Operating instructions

ManualsBrandsMoog Videolarm ManualsSecurity Camera AccessoriesPFH10

www.moogvideolarm.com

P F H 1 0

Outdoor Tubular Dust-Proof and Pressurized Environmental Housings

Installation and Operation Instructions for the following models:

PFH10C2W An Pressurized tubular housing, 24Vac or 12Vdc input, heater & blower with

feed-thru wall / pole mount

PFH10C2WY Pressurized tubular housing, 24Vac or 12Vdc input, heater & blower with

feed-thru wall / pole mount, adjustable sunshield

PFH10C8WY Pressurized tubular housing, PoE input with Dynamic Power Allocation, 30 watt

midspan included, heater & blower with feed-thru wall / pole mount, supports

.af PoE cameras, adjustable sunshield

DFH10C2W Dust-Proof tubular housing, 24Vac or 12Vdc input, heater & blower with

feed-thru wall / pole mount

DFH10C2WY Dust-Proof tubular housing, 24Vac or 12Vdc input, heater & blower with

feed-thru wall / pole mount, adjustable sunshield

DFH10C8WY Dust-Proof tubular housing, PoE input with Dynamic Power Allocation, 30

watt midspan included, heater & blower with feed-thru wall / pole mount,

supports .af PoE cameras, adjustable sunshield

Before attempting to connect or operate this product, please read these instructions completely.

81-IN5480

06-18-2012

Summary of content (14 pages)

PAGE 2
IMPORTANT SAFEGUARDS 1 Read these instructions. 2 Keep these instructions. 3 Heed all warnings 4 Follow all instructions. 5 Do not use this apparatus near water. 6 Clean only with damp cloth. 7 CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN Do not block any of the ventilation openings. Install in accordance with the manufacturers instructions. 8 9 SAFETY PRECAUTIONS Cable Runs- All cable runs must be within permissible distance.
PAGE 3
Limited Warranty for Moog Videolarm Products Moog Videolarm warrants these products to be free from defects in material or workmanship as follows: PRODUCT CATEGORY PARTS \ LABOR All Enclosures and Electronics* Five Poles/PolEvators™/CamEvator Three (3) Years Warrior Series™/Q-View™/IR Illuminators Five (5) Years SView Series™ Five (5) Years **6 months if used in auto scan/tour operation Controllers Five (5) Years Power Supplies Five (5) Years EcoKit Three (3) Years Accessory Brackets F
PAGE 4
PFH10 Value Features Optional Accessory Multi-Plane Adjustable SunShield position to protect against glare on lens Cable Feed Through hides and protects cables Pop Out Tabs allows for pole mounting Lanyard Cable safely retains housing during installation Installers Connection Board allows for easy hook-ups Hand Hold underlaid grip point Durable and Attractive “grite” color powder coated finish.
PAGE 5
! Electrical Specifications Contents of Box PFH10 Power 12VDC Class 2 Only 24Vac 12Vdc 29W 11W (No camera) (No camera) English 24Vac 12Vdc 29W 11W (Ninguna cámara) (Ninguna cámara) 24Vac 12Vdc 29W 11W (Aucun appareil-photo) (Aucun appareil-photo) 24Vac 12Vdc 29W 11W (Keine Kamera) (Keine Kamera) 24Vac 12Vdc 29W 11W (Nenhuma câmera) (Nenhuma câmera) 24Vac 12Vdc 29W 11W Midspan for Some Models Español Français Deutsch Portuguese (Nessuna macchina fotografica) (Nessuna macchina fotog
PAGE 6
! Proper Assembly of Mounting Bracket CAUTION: When assembling the mounting bracket, make sure all the wiring access holes are facing towards the rear of the base mounts access portal. • PRECAUCIÓN: Al montar la consola de montaje, cerciórese de que todos los agujeros de acceso del cableado son revestimiento hacia la parte posterior del portal bajo del acceso de los montajes.
PAGE 7
WALL MOUNTING 1 2 If you are running a conduit to the housing instead of through mount wiring, first install the appropriate fitting to the wall mount. Attach mount to wall with suitable hardware (not provided). • Si usted está funcionando con un conducto a la cubierta en vez del cableado directo del montaje, primero instale la guarnición apropiada al montaje de la pared. • Ate el montaje a la pared con el hardware conveniente (no proporcionado).
PAGE 8
Pole Mount Option (Use Steel Straps to Mount) 5 6 Gasket Nipples Crimp Cable Ties Cable Cable Feed cable through bracket, pierce the gasket nipples (as needed). Place the gasket as shown. Crimp the connectors as needed. Then use cable ties on the nipples to secure device, leave extra cable. • Alimente el cable a través del soporte, perfore las entrerroscas de la junta (según lo necesitado). Coloque la junta como se muestra. • Prense los conectadores según lo necesitado.
PAGE 9
Communication Power (B- Completely loosen) BNC RJ45 (568B) (A- Slightly loosen) In order to rotate the rear cover, slightly loosen the screw marked (A) and completely loosen the screw marked (B). Then make all of the nessecary wiring connections. • Para girar la cubierta posterior, afloje levemente el (a) marcado tornillo y afloje totalmente el (b) marcado tornillo. Entonces haga todas las conexiones nessecary del cableado.
PAGE 10
Reference Block [15] 12 Reference Block [15] 13 NOTE: The power distribution board is designed with a 24Vac / 12Vdc selector switch. If the Switch is set at 24Vac, then voltage input should be 24Vac. 24Vac will then be output to the camera. If the Switch is set at 12Vdc, then voltage input should be 12Vdc, 12Vdc will then be output to the camera. The selector switch is to allow the housing to operate at either voltage.
PAGE 11
17 16 Camera Sled Ring Screw Camera Sled Loosen the screws shown on the picture and turn the camera sled ring to the desired angle and re-tighten. Install the camera using provided screws and rubber spacer, to center lens (if needed). • Instale la cámara usando los tornillos proporcionados y el espaciador de goma, a la lente de centro (si es necesario). • Afloje los tornillos demostrados en el cuadro y dé vuelta al anillo del trineo de la cámara al ángulo deseado y vuélvalo a apretar.
PAGE 12
Pressurize the Unit Cont. 20 Place the air chuck on the fill valve and begin filling until pressure relief valve opens. • Coloque la tirada del aire en la válvula del tanque y comience a llenar hasta que la válvula de descarga de presión se abra. • Placez le mandrin d'air sur la valve de réservoir et commencez à remplir jusqu'à ce que la valve de décompression s'ouvre. • Setzen Sie die Luftklemme auf das Behälterventil und fangen Sie an zu füllen, bis Druckablassventil sich öffnet.
PAGE 13
22 After purging and refilling, check the housings pressure. It should be around 5-7psi (0.35-0.5bar). Connectors Over - Pressure Relief Valve 10 5 0 Fill Valve 15 • Después de purgar y de rellenar, compruebe la presión de las cubiertas. Debe estar alrededor de 5-7psi (0.35-0.5bar). • Après la purge et le remplissage, vérifiez la pression de logements. Elle devrait être autour de 5-7psi (0.35-0.5bar). • Nachdem Sie bereinigt haben und wieder gefüllt haben überprüfen Sie den Gehäusedruck.
PAGE 14
Product Registration/Warranty Thank you for choosing Moog Videolarm. We value your patronage and are solely committed to providing you with the highest quality products available and superior customer service. Should a problem arise, rest assure that Moog Videolarm stands behind its products by offering impressive warranty plans: 3 Years on all Housings, Poles, Power Supplies, and Accessories and 5 Years on camera systems (SView, QView, Warriors), and InfraRed Illuminators.