Operating instructions

ManualsBrandsMoog Videolarm ManualsSecurity CamerasDDW10CN2

www.videolarm.com

DEPUTY DOME

Bullet-Resistant IP Camera Housing

Installation and Operation Instructions for the following models:

DDW10CN2

DeputyDome™, Bullet-Resistant IP Camera System,

PTZ and 26x Day/ Night Camera System features

Heavy-Duty Metal Gear Pan/ Tilt. MPEG-4 and MJPEG video

compression format, full D1. Clear dome, with 24Vac input,

heater/ blower Tough enough to stop a 9mm bullet

PDDW10CN2 (Pressurized Version)

DeputyDome™, Bullet-Resistant IP Camera System, PTZ and

26x Day/ Night Camera System features Heavy-Duty Metal

Gear Pan/ Tilt. MPEG-4 and MJPEG video compression

format, full D1. Clear dome, with 24Vac input, heater/

blower Tough enough to stop a 9mm bullet

Before attempting to connect or operate this product,

please read these instructions completely.

CERTIFIED

81-IN5387

01-15-2009

Summary of content (13 pages)

PAGE 1
© 2009, Videolarm, Inc. All Rights Reserved DEPUTY DOME Bullet-Resistant IP Camera Housing www.videolarm.com Installation and Operation Instructions for the following models: DDW10CN2 DeputyDome™, Bullet-Resistant IP Camera System, PTZ and 26x Day/ Night Camera System features Heavy-Duty Metal Gear Pan/ Tilt. MPEG-4 and MJPEG video compression format, full D1.
PAGE 2
IMPORTANT SAFEGUARDS 1. Read Instructions - All the safety and operating instructions should be read before the unit is operated. 2. Retain Instructions - The safety and operating instructions should be retained for future reference. 3. Heed Warnings - All warnings on the unit and in the operating instructions should be adhered to. 4. Follow Instructions - All operating & user instructions should be followed. 5. Electrical Connections - Only a qualified electrician should make electrical connections. 6.
PAGE 3
NOTE: The DeputyDome™ is packed in two separate boxes, one for the housing and one for the pan/tilt and bullet-resistant liner. Installation should be completed as follows: 1. Run wiring to the chosen location. 2. Detach the housing and mount the wall bracket. 3. Make wiring connections. 4. Complete wiring runs. 5. Install the pan/tilt and make necessary adjustments. 6. Install the bullet-resistant liner. 7. Attach the housing and ome.
PAGE 4
Wiring Chart Non-Pressurized Receiver Version A. Heater 1) Red - Heater 1 2) N/C 3) Red - Heater B. Camera Power 1) Black - V2 2) Orange - V1 C. RJ45 INSTALLING THE PAN/TILT 1. Slide the pan/tilt back into place. All of the electrical connections are made by the edge connector and will be engaged at that point. 2. Place the pan/tilt inside the housing so that the alignment pins are facing the housing PC board.
PAGE 5
6. The liner should still be able to move up by about 1/16" on an inch to allow the liner to move when shot and transfer the force to the housing instead of the pan/tilt. REATTACHING THE DOME ON PRESSURIZED UNITS 1. The dome on the pressurized unit must be attached correctly for the unit to function properly. All screws and posts must line up exactly. INSTALLING THE HOUSING ON THE BRACKET 1.
PAGE 6
IP Instructions The factory default IP adress is 192.168.0.200. See IP Ready camera instruction for installation details. For Pan/Tilt control click on PTZ control icon in top right corner. Pan/Tilt control contains standard pan/tilt/camera control functions. To save preset, pull down #1 preset, move camera to desired position and then hit "save" to save preset. You can store up to 18 presets. Adjusting "speed" setting will correspondingly adjust dwell time when the preset is saved.
PAGE 7
PROCEDURES FOR PRESSURIZED HOUSINGS Filling and Reﬁlling Pressurized housings provide maximum protection for CCTV cameras and lenses. The charge of dry nitrogen inside the housing eliminates the effects of moisture, dust, insects and corrosive exhaust fumes. This allows a longer lifetime for your surveillance equipment. 1. Attach the barb to the regulator. 2. Remove the cap from the Schraeder valve. 3. Set the gauge on the regulator to between 5 and 8 psi.
PAGE 8
Exploded View for Replacement Parts 2 1 3 8 4 5 9 6 7 11 10 12 13 13 15 82 16 81 17 19 18 20 22 21 -8-
PAGE 9
Exploded View for Replacement Parts (Pan/Tilt Assembly) 25 26 27 28 29 30 31 -9-
PAGE 10
Exploded View for Replacement Parts (Pan Bearing Assembly) 35 37 36 38 39 40 - 10 -
PAGE 11
Exploded View for Replacement Parts (Network Assembly) 81 81 81 16 82 - 11 -
PAGE 12
Replacement Parts List Part No. Description 1 91-NTFL01 3/8-16 Flange Nut (4) 2 90-BTSEC06 1/4-20 x 1/2" Security screw SS (2) 3 50-VL1428 DDWC10 housing body 4 30-VL1405 DDWC10 accs mounting bracket 5 92-WSFL01 1/4 Flat Washer SS (4) 6 92-WSSL01 1/4 Split Lockwasher SS (4) 7 90-BTHH32 1/4-20 x 1/2" Hex head bolt SS (4) 8 90-BTRP31 8-32 x 3/8" Grounding screw 9 71-BLEH24 Blower, 24VDC 60MM 10 70-WPTRAN/P2 240/120V: 1.
PAGE 13
Product Registration/Warranty Thank you for choosing Videolarm. We value your patronage and are solely committed to providing you with only the highest quality products available with unmatched customer service levels that are second-to-none in the security industry.