Owner’s Guide and Installation Manual 5PPR54XX Series Fan UL Model NO. : 5PPR54XX Attach sales receipt to this card and retain as your proof of purchase DATE OF PURCHASE: RETAILER NAME: MODEL NUMBER: RETAILER ADDRESS: To register your fixture, please visit our website www.montecarlofans.com 10.2 kgs 22.
Cautions and Warnings WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING READ AND SAVE THESE INSTRUCTIONS Installation work and electrical wiring must be done by qualified person(s) in accordance with applicable codes and standards (ANSI/NFPA 70-1999), including fire-rated construction. Use this unit only in the manner intended by the manufacturer. If you have any questions contact the manufacturer.
1 2 ON 3 ON Mounting bracket OFF OFF Before you begin installing the fan, Switch power off at Service panel and lock service disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a warning device, such as a tag, to the service panel. Use AC 120V/60HZ power supply only. 4 Before installing this fan make sure the outlet box is properly installed to the house structure.
7 SAFETY CABLE INSTALLATION 8 9 Tab Lag screw ON Safety cable Slot Dip switches Washer Lock washer Install ball end of downrod into mounting bracket opening. Align (engage) slot on ball with tab on mounting bracket. Warning: Failure to align slot on ball with tab may result in serious injury. Important: If using the angle mount, make sure open end of mounting bracket is installed facing the higher point of the ceiling and make sure the ceiling angle is not steeper than 30º.
13 14 15 Shipping stabilizer Plate on motor Top plate of switch housing Remove shipping stabilizers from motor assembly. Install the blade assembly to motor using the preinstalled screws. Tighten screws securely. Repeat this process for remaining blade assemblies. Loosen 2 and remove 1 preassembled screw from the plate on motor. Save screw for later use. Remove 3 set screws from top plate. Keep screws.
19 WALL MOUNT INSTALL Install wall control unit to outlet box using machine screws provided. © 2014 Monte Carlo Fan Company 20 Attach front cover to wall control unit with screws provided.
Remote Control Transmitter Features MEDIUM SPEED FAN REVERSE (Press once to change direction of the fan) Fan must be running to reverse. LED LIGHT HIGH SPEED LOW SPEED UP LIGHT ON/OFF SETTING AND DIMMER (Press and hold to dim light infinitely) FAN OFF SETTING (Turn fan off only) DOWN LIGHT ON/OFF SETTING AND DIMMER (Press and hold to dim light infinitely) FAN SPEED: Depress “1 dot” for low speed, “2 dots” for medium or “3 dots” for high. To turn fan off press square”.
Trouble Shooting ,I \RX KDYH GLI¿FXOW\ RSHUDWLQJ \RXU QHZ FHLOLQJ IDQ LW PD\ EH WKH UHVXOW RI LQFRUUHFW DVVHPEO\ LQVWDOODWLRQ RU ZLULQJ ,Q VRPH FDVHV WKHVH LQVWDOODWLRQ HUURUV PD\ EH PLVWDNHQ IRU GHIHFWV ,I \RX H[SHULHQFH DQ\ IDXOWV SOHDVH FKHFN WKLV 7URXEOH 6KRRWLQJ &KDUW ,I D SUREOHP FDQQRW EH UHPHGLHG RU \RX DUH H[SHULHQFLQJ GLI¿FXOW\ LQ LQVWDOODWLRQ SOHDVH FDOO RXU &XVWRPHU 6HUYLFH &HQWHU DW WKH QXPEHU SULQWHG RQ \RXU SDUWV OLVW LQVHUW VKHHW Warning %HIRUH VHUYLFLQJ RU FOHDQLQJ XQL
Nov.