Owner’s Guide and Installation Manual BF1-XX Series Fan UL Model NO. : AC-552 Attach sales receipt to this card and retain as your proof of purchase DATE OF PURCHASE: RETAILER NAME: MODEL NUMBER: RETAILER ADDRESS: To register your fixture, please visit our website www.montecarlofans.com 6.64 kgs 14.
Cautions and Warnings WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING READ AND SAVE THESE INSTRUCTIONS Installation work and electrical wiring must be done by qualified person(s) in accordance with applicable codes and standards (ANSI/NFPA 70-1999), including fire-rated construction. Use this unit only in the manner intended by the manufacturer. If you have any questions contact the manufacturer.
Preparation Warning: Before starting assembly of this product, please disconnect power to area and familiarize yourself with the safety information provided on page 2. A Determine mounting method to use. C A - Downrod Mount B - Angle Mount Important: If using the angle mount, check to make sure the ceiling angle is not steeper B than 18º. Important: If using the angle mount, make sure open end of mounting bracket is installed facing the higher point of the ceiling.
Installation Instruction (Downrod Mount) Lead wires and Safety cable Partially loosen downrod set screws from yoke at top of motor assembly. Remove keeper pin and cross pin from yoke, and save for later use. Downrod Place downrod over canopy, thread lead wires and safety cable from motor assembly through downrod. Canopy Slip downrod into motor housing yoke, aligning holes and install cross pin and keeper pin.
Canopy Installation Instruction (Flushmount) Remove and set aside canopy cover to reveal 6 holes. Notice that 3 of these holes are larger. (Fig. 5) Canopy cover Thread lead wires and safety cable through canopy. Place canopy over yoke, aligning larger holes in canopy with the 3 existing screws on top of motor housing. Install 3 screws and 3 lock washers (these screws and lock washers will be located in the hardware pack) into the remaining holes. Tighten all screws securely. (Fig. 6) Fig.
Wall Switch White Wiring Power Line Black Warning: Make sure main power is turned off before making wiring. Grounded/ Green Black Make wire connections as indicated. Connect Black and Blue wire from fan to Black (Hot) wire from house. Connect White wire from Fan to White (Neutral) wire from house. Connect all green grounded wires from fan to Grounded wire from House. Make sure that no filaments are outside of the wire connectors. (Fig. 9) Blue White Fig.
Blade installation Install blade bracket with blade by 3 blade screws and washers provided. Tighten screws securely. Repeat this process for remaining blades. (Fig. 11) Remove shipping stabilizers from motor assembly. Install the blade assembly to motor using the preinstalled screws. Tighten screws securely. Repeat this process for remaining blade assemblies. (Fig. 11) Screws Fiber washers Note: Tighten blade bracket screws twice a year. Screws Blade shipping stabilizers Blades bracket Fig.
Trouble Shooting ,I \RX KDYH GLI¿FXOW\ RSHUDWLQJ \RXU QHZ FHLOLQJ IDQ LW PD\ EH WKH UHVXOW RI LQFRUUHFW DVVHPEO\ LQVWDOODWLRQ RU ZLULQJ ,Q VRPH FDVHV WKHVH LQVWDOODWLRQ HUURUV PD\ EH PLVWDNHQ IRU GHIHFWV ,I \RX H[SHULHQFH DQ\ IDXOWV SOHDVH FKHFN WKLV 7URXEOH 6KRRWLQJ &KDUW ,I D SUREOHP FDQQRW EH UHPHGLHG RU \RX DUH H[SHULHQFLQJ GLI¿FXOW\ LQ LQVWDOODWLRQ SOHDVH FDOO RXU &XVWRPHU 6HUYLFH &HQWHU DW WKH QXPEHU SULQWHG RQ \RXU SDUWV OLVW LQVHUW VKHHW Warning %HIRUH VHUYLFLQJ RU FOHDQLQJ XQL
Mar. 2013 May.
