CAB X2 Stereo Cab Simulation Pedal Owner's Manual
Content Precautions-----------------------------------------------------------------------------01 Features----------------------------------------------------------------------------------02 Top panel----------------------------------------------------------------------------03-07 Instructions-------------------------------------------------------------------------08-09 Recommended setup------------------------------------------------------------10-13 CAB X2 editor software-----------------------------
Precautions PLEASE READ CAREFULLY BEFORE PROCEEDING Power Supply Please connect the designated AC adapter to an AC outlet of the correct voltage. Be sure to only use an AC adapter which supplies 9V DC, 300mA. Unplug the AC power adapter when not in use or during electrical storms.
Features ● High-quality IR loading stereo cabinet simulation pedal ● Includes 14 user preset slots that can store two different cabinet simulation settings each ● 11 factory cabinet simulation files with support for loading third-party impulse response files ● Choose between mono or stereo setups ● Footswitch can be assigned as a tradition on/off switch or to switch between presets ● Dual inputs (stereo) and outputs (stereo) for stereo/mono setup ● Comes with a specialized editor software for
Top panel 02 01 19 03 04 11 16 17 18 05 06 08 07 09 10 12 13 03 14 15
01. TYPE-C USB port: Connect to computer editor software to manage preset, loading IR and firmware update. 02. DV 9C Connect to center negative power supply with 9V and at least 300mA current draw. Recommend to use the original power supply to avoid unexpected noise. 03. HIGH CUT High frequency cut adjustment (Range from 3kHz to 20kHz) 04. LEVEL Volume level adjustment 05. LOW CUT Low frequency cut adjustment (Range from 25Hz to 500Hz) 06.
08. SAVE Press to switch between 1-14 preset slots, press and hold to confirm saving preset. 09. Left footswitch LED: Indicate the current cab sim is type A or type B. Blue for A, RED for B. 10. Right footswitch LED: Indicate the on/off status of the pedal. BLUE LED for on, LED off for off. 11. Preset LED: Indicates currently selected preset slot. 12. Left (A/B) footswitch: Press to switch A/B cab sim 13.
15. INPUT R 1/4"unbalanced (TS) monoaural output jack (It is the right input of the stereo setup) 16. OUTPUT A（Left) 1/4" unbalanced (TS) monoaural output jack, left cab sim analog output jack 17. OUTPUT B（Right） 1/4" unbalanced (TS) monoaural output jack, right cab sim analog output jack 18. PHONES 1/8" stereo audio headphone output jack 19.
* The regular frequency range of high and low cut Low frequency cut 80HZ~100Hz High frequency cut 10kHz High frequency cut 8kHz High frequency cut 6kHz 07
Instructions Select Preset Press SAVE button to scroll through the 14 preset slots; Or you can press two footswitches simultaneously to enter preset select mode, the LED of both footswitches, the LED of SAVE button will blink in RED. In this mode, press left/right footswitch to scroll up/down the 14 presets. The preset select mode will exit and be back to normal mode if idle for more than 3 seconds. In normal mode, the LED of both footswitches and SAVE button will stay on.
Save Presets Press and hold the SAVE button for 2 seconds to save the currently edited parameters. The button LED will blink to confirm saving is complete. Factory Reset Unplug the power cord then press and hold the SAVE button while plugging in the power cord to power on the unit. The PRESET LED will start to blink. Release the button and wait for the LED to start blinking to confirm the reset was successful. This operation can be cancelled by powering off the pedal before releasing the SAVE button.
Recommended setup Pedalboard Mono Setup MIXER/MONITOR/ AUDIO INTERFACE/ FRFR SYSTEM STOMPBOX/ EFFECT PEDALS/ PREAMP CAB Left Input Left CAB Right 10 GUITAR
Pedalboard Stereo Setup MIXER/MONITOR/ AUDIO INTERFACE/ FRFR SYSTEM MIXER/MONITOR/ AUDIO INTERFACE/ FRFR SYSTEM STOMPBOX/ EFFECT PEDALS/ PREAMP CAB Left Input Left CAB Right Input right EFFECT PEDALS CAB Left Input Left CAB Right Input Right 11 GUITAR STOMPBOX/ EFFECT PEDALS/ PREAMP GUITAR
Multi-Effect Setup MIXER/MONITOR/ AUDIO INTERFACE/ FRFR SYSTEM GUITAR CAB Left Input Left CAB Right Input Right MULTIEFFECTS BOARD MULTIEFFECTS BOARD MIXER/MONITOR/ AUDIO INTERFACE/ FRFR SYSTEM GUITAR Return SEND MULTIEFFECTS BOARD FX LOOP 12
FX LOOP with Amplifier INPUT L CAB ON MIXER/MONITOR/ AUDIO INTERFACE/ FRFR SYSTEM BYPASS SEND RETURN GUITAR INPUT AMP WITH FX LOOP Notice: In this setup, we recommend setting the output connecting to the amplifier to bypass the cab sim. The other output connecting to the mixer/FRFR system should have the cab sim on.
CAB X2 editor software CAB X2 supports computer editor software. Users can quickly adjust parameters, manage presets, load impulse response files, backup users files, etc.. Download Visit the official MOOERAUDIO website (http://www.mooeraudio.com/download.html) and download the software version that matches the operating system (OS) of your computer. OS requirements: Win7 or higher, Mac OS 10.11 or higher.
Connection After finishing the installation, connect your CAB X2 to your computer using the USB cable that comes with the unit. Open the CAB X2 EDIT software and select the icon on the top right corner to confirm connection. In the CABINET TYPE area in the left bottom, there are two different colors. Blue represents the left output signal while Red represents the right output signal.
Select Preset Click on the numbers to switch to the relevant preset patch. Select Cabinet Simulation Click on the drop-down menu under the cab picture to view and select cab sim.
Select desired cabinet simulation on the right side. Right click a desired cab sim model, decide if it is set to left output or right output in the pop up window. Preset Saving Click on the icon to save the currently selected preset. Preset Management Export Preset: Drag the number on the right-top PRESET(Device) area to the COMPUTER area to export the preset file from the CAB X2 to the computer.
Import Preset: Drag the preset from the COMPUTER area to the desired number on the PRESET (Device) area to import the preset file from the computer to the CAB X2. Click on the icon in the COMPUTER area to open the target folder of preset files in your computer. Notice: 1. Put the preset files into this folder and click the icon. Those preset files will be shown in the COMPUTER area of the software. 2. Preset files do not include third-party impulse response files.
Factory Reset Click on the icon to enter factory reset menu. A confirmation window will pop up, click on Yes to confirm reset. The CAB X2 will reboot automatically after reset is done. Notice: Factory reset will clear up all the preset patches and third-party IR files. Backup/Restore Select the icon, click on the button to backup all preset files in your CAB X2. Select the target location to start backing up files. The preset files will be packaged into a single . bfl file.
Effect list Description Name 65DLX 1×12 Based on Fender ® 65 Deluxe reverb 112 cabinet A15 1×12 Based on VOX® AC15C1 112 cabinet Twinverb.B 2×12 Based on Fender ® 67 Twin Reverb Blackface 212 cabinet AC30.S 2×12 Based on VOX® AC30 212 cabinet 59Baseman 4×10 Based on Fender ® 59 Bassman 410 cabinet 1960AG 4×12 Based on Marshall® 1960A Green Back 412 cabinet Rect.S 4×12 Based on Mesa Boogie® Recto Standard 412 cabinet German.V 4×12 Based on Diezel® Rear loaded V30 412 cabinet B.
Specification Input: 2*1/4" monoaural jack (Impedance value: 1M ohms) Output: 2*1/4" monoaural jack (Impedance value: 510 ohms), 1*1/8" stereo audio output jack (Impedance<1 Ohms) Power supply:9V DV center negative (Please ensure the voltage value of power supply is not more than 9V, ensure the polarity is correct.
SHENZHEN MOOER AUDIO CO. LTD 6F, Unit D, Jinghang Building, Liuxian 3rd Road, Bao’ an 71 District, Shenzhen, China.
