Installation Guide

READ & SAVE THESE INSTRUCTIONS
INSTALLATION OPERATION INSTRUCTIONS
TOOLS & MATERIALS REQUIRED
·Blade screw driver
·Adjustable wrench
·Step Ladder
·Wire cutters
·Wiring supplies as required by electrical code
CAUTION
: Before assembling your Lighting fixture, refer to the
section titled
ELECTRICAL CONNECTIONS
. If you feel you do
not have electrical wiring experience, refer to a do-it-yourself
wiring handbook or have your fixture installed by a qualified
licensed electrician.
GENERAL
WARNING:RISK OF FIRE.. MOST DWELLINGS BUILT BEFORE 1985
H
AVE SUPPLY WIRE REATED 60.REFER TO SUPPLY WIRE
M
ARKINGS ON FIXTURE.. CONSULT A QUALIFIED ELECTRICIAN
B
EFORE INSTALLING
1 To ensure the success of the installation, be sure to read
these instructions and review the diagrams thoroughly before
beginning.
2 All electrical connections must be in accordance with local
codes, ordinances, or the National Electrical Code. If you are
unfamiliar with methods of installing electrical wiring, secure the
services of the qualified licensed electrician.
3 These fixtures are intended to be mounted to a 4"x2 1/8"deep
metal octagon outlet box. The box must be directly supported by
the building structure.
4 Before starting the installation, disconnect the power by
turning off the circuit breaker or by removing the fuse at the fuse
box. Turning the power off using the light switch is not sufficient
to prevent electrical shock.
NOTE: The important safeguards and instructions appearing in
this manual are not meant to cover all possible conditions and
situations that may occur. It must be understood that common
sense, caution, and the care are factors which cannot be built
into any product. These factors must be supplied by the
person(s) caring for and operating the fixture.
UNPACK THE FIXTURE
Check the contents of the box. You should receive:
·Mounting hardware package
·Lampholder assembly(s)
·Mounting bracket
·Shade(s)-not provided on some models
·Shade attachment screws(3 for each shade)-not provided on
some models
PREPARE THE FIXTURE
NOTE FIRST TURN OFF ELECTRICITY
1 If you are replacing an existing fixture, disconnect and
remove the old fixture. Expose the supply wiring from the outlet
box.
2 Some fixtures are provided with a threaded nipple (See Fig.1
and Fig.5)or machine screws (see Fig.2 and 2A)for attaching
the fixture to the mounting bracket. If your fixture is supplied
with a threaded nipple, screw the nipple 3 complete, turns into
the mounting, bracket and lock into place with a hexagon lock
nut. If your fixture is supplied with machine screw, thread the
machine screws into the opposite side of the mounting bracket
from the green ground screw. lock the machine screws into
place with lock nuts. EXCEPTION: Ceiling mounted fixtures with
keyhole slots should have machine screw entering mounting
bracket from same side as green grounding screw (see Fig. 2A)
3 Fasten the mounting bracket to the outlet box using the
two screws supplied with the outlet box if your fixture is
supplied with a channel shape mounting bracket with
keyhole slots for attachment to the mounting surface (see
Fig.3), it will be necessary to mark the location of the
keyhole slots on the mounting surface and drill holes for
fasteners (not provided). Use fasteners suitable for the
mounting surface. The narrow end of the keyhole slot
should face up.
4 Attach grounding wire (green or bare copper) from the
supply circuit to the mounting bracket with the green
grounding attachment screw provided. Some models have
a grounding wire attached to the fixture. For models that
employ a green or bare copper grounding wire, it will be
necessary to connect the green or bare grounding wire to
the grounding conductor of the supply circuit. Attach all
grounding conductors to the mounting bracket with the
green grounding attachment screw
5 Make electrical connections-SEE BELOW
ELECTRICAL CONNECTIONS
To make electrical connections:
Connect the white wire(s) from the fixture to the white wire
of the supply circuit. Connect the black wire(s) from the
fixture to the black wire of the supply circuit. Connect the
green (or bare copper) colored wire to the grounding
conductor of the supply circuit. If your fixture is supplied
with an SPT cord connect the half of the SPT cord that is
ribbed surface to the white wire of the supply circuit.
Connect the smooth half of the wire (the half with markings)
to the black wire of the supply circuit, Use UL listed wire
connectors suitable for the size, type and number of
conductors. No loose strands or loose wire should be
present. Secure wire connectors with U.L listed electrical
tape.
FIANL ASSEMBLY
1 Spread the electrical splices so that the black wires are on one
side of the outlet box and the white wires are on the other side.
2 Place fixture against mounting surface allowing the threaded
nipple or machine screws to pass through the coverplate. Secure
with mounting nut or acorn nuts. For fixtures with channel shape
mounting bracket, place the coverplate over the channel and
secure with screws provided.
3 If applicable, place candle cover(s) over lampholder(s) before
installing bulb(s)(not provided).
CAUTION :Refer to the relamping label located near the
lampholder for recommended maximum wattage-do not exceed
recommended wattage.
4 If applicable, attach shades to fixture. Some shades require the
use of shade attachment screws. Do not overtighten these
screws-too much pressure could cause glass breaking. See Fig.4
for replacement of fabric spacer, not supplied on all models.
5 Outdoor wall fixtures must be caulked with suitable RTV or
Silicone compound around the top and sides of the coverplate to
reduce the chance of water intruding into the splicing area. Leave
the bottom clear to allow moisture means of escape.
6 Restore electricity and check the operation of your new lighting
fixture.
WIRE
OUTLET BOX
A FTER INSTALLING THE
THREADED NIPPLE INTO
THE CONNECTOR BE
SURE TO TIGHTEN THE
HEX NUT TO PROPERLY
SECURE THIS CENTER
PIPE TO THE FIXTURE
BEFORE ATTACHING
THE CLASS.
WHITE(SUPPLY)
WHITE(RXTURE)
NEX NUT
WASHER
ADJUST LENGTH
CEIUNG CANOPY
GLASS SHADE
CAP
FINLAI
CONNECTO R
HEX N UT
THREADED
Fig. 5
MOUNTING BRACKET
MACHINE SCREW
GROUND
GRO U ND
W
I
R
E
B
L
A
C
K
(
S
U
P
P
L
Y
)
B
L
A
C
K
(FIXT
URE)
NIPPLE

Summary of content (1 pages)