Instruction manual

ManualsBrandsMonte Carlo Fan Company ManualsRemote ControlMCRC4R series

SAFETY INFORMATION

READ AND SAVE THESE INSTRUCTIONS

• Please read and understand this entire manual before attempting to assemble, install or operate

the product.

• Make sure that all electrical connections comply with local codes, ordinances, the National

Electrical Code and ANSI/NFPA 70-1999. Hire a qualified electrician or consult a do-it-yourself

wiring handbook if you are unfamiliar with installing electrical wiring.

• Before proceeding, be sure to shut off electricity at main switch or circuit breaker in order to avoid

electrical shock.

MCRC1, MCRC1R, MCRC2R, MCRC3,

MCRC3R, MCRC4R series

CONTENTS

Safety information ......................................................................................................................... 1

General guide................................................................................................................................ 2

Function chart................................................................................................................................ 3

Remote control setting (Dimming/Non Dimming) .......................................................................... 3

Installation and wiring.................................................................................................................... 4

Remote control setting and operation ........................................................................................... 7

Trouble shooting and warranty...................................................................................................... 9

CEILING FAN REMOTE CONTROLLER

INSTALLATION AND OPERATION INSTRUCTION

Summary of content (10 pages)

PAGE 1
CEILING FAN REMOTE CONTROLLER INSTALLATION AND OPERATION INSTRUCTION CONTENTS Safety information ......................................................................................................................... 1 General guide ................................................................................................................................ 2 Function chart................................................................................................................................
PAGE 2
General Guide This remote controller operates with 3V CR2032 battery (battery included). Store the remote controller away from excess heat or humidity Make sure the fan is set on HIGH speed and the light is in the ON position by pull chain controls originally supplied with your fan. For downrod mount fans- Remove Ceiling fan CANOPY from its mounting bracket and disconnect existing wiring for Remote control receiver installation and wiring. Replace it after installation.
PAGE 3
Item number VS Function Model\Function Fan Speed Fan off Reverse MCRC1 series v v MCRC1R series v v v v MCRC2R series v v MCRC3 v v MCRC3R series v v MCRC4R series v v MCRC1T series v v MCRC1RT series v v MCRC2RT series v v MCRC3W v v MCRC3RW v v MCRC4RW v v Light Up light SKU # v MCRC1, MCRC1AL v MCRC1RRZW/RB/BS/PN/BP, MCRC1RALRZW/RB/BS/PN/BP v v MCRC2RRZW/RB/BS/PN/BP, MCRC2RALRZW/RB/BS/PN/BP v MCRC3 v v MCRC3RRZW/RB/BS/PN/BP v v v MCRC4RRZW/RB/BS/P
PAGE 4
Installation and Wiring (Canopy Mount) Warning: Before proceeding, be sure to shut off electricity at main switch or circuit breaker in order to avoid electrical shock. Make wire connections as shown in wiring diagram using wire connectors provided. Connect WHITE wire from motor assembly to WHITE wire from remote control receiver marked TO MOTOR N, BLUE wire from motor assembly to BLUE wire from remote control receiver marked FOR LIGHT.
PAGE 5
Installation and Wiring (Switch Housing Mount) Warning: Before proceeding, be sure to shut off electricity at main switch or circuit breaker in order to avoid electrical shock. Remove switch housing from fan by unscrewing the 4 side mount screws. Keep the screws. Disconnect plugs in switch housing by pushing down on tab and pulling the plugs apart. (Fig.
PAGE 6
Wall Transmitter Installation Warning: Before proceeding, be sure to shut off electricity at main switch or circuit breaker in order to avoid electrical shock. Switch cover Note: Before installing the wall transmitter, place it in OFF position by pushing ON/OFF switch to the OFF. Ground To load Make series-wound connection for the wall transmitter with HOT wire from house.
PAGE 7
REMOTE CONTROL SETTING and OPERATION Transmitter Operation 1. Remove the battery seat from the bottom of remote control transmitter and install battery. Replace the battery seat. (Fig. 8) Back side of transmitter Note: Use a 3V CR2032 battery. The battery will weaken with age and should be replaced before leaking as this will damage the transmitter. Dispose of used battery properly, keep the battery out of reach for children. Useful tips Remove battery seat by pushing at “A” position as shown in Fig.
PAGE 8
REMOTE CONTROL SETTING and OPERATION The buttons on the remote control transmitter control the fan speed and light as follows. (Fig. 9) Press the button to get desired fan speed, Low to High and then High to Low cyclically. Press the OFF button to turn fan off. Fan speed will maintain last setting if turned off. Press this forward/reverse button to get desired airflow direction. Fan must be running to reverse. It will take about 25 seconds for fan to slow down and change rotation direction.
PAGE 9
Trouble Shooting Warning: Before beginning work, shut off the power supply to avoid electrical shock. PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION Fails to operate 1. Power is off. 1. Check main and branch fuses or circuit breakers. 2. Turn power off and turn it back, reset learn function with in 60 seconds after turn power back. 2. Learn function is not setting well. 3. Turn power off and check all wire connections. 4. Replace battery. 3. Faulty wire connection. 4. Out of battery (Transmitter).
PAGE 10
Sep.