MONUMEMT PELLET GRILL USE AND CARE MANUAL Model:86000 Please read this entire manual before installation and use of this pellet fuel-burning appliance. Failure to follow these instructions could result in property damage, bodily injury or even death. Contact local building or fire officials about restrictions and installation inspection requirements in your area. THIS PELLET GRILL IS DESIGNED FOR OUTDOOR USE ONLY SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE WWW.MONUMENTGRILLS.
Table of Contents 1. Safety warning …………………………………………………….1 2. Certificates ………………………………………………………...2 3. Explosion view……………………………………………………..3 4. Parts list……………………………………………………………4 5. Hardware…………………………………………………………..4 6. Assembly steps ………………………………………………….5-15 7. Use of the Pellet Grill ...…………………………………………...15-18 8. Button Function Description …………………………………..18-20 9. Trouble Shooting ………………………………………………...
1. Safety Warning ※FOR OUTDOOR USE ONLY. Use the device in open areas. Do not install under a combustible ceiling or overhang. Keep at least 40 inches away from flammable and explosive materials. ※Read the whole instruction carefully before installing and using the pellet grill. Install and use it as required (outdoor use only). The company will not be responsible for any property loss, personal injury or even death caused by failure to follow the instructions.
2.
3.
4. Part list Seq. Material Appellation No. Code 1 D010021363 Main Lid Qty 1 Seq. Material No.
6. Assembly steps Make sure your grill is assembled properly. Detailed assembly instructions are packed with each grill giving specific assembly procedures for each model. Follow these instructions carefully to ensure correct and safe assembly of the grill. Caution: Although we take every effort to ensure that the assembly process is as easy as possible, it is inherent with fabricated steel parts that corners and edged can cause cuts if improperly handled during assembly procedures.
BX4 BX4 -6-
BX2 -7-
GX2 -8-
BX8 CX8 DX4 -9-
DX2 EX2 FX2 DX2 EX2 FX2 - 10 -
- 11 -
AX2 - 12 -
BX4 1 2 - 13 -
- 14 -
7. Use of the Pellet Grill 7.1 Placement of the Device The pellet grill is designed for outdoor use only in an open and ventilate area. Keep the grill at least the distance shown in the picture with fixed facilities around and keep far away from flammable and combustible materials.
7.2 Selection of Fuels Only food-grade wood pellets should be with this pellet grill. Users can buy pellets of different flavors according to your own preference, but the granularity of pellets should not be more than 1.2”x0.3”. If the fuel pellets are too large, the device may be extinguished due to poor feeding. 1.2"MAX 0.3"MAX 7.
Not exceeding the filter screen igniter The device begins to ignite. White smoke will be emitted during the ignition of the fuel, and personnel can stay away from the operating device before the completion of the ignition.
Cleaning Clean grates using a wire grill brush. This should be done with each use. DO NOT use oven cleaner or abrasive cleaners on the painted grill surfaces. Use warm soapy water on all painted surfaces. clean grease pan, grease trough, and grease drain tube occasionally. A spatula can be used to scrape excess grease and a grill brush to brush clean. Do not allow grease to build up on the grease tray or in the grease trough as this can cause flare-ups inside the grill.
This is temperature switch knob. Show OFF,SMOKE(180),200,225,250,300,350, 400,450,475,HIGH(500). Position temperature indication, show S,200,225,250,300,350,400,450,475,H。 Actual temperature for PROBE 1 and PROBE 2 Actual temperature for grill body probe 8.1 Electrical Parameters (1) Input Voltage:AC110V ~ AC120V60Hz (2) Max Power:250W (3) Motor Power:25W ±10% (4) Fan Power:25W ±10% (5) Ignitor power:200W ±10% (6) Probe type:PT1000 8.
8.3 Fan Work Fan start working after machine starts. Fan will keep running for 10 min after machine shut off or temperature decrease to 130F 8.4 Fire Rod Work 1) First ignition, keep pressing the power button, the ignition rod will run for 8 min after motor running 1 min. 2)The grill will restart ignition when temperature less than 135℉ restart and will stop ignition when temperature higher than 170℉.