster, Inc. et ses subsidiaires aux U.S. et les autres pays, et sont sous licence.
Pour faire une demande de garantie, ne retournez pas ce produit au magasin. Veuillez envoyer un courriel électronique à support@curtiscs.com ou appeler le 1-800-968-9853. 90 jours de garantie Ce produit est garanti contre tout défaut de matériel et de fabrication pendant une période de quatre-vingt-dix (90) jours à compter de la date d'achat d'origine.