Owner’s Guide and Installation Manual 5ESR54XXD Series Fan UL Model NO. : 5ESR54XXD Attach sales receipt to this card and retain as your proof of purchase DATE OF PURCHASE: RETAILER NAME: MODEL NUMBER: RETAILER ADDRESS: To register your fixture, please visit our website www.montecarlofans.com 10.2 kgs 22.
Cautions and Warnings WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING READ AND SAVE THESE INSTRUCTIONS Installation work and electrical wiring must be done by qualified person(s) in accordance with applicable codes and standards (ANSI/NFPA 70-1999), including fire-rated construction. Use this unit only in the manner intended by the manufacturer. If you have any questions contact the manufacturer.
1 2 ON 3 ON Mounting bracket OFF OFF Before you begin installing the fan, Switch power off at Service panel and lock service disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a warning device, such as a tag, to the service panel. 4 Before installing this fan make sure the outlet box is properly installed to the house structure.
7 SAFETY CABLE INSTALLATION 8 9 Tab Lag screw ON Safety cable Slot Dip switches Washer Lock washer Install ball end of downrod into mounting bracket opening. Align (engage) slot on ball with tab on mounting bracket. Warning: Failure to align slot on ball with tab may result in serious injury.
13 Shipping stabilizer 14 15 Blade Blade bracket Blade assembly Blade arm medallion Align the holes of blade bracket, blade and the medallion of blade holder. Install blade bracket with blade by 4 blade screws provided. Tighten screws securely. Repeat this process for remaining blades. Remove shipping stabilizers from motor assembly. Insert blade assembly into the slot on flywheel. Install blade assembly with screws provided, aligning each of the holes as shown and tighten all screws securely.
19 20 21 HAND HELD INSTALL Battery cover Battery Attached glass onto light fixture and install the silicon washer and hex nut removed in step 17 to hold the glass. Install finial cap and the finial removed in step 17. Hand tighten the finial securely. Remove battery cover. Install 12V battery into wall remote. Duracell MN21 / Evereday A23 / GP 23A all 12V. Attach cover of remote by placing over buttons and snap the battery cover in place.
Remote Control Transmitter Features MEDIUM SPEED FAN REVERSE (Press once to change direction of the fan) Fan must be running to reverse. LED LIGHT HIGH SPEED LOW SPEED LIGHT ON/OFF SETTING AND DIMMER (Press and hold to dim light infinitely) FAN OFF SETTING (Turn fan off only) FAN SPEED: Depress “1 dot” for low speed, “2 dots” for medium or “3 dots” for high. To turn fan off press square”. LIGHT DIMMER: To turn light on, press light dimmer once quickly. To turn off press once quickly while light is on.
Trouble Shooting ,I \RX KDYH GLI¿FXOW\ RSHUDWLQJ \RXU QHZ FHLOLQJ IDQ LW PD\ EH WKH UHVXOW RI LQFRUUHFW DVVHPEO\ LQVWDOODWLRQ RU ZLULQJ ,Q VRPH FDVHV WKHVH LQVWDOODWLRQ HUURUV PD\ EH PLVWDNHQ IRU GHIHFWV ,I \RX H[SHULHQFH DQ\ IDXOWV SOHDVH FKHFN WKLV 7URXEOH 6KRRWLQJ &KDUW ,I D SUREOHP FDQQRW EH UHPHGLHG RU \RX DUH H[SHULHQFLQJ GLI¿FXOW\ LQ LQVWDOODWLRQ SOHDVH FDOO RXU &XVWRPHU 6HUYLFH &HQWHU DW WKH QXPEHU SULQWHG RQ \RXU SDUWV OLVW LQVHUW VKHHW Warning %HIRUH VHUYLFLQJ RU FOHDQLQJ XQL
Nov.