Owner`s manual

Page 3
C-View Residential R520-R620 Series Indoor Gas Fireplace
Part No. XG0771 - 070111
f i r e f e a t u r e
Introduction
Thank You for choosing a FireFeature Gas Fireplace.
The C-View Residential Fireplace is a linear burner power vented
replace. The R520 and R620 uses Montigo's 5”/10” Power Vent
System. This venting systems are ideal for extremely long or difcult
venting runs.
 The R520 is rated for Natural Gas at 80,000 BTU/H (23.2 Kilowatts)
Input, and Propane at 65,000 BTU/H (18.9 Kilowatts). Use 5”/10" dia
Montigo Certied Coaxial Vent.
 The R620 is rated for Natural Gas at 100,000 BTU/H (29.0 Kilowatts)
Input, and Propane at 80,000 BTU/H (23.2 Kilowatts). Use 5”/10" dia
Montigo Certied Coaxial Vent.
This manual covers installation, operation and maintenance. Lighting,
operation and care of this replace can be easily performed by the
homeowner. However, all installation and service work should be
performed by a qualied or licensed installer, plumber, or gastter who
is qualied or licensed by the state, province, region, or governing body
in which the appliance is being installed.
This manual covers all models and unless otherwise specied, the
designation C-View Residential refers to all models. Sections which
are specic to a particular model are marked with a symbol, plus
the appropriate model number.
Warranty and Installation Information:
The Montigo warranty will be voided by, and Montigo disclaims any
responsibility for, the following actions:
►Modication of the replace and/or components including Power Vent
assembly or glass panels.
►Use of any component part not manufactured or approved by Montigo in
combination with this Montigo replace system.
►Installation other than as instructed in this manual.
Consult your local Gas Inspection Branch on installation requirements
for factory-built gas replaces. Installation & repairs should be done by
a qualied contractor.
Installations in Canada must conform to the current CAN/CGA B-149.1
and .2 Gas Installation Code and local regulations.
Installations in the USA must conform to local codes, or in the absence
of local codes to the National Fuel Gas Code, ANSI Z223.1-1988.
See Appendix B for installation within the State of Massachusetts.
CAUTION!
Due to its high operating temperatures, the appliance should
be located out of trafc & away from furniture and draperies.
 Children and adults should be alerted to the hazards
of the high surface temperature, which could cause
burns or clothing ignition.
 Young children should be carefully supervised when
they are in the same room as the appliance.
 Clothing or other ammable materials should not be
placed on or near the appliance.
Installing The Fireplace
Introduction to the C-View Residential Fireplace:
The complete system will require a replace a power vent module
a electrical control panel as well as the appropriate vent system to
connect the replace to the power vent module placed in a vertical
or horizontal location. The Residential replace is not a heat efcient
replace and should not be used to heat your home. This product is a
re feature and should only be used to enhance the ambiance of the
room.
Basic Concept of the Residential Fireplace System:
The control compartment of this replace is located in the bottom of
the replace right below the burner system. All models will be sup-
plied with a Honeywell smart valve gas control and will not have a
variable ame control. There are two air switches that are controlling
the gas control system, and are located in the bottom of this replace.
These gas valves, and pressure switches communicate with the
electrical control panel via a six conductor cable supplied with the
replace.
To operate the replace, Montigo has supplied and installed twenty
feet of low voltage wire to this electrical control panel. Connect the
two wire harness to a standard single pole ON/Off switch located at
a location of your choice. You may also extent these wires to any
length, as long as you select a wire of equal quality.
The Residential Fireplace Installation Location:
The Residential Fireplace may be installed in any location that
maintains proper clearances to air conditioning ducts, electrical wiring
and plumbing. Safety, as well as efciency of operation, must be
considered when selecting the replace location. Try to select a loca-
tion that does not interfere with room trafc, has adequate ventilation,
and offers an accessible pathway for vent installation. Refer to Vent
Installation Section for more information.
WARNING
HOT GLASS WILL
CAUSE BURNS.
DO NOT TOUCH GLASS
UNTIL COOLED.
NEVER ALLOW CHILDREN
TO TOUCH GLASS.