Owner’s Guide and Installation Manual 4RKR60XXXD Series Fan cETL Model NO. : 4RKR60 Attach sales receipt to this card and retain as your proof of purchase DATE OF PURCHASE: RETAILER NAME: MODEL NUMBER: RETAILER ADDRESS: To register your fixture, please visit our website www.montecarlofans.com 6.6 kgs 14.
Cautions and Warnings WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING READ AND SAVE THESE INSTRUCTIONS Installation work and electrical wiring must be done by qualified person(s) in accordance with applicable codes and standards (ANSI/NFPA 70), including fire-rated construction. Use this unit only in the manner intended by the manufacturer. If you have any questions contact the manufacturer.
1 2 ON 3 ON Mounting bracket OFF OFF Before you begin installing the fan, Switch power off at Service panel and lock service disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a warning device, such as a tag, to the service panel. Use AC 120V/60HZ power supply only. 4 Before installing this fan make sure the outlet box is properly installed to the house structure.
7 8 9 Caution Light fixture Caution 2 1 Place light fixture assembly over the lead wires and attach it onto the plate on motor, aligning the keyhole slots on the top plate of light fixture with the preassembled screws on the plate. Twist clockwise till lock. 10 Caution Reinstall the screw removed in step 6. Tighten all screws securely. Caution: Handle it carefully to avoid getting hurt from the tip of the bars. 11 Loosen 2 and remove 1 preassembled screw from the top plate of light fixture.
13 14 Decorative set screw 15 Lamp Bottom plate Install the bottom plate of light fixture. Align the holes on bottom plate with the screw holes on the bars and install the bottom plate with decorative set screws provided. Helpful hint: Make small adjustment by moving the bars a little may help to align the holes with screw holes. 16 Install a 8W LED lamp. Caution: Use LED lamp only. Caution: Do not replace bulb until it cools down. 17 Flip the fan assembly over and carefully place it on Styrofoam.
19 20 21 Lead wire Safety cable Downrod Canopy 1 Canopy bottom cap Yoke cover Keeper pin Yoke 3 Set screw 2 Cross pin Thread lead wires and safety cable from motor assembly through downrod. 22 Helpful hint: For easy assembling of the cross pin on the next installation step.
25 26 Wall Switch Black (Live) Power source White (Neutral) Blue (For Light) Ground/Green White (For Light) Red (Motor 1) Purple (Motor 2) Gray (Motor 3) Green/Ground White (AC IN N) Receiver Black (AC IN L) Make wiring connections using wire connectors provided as indicated above. Red from fan to Red from remote marked Motor 1. Purple from fan to Purple from remote marked Motor 2. Gray from fan to Gray from remote marked Motor 3. Blue from fan to Blue from remote marked FOR LIGHT.
REMOTE CONTROL SETTING and OPERATION Transmitter Operation Remove the battery cover from the remote control transmitter and install battery, battery provided. Replace the cover. Note: Use 2 1.5V/AAA battery. Note: If not using for long period of time, remove battery to prevent damage to remote transmitter, and store the remote transmitter away from excess heat or humidity.
The buttons on the remote control transmitter control the fan speed and light as follows. Fan speed 1 = minimum speed 3 = medium low speed 5 = medium high speed 2 = low speed 4 = medium speed 6 = high speed This button turns the fan off. Forward/Reverse button- This button is to control direction of fan rotation. Press once to change direction of the fan rotation. Fan must be running to reverse. Light button- Press this button to turn light on or off.
Trouble Shooting or wiring. In some cases, these installation errors may be mistaken for defects. If you experience any faults, installation, please call our Customer Service Center at the number printed on your parts list insert sheet. Warning means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel. Trouble 1. If fan does not start: Suggested Remedy 1.
May.
