Owner’s Guide and Installation Manual 3AMR60XXXD Series Fan cETL Model NO. : 3AMR60(X) Attach sales receipt to this card and retain as your proof of purchase DATE OF PURCHASE: RETAILER NAME: MODEL NUMBER: RETAILER ADDRESS: To register your fixture, please visit our website www.montecarlofans.com 6.6 kgs 14.
Cautions and Warnings WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING READ AND SAVE THESE INSTRUCTIONS Installation work and electrical wiring must be done by qualified person(s) in accordance with applicable codes and standards (ANSI/NFPA 70), including fire-rated construction. Use this unit only in the manner intended by the manufacturer. If you have any questions contact the manufacturer.
1 2 ON 3 ON Mounting bracket OFF OFF Before you begin installing the fan, Switch power off at Service panel and lock service disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a warning device, such as a tag, to the service panel. Use AC 120V/60HZ power supply only. 4 Before installing this fan make sure the outlet box is properly installed to the house structure.
8 9 0° ~2 15 0° ~2 15 7 Inserted nut Bracket Align the holes on blade with the screw holes on the bracket inside fan housing and partially install the blades with set screws provided. Note: The screw holes on the bracket are not vertical, install the set screws align with the screw holes as shown in illustration. Flip the fan body with blades over and insert the other blades (the blades with inserted nuts) into the other slots on the fan housing.
13 14 15 Lead wire Downrod Safety cable Yoke Canopy Downrod Canopy Canopy bottom cap 3 Set screw Yoke cover Yoke Screwdriver Canopy bottom cap Cross pin Yoke cover Place downrod over canopy, canopy bottom cap and yoke cover. Partially loosen downrod set screws from yoke at top of motor assembly. Thread lead wires and safety cable from motor assembly through downrod. Helpful hint: For easy assembling of the cross pin on the next installation step.
19 Wall Switch Black (Live) 20 Power source White (Neutral) Blue (For Light) Ground/Green White (For Light) Red (Motor 1) Purple (Motor 2) Gray (Motor 3) Green/Ground Receiver White (AC IN N) Black (AC IN L) Make wiring connections using wire connectors provided as indicated above. Red from fan to Red from remote marked Motor 1. Purple from fan to Purple from remote marked Motor 2. Gray from fan to Gray from remote marked Motor 3. Blue from fan to Blue from remote marked FOR LIGHT.
24 25 26 Install LED Light Kit Light pan 1 2 LED light fixture Reinstall the screw removed in step 22. Tighten all screws securely. Remove 3 preassembled screw from the light pan. Save screws for later use. Connect white wire from fan to white wire from LED light fixture and then connect black (or blue) wire from fan to blue (or black) wire from LED light kit. Note: If you don’t want to install the fan with LED light, go to step 29 for blanking plate installation.
REMOTE CONTROL SETTING and OPERATION Transmitter Operation Remove the battery cover from the remote control transmitter and install battery, battery provided. Replace the cover. Note: Use 2 1.5V/AAA battery. Note: If not using for long period of time, remove battery to prevent damage to remote transmitter, and store the remote transmitter away from excess heat or humidity.
The buttons on the remote control transmitter control the fan speed and light as follows. Fan speed 1 = minimum speed 3 = medium low speed 5 = medium high speed 2 = low speed 4 = medium speed 6 = high speed This button turns the fan off. Forward/Reverse button- This button is to control direction of fan rotation. Press once to change direction of the fan rotation. Fan must be running to reverse. Light button- Press this button to turn light on or off.
Trouble Shooting or wiring. In some cases, these installation errors may be mistaken for defects. If you experience any faults, installation, please call our Customer Service Center at the number printed on your parts list insert sheet. Warning means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel. Trouble 1. If fan does not start: Suggested Remedy 1.
Oct.
