Owner’s Guide and Installation Manual 8TNR56XXD Series Fan ETL Model NO. : 8TNR56XXD Attach sales receipt to this card and retain as your proof of purchase DATE OF PURCHASE: RETAILER NAME: MODEL NUMBER: RETAILER ADDRESS: To register your fixture, please visit our website www.montecarlofans.com 11 kgs 24.
Cautions and Warnings WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING READ AND SAVE THESE INSTRUCTIONS Installation work and electrical wiring must be done by qualified person(s) in accordance with applicable codes and standards (ANSI/NFPA 70-1999), including fire-rated construction. Use this unit only in the manner intended by the manufacturer. If you have any questions contact the manufacturer.
1 2 ON ON OFF OFF 3 Mounting bracket Before you begin installing the fan, Switch power off at Service panel and lock service disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a warning device, such as a tag, to the service panel. 4 Before installing this fan make sure the outlet box is properly installed to the house structure.
7 Spring clip 8 9 120V 25W Bulb Upper glass Partially loosen set screws for the spring clips Place upper glass on top of fan. Adjust the spring clips to hold the glass in place. Tighten all set screws securely. 10 11 12 Slot Safety cable Washer Lock washer Install ball end of downrod into mounting bracket opening. Align (engage) slot on ball with tab on mounting bracket. Warning: Failure to align slot on ball with tab may result in serious injury.
13 14 15 UP This side up Flywheel Blade This side for blade installation Partially loosen 2 of the set screws on mounting bracket corresponding to the slotted holes on the canopy upper ring. Remove the other 2 set screws. Save screws. Blade supporting ring Install blades on flywheel with set screws provided. Note: Be sure to use the set screws in the pack marked Step 14. Note: Make sure the side with a label “This side for blade installation” is installed upward.
19 20 Blue 21 Light fixture Bulb Black White Connect white wire from fan to white wire from light fixture, and then connect blue wire from fan to black wire from light fixture. Attach light fixture onto light pan. Reinstall the 3 set screws removed in step 18 and tighten all screws securely. © 2013 Monte Carlo Fan Company Install 2 G9 35W bulb. Bulb included. Warning: Over lamping the fan will result in the fan lights shutting down until the proper wattage of bulbs are installed.
Remote Controller Operation Remove the battery cover from the remote control transmitter and install battery. Replace the cover. This remote uses 12V battery, Duracell MN21 / Evereday A23 / GP 23A all 12V. Note: If not using for long periods of time, remove battery to prevent damage to remote transmitter, and store the remote transmitter away from excess heat or humidity “Set” Dip switch Set/change the dip switch position on the transmitter to desired code setting.
Install Transmitter wall mount cradle with 2 screws provided. Move the trim plate out from wall mount cradle and install the wall mount cradle with 2 screws provided. Replace the trim plate. Trim plate Wall mount cradle The receiver provides the following protective functions Lock protection- The DC motor has a build-in safety feature against blade obstruction during operation. If something obstructs the fan blades the motor will stop operation after 30 seconds of interruption.
Trouble Shooting ,I \RX KDYH GLI¿FXOW\ RSHUDWLQJ \RXU QHZ FHLOLQJ IDQ LW PD\ EH WKH UHVXOW RI LQFRUUHFW DVVHPEO\ LQVWDOODWLRQ RU ZLULQJ ,Q VRPH FDVHV WKHVH LQVWDOODWLRQ HUURUV PD\ EH PLVWDNHQ IRU GHIHFWV ,I \RX H[SHULHQFH DQ\ IDXOWV SOHDVH FKHFN WKLV 7URXEOH 6KRRWLQJ &KDUW ,I D SUREOHP FDQQRW EH UHPHGLHG RU \RX DUH H[SHULHQFLQJ GLI¿FXOW\ LQ LQVWDOODWLRQ SOHDVH FDOO RXU &XVWRPHU 6HUYLFH &HQWHU DW WKH QXPEHU SULQWHG RQ \RXU SDUWV OLVW LQVHUW VKHHW Warning %HIRUH VHUYLFLQJ RU FOHDQLQJ XQL
Nov.2013 Nov.
