Owner`s manual
Page4
XG0649 - 031511
Section:SectionA:BeforeYouBegin
Installation and repairs should be done by an
authorized gas fireplace service technician. The
appliance should be inspected before use and at
least annually by a professional. More frequesnt
cleaning may be required due to exessive lint from
carpeting, bedding material, ect. It is imperative
that control compartments, burners and circulating
air passageways of the fireplace are kept clean.
NOTICE
XW2016
Important Message
Save these Instructions
The H36PV Power Vent replaces must be installed in
accordance with these Instructions Carefully read all the
Instructions in this manual rst Consult the Local Gas Branch to
determine the need for a permit prior to starting the installation
It is the responsibility of the installer to ensure this replace is
installed in compliance with the manufacturers instructions and
all applicable codes
BEFOREYOUSTART:
Pre-Installation Checklist
■ D
etermine the desired install location of your replace
■ See Section 1, Dimensions on Page 5, and refer to the
Framing Section 2 for details
■
S
elect your type and location of your Power Vent
run: Roof Mounted (EDVRSPV58) or Wall Mounted
(EDVWSPV58)
■ Your termination location should be selected to provide
the shortest possible vent run
■
L
ay out the Vent run; calculating the required elbows
and straight runs of 5"/8" ex or rigid pipe
■ Refer to the Section 4 on Page 10, "Installing the Power
Vent" for details
■
M
ontigo supplies 20' of low voltage wire, which can be
spliced to any length
This wire CANNOT run in conduit
with any other wire
■ Refer to Section 5 on Page 18, for Wiring Details
■
T
he gas connection is located on the bottom side of the
replace
■ Refer to local codes and guidelines for installation
requirements
■
I
nstallation and repairs should be done by a qualied
contractor and must conform to:
•
I
nstallations
i
n
C
anada must conform to the current
CAN/CGA B-149
1
and
2
Gas Installation Code and
local regulations
•
Installations
in
the
USA
must conform to local
codes, or in the absence of local codes to the National
Fuel Gas Code, ANSI Z223
1
-1988
•
S
ee
A
ppendix
Cf
or
i
nstallation
w
ithin
t
he
S
tate
ofMassachusetts. This replace must comply with
NFPA-54 Chapter 10
■ R
efer to Section 6 Page 21, "Installing the Gas Line" for
Details
U
nderstanding the Basic Operation
Residential H36PV replace
To operate the replace, Montigo has supplied and installed
twenty feet of low voltage wire to this electrical control panel
Connect the two wire harness to a standard single pole ON/
Off switch located at a location of your choice You may also
extent these wires to any length, as long as you select a wire
of equal quality
XW2018
Due to high operating temperatures, this appliance
should be located out of traffic & away from
furniture and draperies.
Children and adults should be alerted to the
hazards of the high surface temperature, which
could cause burns or clothing ignition.
Young children should be carefully supervised
when they are in the same room as the appliance.
Clothing or other flammable materials should not
be placed on or near the appliance.
CAUTION
Irritant
Cutting
Watch your step
Slippery floor
High temperatures
Glass hazard
Danger of suffocation
High voltage
Toxic
Flammable materials
Corrosive
Fork lift trucks
Danger overhead crane
Explosion risk
Oxidising
Danger of death
Biohazard
Laser Radiation
Danger of entrapment
Hot surface
General Warning
Blank
Gas bottles
Watch for
falling objects
Electricity
Danger for cutter
Entrapment hazard
Battery hazard
Rotating parts
Low temperature
Strong magnetic field
Optical radiation
Non ionizing
radiation
Radiation
Hazardous to the
Environment
Danger of harming
your hands
Irritant
Cutting
Watch your step
Slippery floor
High temperatures
Glass hazard
Danger of suffocation
High voltage
Toxic
Flammable materials
Corrosive
Fork lift trucks
Danger overhead crane
Explosion risk
Oxidising
Danger of death
Biohazard
Laser Radiation
Danger of entrapment
Hot surface
General Warning
Blank
Gas bottles
Watch for
falling objects
Electricity
Danger for cutter
Entrapment hazard
Battery hazard
Rotating parts
Low temperature
Strong magnetic field
Optical radiation
Non ionizing
radiation
Radiation
Hazardous to the
Environment
Danger of harming
your hands
Irritant
Cutting
Watch your step
Slippery floor
High temperatures
Glass hazard
Danger of suffocation
High voltage
Toxic
Flammable materials
Corrosive
Fork lift trucks
Danger overhead crane
Explosion risk
Oxidising
Danger of death
Biohazard
Laser Radiation
Danger of entrapment
Hot surface
General Warning
Blank
Gas bottles
Watch for
Electricity
Danger for cutter
Entrapment hazard
Battery hazard
Rotating parts
When this appliance is installed directly
on any combustible material other than
wood flooring, it must be installed on a
metal or wood panel extending the full
width and depth of the appliance or a
fire will occur causing serious injury,
property damage or even death.
XW2020
DANGER
XW2020-When-Installed_[EN].pdf 1 1/24/2011 12:48:53 PM